Olimpia Splendid B0152 User manual

Type
User manual

This manual is also suitable for

MI078945_Rev1114_278117A
10
n. u. = Non utilizzare - Do not Use - Ne pas utiliser
- Nicht benutzen - No utilice
Manuale istruzioni
Instructions manual
Mode d’emploi
Bedienungsanleitung
Manual de instrucciones
B0152
www.olimpiasplendid.it
1
2
4
3
5
6
7
10
8
9
NTC
n.u.
M
Ev
N
L
N
L
230 V~
V1
V2
V3
Valvola acqua
Water valve
Vanne à eau
Wasserventi
Válvula agua
Sonda temperatura acqua
Water temperature probe
Sonde de température de l’eau
Wasser Fühle
Sensor de temperatura agua
Motoventilatore
Fan
Motoventilateur
Motorventilator
Motoventilador
Velocità minima / media / massima
Minimum / medium / maximum speed
Vitesse minimale / moyenne / maximale
Minimum/mittel/maximum Geschwin
-
digkeit
Velocidad mínima / media /màxima
LEGENDA · LEGEND · LÉGENDE
LEGENDE
· LEYENDA
Ev =
NTC =
M =
V1
V2
V3 =
T+ T- V+ V- A/M RESET E/I OFF
T+ T- V+ V- A/M RESET E/I OFF
T+ T- V+ V- A/M RESET E/I OFF
T+ T- V+ V- A/M RESET E/I OFF
T+ T- V+ V- A/M RESET E/I OFF
T+ T- V+ V- A/M RESET E/I OFF
1
2 4 5
6 8 9
7
3
A
B
C
CARATTERISTICHE TECNICHE
ALIMENTAZIONE ................................................................................
POTENZA ASSORBITA MASSIMA .................................................
CAMPO DI REGOLAZIONE TEMPERATURA ..............................
INTERVALLO MINIMO DI REGOLAZIONE TEMPERATURA ...
VISUALIZZAZIONE TEMPERATURA AMBIENTE ........................
DIFFERENZIALE DI REGOLAZIONE ...............................................
SONDA AMBIENTE A BORDO ........................................................
SONDA ACQUA (NON FORNITA) ...................................................
USCITE ....................................................................................................
PORTATA CONTATTI ..........................................................................
GRADO DI PROTEZIONE ....................................................................
CLASSE DI ISOLAMENTO .................................................................
GRADO DI INQUINAMENTO ............................................................
CLASSE DI SOFTWARE ....................................................................
GRADIENTE TERMICO .......................................................................
TEMPERATURA MASSIMA DI FUNZIONAMENTO ....................
LIMITI DI UMIDITÀ ............................................................................
TEMPERATURA DI STOCCAGGIO ...................................................
COMMUTAZIONE ................................................................................
MONTAGGIO ........................................................................................
230V~/50Hz (+10% -15%)
3VA
5°C÷35°C
0,1°C
0÷40°C (risoluzione 0,1°C)
IMPOSTABILE (0,5K di fabbrica)
NTC 100K @25°C ±1%
NTC 2K @25°C a doppio isolamento
4 Rele (3 velocità motore + 1 elettrovalvola)
3(1A) – 250Vac
IP 20 (a prodotto installato)
2
A
1K/15min.
50°C
20% .. 80% RH (non condensante)
0÷60°C
ESTATE/INVERNO (riscaldamento/condizionamento)
in scatola standard da incasso 3 moduli (DIN503)
The technical data contained in this documentation are not binding. The Manufacturer reserves itself
the right to make all the changes deemed necessary at any time in order to improve the product.
INTRODUCTION
We would like to thank you for your loyalty and congratulate you for choosing our product. This
device is a high performance flush-mounted electronic regulator for fan coil. It regulates the room
temperature to a precise level in the location where it is installed and is able to meet all the needs of
users in terms of ambient COMFORT. To correctly use the device, you are advised to carefully read this
instructions manual and keep it for any future consultation.
COMPLIANCE WITH DIRECTIVES
• 2006/95/EC (LVD)
• 2004/108/EC (EMC)
• 2011/65/UE (RoHS)
PACKAGE CONTENTS
• 1 flush-mounted electronic regulator for fan coil
• User manual and wiring diagrams
COMPLIANCE WITH STANDARDS
• EN 60730-1
• EN 60730-2-9
• 1 support frame
• 2 aesthetic covers
SPECIFICATIONS
POWER SUPPLY ................................................................................
