Ransomes 67042, 67043 Accessories Manual
- Category
- Engine
- Type
- Accessories Manual
JACOBSEN
®
TRI-KING ANTI-VIBRATION KIT
Product Code: LMAC020
JACOBSEN
WARNING: If incorrectly used this machine can cause
severe injury. Those who use and maintain this machine
should be trained in its proper use, warned of its dangers
and should read the entire manual before attempting to
set up, operate, adjust or service the machine.
GB
Part No.24519G (rev.0)(RJ 100 072002)
Fitting Instructions & Parts
© 2002, Textron Inc. All Rights Reserved
GB-1
TRI-KING ANTI-VIBRATION KIT
FITTING INSTRUCTION MANUAL
GB
1 CONTENTS
CONTENTS PAGE
1 CONTENTS ................................................................................................................ 1
2 SAFETY INSTRUCTIONS ........................................................................................... 2
2.1 OPERATING INSTRUCTIONS ........................................................................... 2
2.2 SAFETY SIGNS .............................................................................................. 2
2.3 STARTING THE ENGINE...................................................................................2
2.4 DRIVING THE MACHINE...................................................................................2
2.5 TRANSPORTING ............................................................................................. 2
2.6 LEAVING THE DRIVING POSITION ................................................................... 2
2.7 SLOPES ......................................................................................................... 2
2.8 BLOCKED CUTTING CYLINDERS ..................................................................... 3
2.9 ADJUSTMENTS, LUBRICATION & MAINTENANCE ............................................ 3
3 ANTI-VIBRATION KIT FITTING INSTRUCTIONS ........................................................ 4
4 PARTS LIST ............................................................................................................. 10
5 NOTES ...................................................................................................................... 12
GB-2
TRI-KING ANTI-VIBRATION KIT
FITTING INSTRUCTION MANUAL
GB
This safety symbol indicates important safety
messages in this manual. When you see this
symbol, be alert to the possibility of injury, carefully
read the message that follows, and inform other
operators.
2.1 OPERATING INSTRUCTIONS
• Ensure that the instructions in this book
are read and fully understood.
• No person should be allowed to operate
this machine unless they are fully
acquainted with all the controls and the
safety procedures.
• Never allow children or people unfamiliar
with these instructions to use this
machine. Local regulations may restrict
the age of the operator.
2.2 SAFETY SIGNS
• It is essential all safety labels are kept
legible, if they are missing or illegible they
must be replaced. If any part of the
machine is replaced and it originally
carried a safety label, a new label must be
affixed to the replacement part. New
safety labels are obtainable from
Ransomes dealers.
2.3 STARTING THE ENGINE
• Before starting the engine check that the
brakes are applied, drives are in neutral,
guards are in position and intact, and
bystanders are clear of the machine.
• Do not run the engine in a building without
adequate ventilation.
2.4 DRIVING THE MACHINE
• Before moving the machine, check to
ensure that all parts are in good working
order, paying particular attention to
brakes, tyres, steering and the security of
cutting blades.
• Replace faulty silencers, mow only in
daylight or good artificial light
• Always observe the Highway Code both on
and off the roads. Keep alert and aware at
all times. Watch out for traffic when
crossing or near roadways.
• Stop the blades rotating before crossing
surfaces other than grass.
• Remember that some people are deaf or
blind and that children and animals can be
unpredictable.
• Keep travelling speeds low enough for an
emergency stop to be effective and safe at
2 SAFETY INSTRUCTIONS
all times, in any conditions.
• Remove or avoid obstructions in the area to
be cut, thus reducing the possibility of injury
to yourself and/or bystanders.
• When reversing, take special care to ensure
that the area behind is clear of obstructions
and/or bystanders. DO NOT carry
passengers.
• Keep in mind that the operator or user is
responsible for accidents or hazards
occurring to other people or their property.
• When the machine is to be parked, stored
or left unattended, lower the cutting means
unless the transport locks are being used.
• While mowing, always wear substantial
footwear and long trousers. Do not operate
the equipment when barefoot or wearing
open sandals.