MAX POWER CONSUMPTION ........................................................
TEMPERATURE ADJUSTMENT RANGE ..........................................
REGULATION RESOLUTION ...........................................................
ROOM TEMPERATURE DISPLAY .....................................................
DIFFERENTIAL REGULATION VALUE ...........................................
ON-BOARD ROOM TEMPERATURE SENSOR ...........................
WATER TEMPERATURE PROBE (NOT SUPPLIED) ......................
OUTPUTS ................................................................................................
CONTACT RATING ..............................................................................
DEGREE OF PROTECTION .................................................................
INSULATION CLASS ...........................................................................
DEGREE OF POLLUTION....................................................................
SOFTWARE CLASS .............................................................................
THERMAL GRADIENT .....................................................................
MAXIMUM OPERATING TEMPERATURE .......................................
HUMIDITY LIMITS ..............................................................................
STORAGE TEMPERATURE ................................................................
SWITCHING ..........................................................................................
ASSEMBLY .............................................................................................
230V~/50Hz (+10% -15%)
3VA
5°C÷35°C
0,1°C
0÷40°C (resolution 0,1°C)
SETTABLE (0,5K factory setting)
NTC 100K @25°C ±1%
NTC 2K @25°C with double insulation
4 Relays (3 motor speeds + 1 solenoid valve)
3(1A) – 250Vac
IP 20 (with installed product)
2
A
1K/15min.
50°C
20% .. 80% RH (non-condensing)
0÷60°C
SUMMER/WINTER (heating/air conditioning)
in standard, 3-module flush-mounting box (DIN503)
DIMENSIONS (fig. 1)
LCD DISPLAY KEY (fig. 6)
REGULATOR CONTROLS KEY (fig. 7)
A. Displays room temperature
B. Indicates fan speed
C. Automatic fan speed mode enabled
D. Summer (air conditioning) ( ) or winter ( ) mode
E. Indicates keypad lock enabled
F. Displays temperature entered
G. System working (steady light)
or locked by minimum thermostat operation (flashing light)
A. Temperature keys (T+/T-)
B. Fan speed keys (V+/V-)
C. Automatic fan mode key (A/M)
D. RESET key to restart the device (RESET)
E. Summer/winter mode key (E/I)
F. System OFF key (OFF)
230V~/50Hz (+10% -15%)
3VA
5°C÷35°C
0,1°C
0÷40°C (resolution 0,1°C)
SETTABLE (0,5K factory setting)
NTC 100K @25°C ±1%
NTC 2K @25°C with double insulation
4 Relays (3 motor speeds + 1 solenoid valve)
3(1A) – 250Vac
IP 20 (with installed product)
2
A
1K/15min.
50°C
20% .. 80% RH (non-condensing)
0÷60°C
SUMMER/WINTER (heating/air conditioning)
in standard, 3-module flush-mounting box (DIN503)
INSTALLATION AND CONNECTIONS
SAFETY REQUIREMENTS
Before connecting the regulator to the system make sure that the mains voltage IS NOT CONNECTED
and that it corresponds to the voltage indicated on the back of the regulator (230V~ /50Hz).
POSITIONING
The position of the thermostat may significantly affect its performance. Install the device on the inner
wall of a room in which you usually stay, away from draughts (doors, windows, fans, etc.), sources of
heat (radiators, sun’s rays, kitchens, household appliances such as televisions, refrigerators, computers,
etc.) and vibrations, about 1.5 m from the floor ensuring regular air flow, if necessary sealing the
outlet tube of the connection cables (fig. 2).
INSTALLATION
The regulator is already mounted inside its housing and fastened to the appropriate standard SUPPORT
FRAME, so only the following installation operations are required:
• Perform the connections as described in the paragraph below “Electrical wirings”.
• House the Regulator with its SUPPORT FRAME (fig.3B) in the 3-module box previously embedded
into the wall (fig.3C) and fasten it with the screws supplied.
• Pressure mount the desired PLATE (Fig.3A).
PLATE ASSEMBLY
By means of the specifically designed SUPPORT FRAME, a set of specific PLATES can be assembled on
the product, instead of the one supplied as standard equipment:
• BTicino series LIVING INTERNATIONAL
• Gewiss series PLAYBUS and PLAYBUS YOUNG
• Vimar series IDEA and IDEA RONDÒ
If a PLATE from the LIVING INTERNATIONAL, PLAYBUS or PLAYBUS YOUNG series is mounted, the two
“wings” at the side of the SUPPORT FRAME should be broken off and discarded (fig. 5).
If a PLATE from the IDEA or IDEA RONDÒ series is mounted, it is not necessary to modify the SUPPORT
FRAME: the “wings” should be left on the edges of the SUPPORT FRAME (fig. 4).
NOTE: two plastic splints have been supplied with the product to cover the holes, which would other-
wise be visible on the front of the regulator if the Gewiss or Vimar PLATES are installed.
ELECTRICAL WIRINGS
Carry out the wirings according to the electrical diagram shown in this manual (fig.10).
INSTALLING THE MINIMUM/MAXIMUM PROBE
To use the minimum/maximum temperature detection probe of the system fluid with the wall-
mounted control, proceed as follows:
- Identify the water temperature probe already assembled on the fan coil unit.
- Connect the probe to the regulator as indicated in the diagram (fig. 10), using the bipolar cable with
double insulation and maximum overall length equal to 10 m. This connection must be maintained
separated from the power supply cables and any other power cables available. The junction between
probe and connection cable must be maintained suitably protected and not accessible from outside the
fan coil. Do not connect or disconnect the probe with the powered regulator.
ATTENTION!
THE DEVICE MUST BE INSTALLED BY QUALIFIED PERSONNEL IN COMPLIANCE WITH THE
SAFETY STANDARDS AND LAWS IN FORCE.
CUT THE POWER BEFORE MAKING OR INTERVENE ON ANY ELECTRICAL CONNECTION.
THE MANUFACTURER IS NOT LIABLE FOR ANY IMPROPER USE OF THE PRODUCT.
KEYS FUNCTIONS (fig. 7)
SWITCHING ON THE REGULATOR
Once you have connected and powered the device, press the RESET button for 2-3 seconds with the
tip of a pencil. All the segments and symbols available will appear on the display for a few
seconds (AUTOTEST). After that the regulator gets switched off, in heating mode. See the paragraphs
below to perform the required settings.
SETTING THE TEMPERATURE
Use keys T+ and T- to set the desired temperature, displayed at the bottom right.
MANUAL SETTING OF THE FAN SPEED
Use keys V+ and V- to set the desired fan speed.
AUTOMATIC FAN OPERATION
Press key A/M to start automatic operation of the fan. The speed will be proportional to the difference
between the desired temperature and the one actually measured (higher the difference -> the greater
the speed). Press key A/M once again to go back to the manual operating mode of the fan.
DEVICE RESET
Press the RESET key to perform an AUTOTEST of the system and return to the normal operating mode.
The values set will not be lost (fig. 8).
RESETTING TO FACTORY SETTINGS
Hold button V+ down when you RESET the device. By releasing the V+ key after its reactivation , the
equipment will switch on with all operating parameters at the factory-set values.
SUMMER/WINTER MODE
The regulator can be set to “summer” or “winter” mode depending upon whether it is connected to an
air conditioner or heater. Press the E/I (S/W) key to change from one mode to the other (fig. 9). The
“summer” mode is displayed by the “snow” symbol ( ), while the “winter” mode is displayed by the
“sun” symbol ( ) (fig. 6D).
KEYPAD LOCK
Press the E/I key for at least 7 seconds to enable the keypad lock. The corresponding symbol will
appear on the display (fig. 6E). None of the keys will be enabled at this point. Press the E/I key again
for 7 seconds to return to the normal state.
SWITCHING OFF THE SYSTEM
Through the OFF button, you can switch off the system. The values set will not be lost. Press any key
to switch the system on.
MINIMUM AND MAXIMUM THERMOSTAT FUNCTION
This function is active with the device in both MANUAL and AUTOMATIC operating mode when the
probe is used to control the system water temperature. It allows the fan to be blocked until the water
temperature reaches the values suitable for the required regulation. This way, environmental comfort is
improved and consumptions are considerably reduced. Any system activation request in this situation is
indicated in the display with the “FLAME” symbol flashing (fig. 6G).