• Check the grass catcher frequently for wear
or deterioration. After striking a foreign
object. Inspect. the lawnmower for damage
and make repairs before restarting and
operating the equipment.
• If the machine starts to vibrate abnormally,
check immediately.
2.5 TRANSPORTING
• Ensure that the cutting units are securely
fastened in the transport position. Do not
transport with cutting mechanism rotating.
• Drive the machine with due consideration of
road and surface conditions, inclines and
local undulations.
2.6 LEAVING THE DRIVING POSITION
• Park the machine on level ground.
• Before leaving the driving position, stop the
engine and make sure all moving parts are
stationary. Apply brakes and disengage all
drives. Remove the starter key.
2.7 SLOPES
TAKE EXTRA CARE WHEN WORKING ON
SLOPES
• Local undulations and sinkage will change
the general slope. Avoid ground conditions
which can cause the machine to slide.
• Keep machine speeds low on slopes and
during tight turns.
• Remember there is no such thing as a
“safe” slope.
• Travel on grass slopes requires particular
care.
GB-3
TRI-KING ANTI-VIBRATION KIT
FITTING INSTRUCTION MANUAL
GB
Hydraulic Fluid escaping under
pressure can penetrate skin and do
serious damage. Immediate medical
assistance must be sought.
WARNING
2.8 BLOCKED CUTTING CYLINDERS
• Stop the engine and make sure all moving
parts are stationary.
• Apply brakes and disengage all drives.
• Release blockages with care. Keep all parts
of the body away from the cutting edge.
Beware of energy in the drive which can
cause rotation when the blockage is released.
• Keep other people away from the cutting units
as rotation of one cylinder can cause the
others to rotate.
2.9 ADJUSTMENTS, LUBRICATION AND
MAINTENANCE
• Stop the engine and make sure all moving
parts are stationary.
• Apply brakes and disengage all drives.
• Read all the appropriate servicing instructions.
• Use only the replacement parts supplied by
the original manufacturer.
• When adjusting the cutting cylinders take
care not to get hands and feet trapped when
rotating cylinders.
• Make sure that other people are not touching
any cutting units, as rotation of one cylinder
can cause the others to rotate.
• To reduce the fire hazard, keep the engine,
silencer and battery compartments free of
grass, leaves or excessive grease.
• Replace worn or damaged parts for safety.
• When working underneath lifted parts or
machines, make sure adequate support Is
provided.
• Do not dismantle the machine without
releasing or restraining forces which can
cause parts to move suddenly.
DANGER - Indicates an imminently hazardous
situation which, if not avoided, WILL result in death
or serious injury.
WARNING - Indicates a potentially hazardous
situation which, if not avoided, COULD result in
death or serious injury.
CAUTION - Indicates a potentially hazardous
situation which, if not avoided, MAY result in minor
or moderate injury and property damage. It may
also be used to alert against unsafe practices.
2 SAFETY INSTRUCTIONS
Batteries produce explosive gases and
contain corrosive acid and supply levels
of electrical current high enough to cause
burns.
WARNING
DISCONNECT THE BATTERY
BEFORE WORKING ON THE ELECTRICS
WARNING
Battery posts, terminals and related
accessories contain lead and lead
compounds
WASH HANDS AFTER HANDLING
WARNING
GB-4
TRI-KING ANTI-VIBRATION KIT
FITTING INSTRUCTION MANUAL
GB
3 FITTING INSTRUCTIONS
3.2 Open and remove the Engine and steering
Tower Covers from the machine.
3.3 Disconnect the three flexable hydraulic
hoses from the steering motor.
Remembering to note which flexable
hydraulic hose conects to which port of
the steering motor.
Remove the two steel hydraulic hoses
from the steering motor, hydraulic pump &
filter.
3.4 Remove the U bolt marked A from around
the steering column and the control
pannel.
Remove the screws holding the bottom of
the control pannel to the machines frame.
This will alow the control pannel to hang
on the steering column.