WINTER OPERATION: The fan motor is disabled when the water temperature drops below the value
pre-set for the P5 adjustable parameter (Default value 30°) with 3 °C hysteresis.
SUMMER OPERATION: The fan motor is disabled when the water temperature rises above the value
pre-set for the P7 adjustable parameter (Default value 20 °C) with 3 °C hysteresis.
In case of faults in the probe, the fan and solenoid valves are disabled. The display indicates error code
E03 or E04 depending on whether the probe is acknowledged as open or in short circuit.
This function is EXCLUDED if no water temperature probe is connected when the device is turned on.
TEMPERATURE UNIT OF MEASUREMENT SELECTION FUNCTION
The unit of measurement of the temperature can be modified from °C (default value) to °F and vice-ver-
sa by following the procedure described in paragraph “ MODIFICATION OF OPERATING PARAMETERS”.
FUNCTIONS
MANUAL SUMMER MODE
The solenoid valve activates when the room tem-
perature RISES above the value pre-set for the P0
adjustable parameter (default value 0.5K) compared
to the value required (set point). The fan is always
active at the speed set from the keyboard and it is
independent from the temperature control system.
(Forced ventilation system)
Display:
snow symbol (summer)
fan speed entered symbol
set point entered
room temperature
flame symbol if electrovalve activated
E2 o
SET POINT
E2 on
E2 on
+ 0,5°C
V 3
V 2
E2 on
V 1
E2 on
V 1
E2 o
V 3
E2 on
V 2
E2 on
V 1
E2 on
T.A.
T.A.
0,5°C
0,5°C
0,5°C
0,5°C
0,5°C
Set Point
E2 o
V 1
SET POINT
--------
E1 o
E1 on
-0,5°C
E1 on
SET POINT
------
V 3
V3
E1 on
V2
E1 on
V1
E1 o
T.A.
T.A.
0,5°C
0,5°C
Set Point
E1 o
V 1
V1
E1 on
V2
E1 on
V1
E1 on
0,5°C
0,5°C
0,5°C
E on
E on
+0,5°C
E o
SET POINT
ventola on
ventola on
+0,5°C
ventola o
SET POINT
V 3
V 3
E on
V 2
E on
V 1
E on
T.A.
T.A.
1°C
1°C
1°C
1°C
1°C
Set Point
E o
V o
V 2
E on
V 1
E on
V o
E o
SET POINT
--------
E o
E on
-0,5°C
E on
-0,5°C
ventola on
ventola on
SET POINT
-------
ventola o
SET POINT
------
SET POINT
------
V 3
E on
V 3
E on
V 2
E on
V o
E o
T.A.
T.A.
1°C
1°C
Set Point
E o
V o
V 1
E on
V 2
E on
V 1
E on
1°C
1°C
1°C
+ 1C°
E2 on
E2 on
SET POINT
E1, E2 o
- 1C°
E1 on
E1 on
V 3
V 2
E2 on
V 1
E2 on
V 1
E2 o
V 3
E2 on
V 2
E2 on
V 1
E2 on
T.A.
T.A.
0,5°C
0,5°C
0,5°C
0,5°C
0,5°C
E2 o
V 1
V 3
V3
E1 on
V2
E1 on
V1
E1 o
T.A.
T.A.
0,5°C
0,5°C
Set Point
E1 o
V 1
V1
E1 on
V2
E1 on
V1
E1 on
0,5°C
0,5°C
0,5°C
1° 1C °C
1° 1C °C
E = Water electrovalve
OPERATION LOGIC
AUTOMATIC SUMMER MODE
The fan is active with speed proportional to the dif-
ference between temperature detected and set and it
is deactivated as soon as the required temperature is
reached. The speed changes according to the value set
for the P1 adjustable parameter (default value 1K).
The solenoid valve is active when the fan is active.
Display:
snow symbol (summer)
AUTO symbol (flashing )
fan speed activated symbol
set point entered
room temperature
flame symbol if electrovalve activated
E2 o
SET POINT
E2 on
E2 on
+ 0,5°C
V 3
V 2
E2 on
V 1
E2 on
V 1
E2 o
V 3
E2 on
V 2
E2 on
V 1
E2 on
T.A.
T.A.
0,5°C
0,5°C
0,5°C
0,5°C
0,5°C
Set Point
E2 o
V 1
SET POINT
--------
E1 o
E1 on
-0,5°C
E1 on
SET POINT
------
V 3
V3
E1 on
V2
E1 on
V1
E1 o
T.A.
T.A.
0,5°C
0,5°C
Set Point
E1 o
V 1
V1
E1 on
V2
E1 on
V1
E1 on
0,5°C
0,5°C
0,5°C
E on
E on
+0,5°C
E o
SET POINT
ventola on
ventola on
+0,5°C
ventola o
SET POINT
V 3
V 3
E on
V 2
E on
V 1
E on
T.A.
T.A.
1°C
1°C
1°C
1°C
1°C
Set Point
E o
V o
V 2
E on
V 1
E on
V o
E o
SET POINT
--------
E o
E on
-0,5°C
E on
-0,5°C
ventola on
ventola on
SET POINT
-------
ventola o
SET POINT
------
SET POINT
------
V 3
E on
V 3
E on
V 2
E on
V o
E o
T.A.
T.A.
1°C
1°C
Set Point
E o
V o
V 1
E on
V 2
E on
V 1
E on
1°C
1°C
1°C
+ 1C°
E2 on
E2 on
SET POINT
E1, E2 o
- 1C°
E1 on
E1 on
V 3
V 2
E2 on
V 1
E2 on
V 1
E2 o
V 3
E2 on
V 2
E2 on
V 1
E2 on
T.A.
T.A.
0,5°C
0,5°C
0,5°C
0,5°C
0,5°C
E2 o
V 1
V 3
V3
E1 on
V2
E1 on
V1
E1 o
T.A.
T.A.
0,5°C
0,5°C
Set Point
E1 o
V 1
V1
E1 on
V2
E1 on
V1
E1 on
0,5°C
0,5°C
0,5°C
1° 1C °C
1° 1C °C
E = Water electrovalve
V1 = Minimum speed
V2 = Medium speed
V3 = Maximum speed
T.A. = Room temperature
MANUAL WINTER MODE
The solenoid valve activates when the room tem-
perature DROPS below the value pre-set for the P0
adjustable parameter (default value 0.5K) compared
to the value required (set point). The fan is always
active at the speed set from the keyboard and it is
independent from the temperature control system.
(Forced ventilation function)
Display:
sun symbol (winter)
fan speed entered symbol
set point entered
room temperature
flame symbol if electrovalve activated
E2 o
SET POINT
E2 on
E2 on
+ 0,5°C
V 3
V 2
E2 on
V 1
E2 on
V 1
E2 o
V 3
E2 on
V 2
E2 on
V 1
E2 on
T.A.
T.A.
0,5°C
0,5°C
0,5°C
0,5°C
0,5°C
Set Point
E2 o
V 1
SET POINT
--------
E1 o
E1 on
-0,5°C
E1 on
SET POINT
------
V 3
V3
E1 on
V2
E1 on
V1
E1 o
T.A.
T.A.
0,5°C
0,5°C
Set Point
E1 o
V 1
V1
E1 on
V2
E1 on
V1
E1 on
0,5°C
0,5°C
0,5°C
E on
E on
+0,5°C
E o
SET POINT
ventola on
ventola on
+0,5°C
ventola o
SET POINT
V 3
V 3
E on
V 2
E on
V 1
E on
T.A.
T.A.
1°C
1°C
1°C
1°C
1°C
Set Point
E o
V o
V 2
E on
V 1
E on
V o
E o
SET POINT
--------
E o
E on
-0,5°C
E on
-0,5°C
ventola on
ventola on
SET POINT
-------
ventola o
SET POINT
------
SET POINT
------
V 3
E on
V 3
E on
V 2
E on
V o
E o
T.A.
T.A.
1°C
1°C
Set Point
E o
V o
V 1
E on
V 2
E on
V 1
E on
1°C
1°C
1°C
+ 1C°
E2 on
E2 on
SET POINT
E1, E2 o
- 1C°
E1 on
E1 on
V 3
V 2
E2 on
V 1
E2 on
V 1
E2 o
V 3
E2 on
V 2
E2 on
V 1
E2 on
T.A.
T.A.