NOTE: you may have to disconect some
of the Instruments to ease assembly of the
Anti-Vibration Kit.
3.1 Make sure that the machine is parked on
flat, level ground, with the parking brake on
and lower the cutting units.
Disconnect the Negative terminal on the
battery.
AUX
OUT IN
LT
RT
E
A
D
B
C
A
GB-5
TRI-KING ANTI-VIBRATION KIT
FITTING INSTRUCTION MANUAL
GB
3 FITTING INSTRUCTIONS
3.5 Remove the four nuts and washers from
the top of the steering motor .
This will alow the steering motor to be just
supported by the steering tower of the
machine.
Remove the fuse block from the Steering
Tower.
3.6 Place the Anti-Vibration Plate A (Item 1)
& the Dashboard Bracket (Item 8) onto
the top of the steering tower.
Using the Screws M8x25 (Item 15),
Washers M8 (Item 19) & Nuts - Nyloc M8
(Item18) Fasten the Anti-Vibration Plate A
(Item 1) onto the steering tower and the
Dashboard Backet (Item 8) onto the Anti-
Vibration Plate A (Item 1).
GB-6
TRI-KING ANTI-VIBRATION KIT
FITTING INSTRUCTION MANUAL
GB
3 FITTING INSTRUCTIONS
3.7 Insert the two Anti-Vibration Plate B (Item
2) between the Anti-Vibration Plate A
(Item 1) and the Steering Pump.
Using the original Washers and Nuts
fasten the Anti-Vibration Plate B (Item 2)
to the Steering Pump.
3.8 Place the Isolation Mounts (Item 22)
between the Anti-Vibration Plate A (Item
1) & the Anti-Vibration Plate B (Item 2),
with the male thread facing upwards.
Fasten the male threaded end of the
Isolation Mounts (Item 22) to the Anti-
Vibration Plate B (Item 2) with Plain
Washer M8 (Item 19), Spring Washer M8
(Item 20) & Nut M8 (Item17).
Fasten the female threaded end of the
Isolation mount (Item 22) to the Anti-
Vibration Plate A (Item 1) with Plain
Washer M8 (Item 19), Nut M8 (Item 17) &
Screw M8x30 (Item 16).
When tightening up the Screws M8x30
(Item 16) screw in to the Isolation Mount
(Item 22) finger tight. Then using a
spanner turn the Screw (Item 16) a
quarter turn to nip it up. Then holding the
Screw M8x30 (Item 16) still with the
spanner tighten up the Nut M8 (Item 17).
GB-7
TRI-KING ANTI-VIBRATION KIT
FITTING INSTRUCTION MANUAL
GB
3 FITTING INSTRUCTIONS
3.9 Bolt the Fuse Holder (Item 3) onto the
Anti-Vibration Plate A (Item 1) with the
Washer (Item 10), Spring Washer
(Item11) & Screw M6x25 (Item 13).
Then fasten the Fuse Block onto the Fuse
Holders (Item 3) using the original
fasteners.
Bolt the control pannel onto the Dashboard
Bracket (Item 8) with the Screw M8x25
(Item 15), Washer M8 (Item 19) & Nut M8
Nyloc (Item 18).
Refasten the bottom of the control pannel
back onto the machines frame and
reconect any of the instruments that have
been disconected.
3.10 Replace the Three Flexable Hydraulic
Pipes back onto their original ports on the
steering pump.
Using the Flexable Hydraulic Pipe (Item 7)
connect the straight conection onto port A
of the steering pump. Then connect the 90
Deg connector onto the hydraulic pump
port A and tighten both connections.
Using the Flexable Hydraulic Pipes (Item
6), connect one of the straight connections
onto port B of the steering pump. Then
connect the other straight conector onto
the filter assembly port B and tighten both
connections.
Top up the hydraulic oil with the
recomended oil and level that is stated in
your operators manual.
A
B
B
A
6
7
7
GB-8
TRI-KING ANTI-VIBRATION KIT
FITTING INSTRUCTION MANUAL
GB
3 FITTING INSTRUCTIONS
3.12 Place the Foot Support Bracket (Item 4)
at a comfitable position on the foot plate
for the operator.
Mark & drill two 9 dia holes 30mm apart
and remove any burrs from the foot plate.
Bolt the Foot Support Bracket (Item 4)
onto the foot plate using the screw M8x25
(Item 15), Washer M8 (Item 19) & Nut M8
Nyloc (Item 18), Push the Pedal Grip
(Item 23) onto the Foot Support Bracket
(Item 4).
3.13 Replace the negative terminal back onto
the battery.
Start the machine up to check for any
hydraulic leaks.
Replace the Engine and steering Tower
Covers onto the machine & secure them
into position.
3.11 Looking at the radiator from the right hand
side wheel, remove the bottom radiator
fixing bolt.
Using Screw Hex M6x16 (Item 12),
Washer M8 (Item 10) & Spring Washer
(Item 11), bolt the Pipe Supprot Bracket
(Item 5) to the bottom radiator fixing.
Sit the hydraulic pipes into the Pipe
Support Bracket (Item 5), using a Nylon
Tie (Item 24) tie the two hydraulic hoses
to the Pipe Support Bracket (Item 5).
5
24
4, 15, 18, 19 & 23
GB-9
TRI-KING ANTI-VIBRATION KIT
FITTING INSTRUCTION MANUAL
GB
GB-10
TRI-KING ANTI-VIBRATION KIT
FITTING INSTRUCTION MANUAL
GB
4 PARTS
GB-11
TRI-KING ANTI-VIBRATION KIT
FITTING INSTRUCTION MANUAL
GB
4 PARTS
ITEM RANSOMES DESCRIPTION QTY REMARKS
PART NO
LMAC020 Anti-Vibration Kit
1 4120842 Steering Vibration Plate A 1
2 4120843 Steering Vibration Plate B 2
3 4121389 Fuse Holder W/A 1
4 4121502 Foot Support 1
5 4121503 Pipe Support 1
6 4121422 Hose - 11/16" ORFS F - F x 715LG 1
7 4121423 Hose - 11/16" ORFS F `13/16" 1
ORFS F - 13/16" ORFS 90Fx760LG
8 4120596 Dashboard Bracket 1
10 450389 Washer - M6 x 12.5 x 1.8 3
11 450410 Lockwasher - M6 x 9.6 x 1.5 3
12 450170 Screw - Hex M6 x 16 1
13 450172 Screw - Hex M6 x 25 2
15 450192 Screw - Hex M8 x 25 8
16 450193 Screw - Hex M8 x 30 4
17 450324 Nut - Hex M8 8
18 450378 Nut - Hex M8 Nyloc 8
19 450390 Washer - M8 x 17 x 1.8 24
20 450411 Lockwasher - M8 x 12.75 x 2 4
22 4121539 Vibration Isolation Mounts 4
23 3003475 Pedal Grip 1
24 001992032 Nylon Tie 1
GB-12
TRI-KING ANTI-VIBRATION KIT
FITTING INSTRUCTION MANUAL
GB
NOTES
8 NOTES
BOB-CAT BUNTON CUSHMAN JACOBSEN RANSOMES RYAN
Equipment from Textron Turf Care and Specialty
Products is built to exacting standards ensured by
ISO 9001 registration at all our manufacturing locations.
A worldwide dealer network and factory-trained
technicians backed by Textron Parts Xpress provide
reliable, high-quality product support.
Ransomes Jacobsen Limited 1999
Central Avenue, Ransomes Europark,
Ipswich, England, IP3 9QG
English Company Registration No. 1070731
www.textronturf.com
World Class Quality, Performance and Support
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Ransomes 67042, 67043 Accessories Manual
- Category
- Engine
- Type
- Accessories Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ransomes 24834 Accessories Manual
-
-
-
Ransomes Greens King V Plus User manual
-
-
Ransomes 67146 Installation guide
-
-
-
-