0,5°C
0,5°C
0,5°C
0,5°C
0,5°C
E2 o
V 1
V 3
V3
E1 on
V2
E1 on
V1
E1 o
T.A.
T.A.
0,5°C
0,5°C
Set Point
E1 o
V 1
V1
E1 on
V2
E1 on
V1
E1 on
0,5°C
0,5°C
0,5°C
1° 1C °C
1° 1C °C
E = Water electrovalve
AUTOMATIC WINTER MODE
The fan is active with speed proportional to the dif-
ference between temperature detected and set and it
is deactivated as soon as the required temperature is
reached. The speed changes according to the value
set for the P1 adjustable parameter (default value
1K). The solenoid valve is active when the fan is
active.
Display:
sun symbol (winter)
AUTO symbol (flashing )
fan speed activated symbol
set point entered
room temperature
flame symbol if electrovalve activated
V 3
V 3
E on
V 2
E on
V o
E o
T.A.
T.A.
1°C
1°C
Set Point
E o
V o
V 1
E on
V 2
E on
V 1
E on
1°C
1°C
1°C
E = Water electrovalve
V1 = Minimum speed
V2 = Medium speed
V3 = Maximum speed
T.A. = Room temperature
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
The equipment/
system
does not
switch on
1. Wrong connections
2. Wrong contact
3. Wrong connections
4. Wrong summer/winter
setting
1. check the connections between the power supply wires (230V ~) and the
regulator terminals n°1-2
2. Press RESET key
3. Check the connections between the CHARGE wires and the regulator
terminals
4. Make sure that the display shows the “sun” symbol (
), in WINTER
mode or the “snow” symbol (
), in SUMMER mode.
The temperature
displayed does not
correspond to
the actual
temperature
5.Wrong regulator location
6. Air current coming from
tube conduit containg
the wires from the system
to the regulator
5./6. Follow the instructions in the “Location” paragraph
The display does
not switch on
after pressing
the RESET key
7. The RESET key is in the
wrong position under the
plastic part
7. Use the tip of a pencil to release the key and return it to the
correct position
PROBLEM POSSIBLE CAUSE SOLUTION
Keys don’t seem to
work
8. Keypad lock enabled 8. Disable the keypad lock as described
E01 or E02 is
displayed
9.Integrated room sensor is
broken or in short circuit
9. Press the RESET button. In case of persistent anomaly, replace
the device
E03 or E04 is
displayed
10. Water probe is bro
-
ken or in short circuit
10. Check the accuracy and integrity of the probe and its connections,
and replace it if necessary.
11. Disconnect the device from the main power supply, remove the
probe to inhibit the minimum/maximum function, connect the device to
the power supply
The device beha
-
ves irregularly
12. Unidentifiable cause 12. Press the RESET key and, if the problem persists, replace the device.
Do not tamper with any part of the product for any reason.
In case of persistent anomalies, contact a technician you trust or the store where you purchased the
device.
With the thermostat in the OFF condition, press the OFF key and keep it pressed. After about 10
seconds, the display will show the firmware version on the left of the screen (large characters) and
the set operating mode on the right (small characters). If no key is pressed for about 30 seconds, the
device goes back to the OFF condition; otherwise, keys V+ and V- can be used to browse through the
list of parameters, which can be changed by means of keys T+ and T-. Once all parameters have been
changed, press A/M key to store them and return to normal operation, or press the OFF key to return
to normal operation without making any changes to the parameters.
MODIFICATION OF OPERATING PARAMETERS
WARNING!
The temperature parameters
are always expressed as °C or °F
depending upon the unit of me-
asure selected (parameter 3).
P3
°
C
1 = °C
2 = °F
P4
P0 0,5 K 0,4K-1K (if ° F 0,7K-1,8K)
P1 1 K 0,4K-1K (if ° F 0,7K-1,8K)
P2
P5
P6
30°C
-2K
30
-5,0 ÷ +5,0 K
P7 20°C 10 ÷ 30°C
÷
50°C
Parameter
Description
Manufacturer’s setting From - to
Temperature unit of
measure
Room temperature
offset
Max. water temperature
threshold (SUMMER)
Not used
Regulation differential
Fan control hysteresis
Not used
Min. water temperature
threshold (WINTER)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94

Olimpia Splendid B0152 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI