AGI Wide Corr Inside Ladder Installation guide

AGI
Brand
AGI
Model
Wide Corr Inside Ladder
Type
Installation guide
Read this manual before using product. Failure to
follow instructions and safety precautions can
result in serious injury, death, or property
damage. Keep manual for future reference.
Part Number: 198932 R6
Revised: Nov. 2018
Inside Ladder
Wide-Corr® Grain Bin
Installation and Storage Instructions
Original Instructions
New in this Manual
The following changes have been made in this revision of the manual:
Description Section
Updated Safety Decal Locations 2.6. Safety Decal Locations and Details on page 7
INSIDE LADDER – WIDE-CORR® GRAIN BIN
198932 R6 3
CONTENTS
1. Introduction ............................................................................................................................................ 4
2. Safety....................................................................................................................................................... 5
2.1. Safety Alert Symbol and Signal Words..................................................................................... 5
2.2. General Product Safety ............................................................................................................ 5
2.3. Personal Protective Equipment................................................................................................ 5
2.4. Safety Decals ............................................................................................................................ 6
2.5. Decal Installation/Replacement ............................................................................................... 6
2.6. Safety Decal Locations and Details .......................................................................................... 7
3. Before You Begin .................................................................................................................................. 10
3.1. Bin Design and Capacity......................................................................................................... 10
3.2. Foundation Design and Loads ................................................................................................ 10
3.3. Site and Assembly .................................................................................................................. 10
3.4. Methods of Installation .......................................................................................................... 11
3.5. Critical Assembly Requirements ............................................................................................ 11
3.6. Product Storage...................................................................................................................... 12
3.7. Grain Bin Use.......................................................................................................................... 13
3.8. Ladder-Stair Usage ................................................................................................................. 13
3.9. Important Notes ..................................................................................................................... 14
4. Preparation ........................................................................................................................................... 15
4.1. Check Shipment...................................................................................................................... 15
4.2. List of Tools and Equipment................................................................................................... 15
4.3. Order Optional Equipment..................................................................................................... 15
5. Assembly ............................................................................................................................................... 16
5.1. Assembly Safety ..................................................................................................................... 16
5.2. Inside Ladder Installation ....................................................................................................... 17
6. Appendix ............................................................................................................................................... 18
6.1. Inside Ladder Parts List .......................................................................................................... 18
6.2. Inside Ladder Hardware Package - 234548 ........................................................................... 18
7. Limited Warranty: Westeel Grain Bin Products .................................................................................. 19
4 198932 R6
1. Introduction
This manual describes how to assemble a Westeel Wide-Corr® Grain Bin.
Before assembling the inside ladder, please read this manual. Familiarize yourself with the process and
the necessary precautions for efficient and safe assembly.
Everyone present at the assembly site is required to be familiar with all safety precautions.
Keep this manual available for frequent reference and review it with new personnel. Call your local
distributor or dealer if you need assistance or additional information.
1. INTRODUCTION INSIDE LADDER – WIDE-CORR® GRAIN BIN
198932 R6 5
2. Safety
2.1. Safety Alert Symbol and Signal Words
This safety alert symbol indicates important safety messages in this manual. When you see
this symbol, be alert to the possibility of injury or death, carefully read the message that
follows, and inform others.
Signal Words: Note the use of the signal words DANGER,WARNING,CAUTION, and NOTICE with the safety
messages. The appropriate signal word for each message has been selected using the definitions below as a
guideline.
Indicates an imminently hazardous situation that, if not avoided, will result in serious injury or
death.
Indicates a hazardous situation that, if not avoided, could result in serious injury or death.
Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury.
Indicates a potentially hazardous situation that, if not avoided, may result in property damage.
2.2. General Product Safety
YOU are responsible for the SAFE use and maintenance of your inside ladder. YOU must ensure that you and
anyone else who is going to work around the inside ladder understands all procedures and related SAFETY
information contained in this manual.
Remember, YOU are the key to safety. Good safety practices not only protect you, but also the people around
you. Make these practices a working part of your safety program. All accidents can be avoided.
• It is the inside ladder owner, operator, and maintenance personnel's responsibility
to read and understand ALL safety instructions, safety decals, and manuals and
follow them when operating, or maintaining the equipment.
• Owners must give instructions and review the information initially and annually with all personnel before
allowing them to operate the inside ladder. Untrained users/operators expose themselves and bystanders to
possible serious injury or death.
• The inside ladder is not intended to be used by children.
• Use the inside ladder for its intended purposes only.
• Do not modify the inside ladder in any way without written permission from the manufacturer.
Unauthorized modification may impair the function and/or safety, and could affect the life of the inside
ladder. Any unauthorized modification will void the warranty.
2.3. Personal Protective Equipment
The following Personal Protective Equipment (PPE) should be worn when installing the equipment.
INSIDE LADDER – WIDE-CORR® GRAIN BIN 2. SAFETY
6 198932 R6
Safety Glasses
• Wear safety glasses at all times to protect eyes from debris.
Coveralls
• Wear coveralls to protect skin.
Hard Hat
• Wear a hard hat to help protect your head.
Steel-Toe Boots
• Wear steel-toe boots to protect feet from falling debris.
Work Gloves
• Wear work gloves to protect your hands from sharp and rough edges.
2.4. Safety Decals
• Keep safety decals clean and legible at all times.
• Replace safety decals that are missing or have become illegible. See decal location figures that follow.
• Replaced parts must display the same decal(s) as the original part.
• Replacement safety decals are available free of charge from your distributor, dealer, or factory as applicable.
2.5. Decal Installation/Replacement
1. Decal area must be clean and dry, with a temperature above 50°F (10°C).
2. Decide on the exact position before you remove the backing paper.
3. Align the decal over the specified area and carefully press the small portion with the exposed sticky backing
in place.
4. Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in place.
5. Small air pockets can be pierced with a pin and smoothed out using the sign backing paper.
2. SAFETY INSIDE LADDER – WIDE-CORR® GRAIN BIN
198932 R6 7
2.6. Safety Decal Locations and Details
Replicas of the safety decals that are attached to the inside ladder and their messages are shown in the figure(s)
that follow. Safe operation and use of the inside ladder requires that you familiarize yourself with the various
safety decals and the areas or particular functions that the decals apply to, as well as the safety precautions
that must be taken to avoid serious injury, death, or damage.
Figure 1. Safety Decals
INSIDE LADDER – WIDE-CORR® GRAIN BIN 2. SAFETY
8 198932 R6
• Read operator’s manual and all safety decals
before assembling, using, or servicing bin.
• Close/latch all access doors when not in use.
• Do not alter or modify bin structure.
• Replace any damaged components only with
factory made components.
• This bin should only be used to store free
flowing, granular material, unless specifically
designed and marked otherwise.
• When filling, use top filler cap and direct
material to center of bin.
• Do not over-fill bin. Material should not be in
contact with or place pressure on roof sheets.
SAFETY INSTRUCTIONS
WARNING
Part Number: 8110–00012
WARNING
Never enter the bin when loading or
unloading grain.
If you must enter the bin:
1. Shut off and lock out all power.
2. Use a lifeline, safety harness, and have an
observer outside before entering the bin.
3. Wear proper breathing equipment or a respirator.
4. Avoid the center of the bin.
Failure to heed these warnings could result
in serious injury or death.
ENTRAPMENT HAZARD
Part Number: 8110–00013
WARNING
Keep clear of all augers. DO NOT ENTER this bin!
If you must enter the bin:
1. Shut off and lock out all power.
2. Use a safety harness and safety line.
3. Station another person outside the bin.
4. Avoid the center of the bin.
5. Wear proper breathing equipment or respirator.
Failure to heed these warnings could result in serious injury or death.
Rotating flighting could
kill or dismember.
Flowing material could
trap and suffocate.
Crusted material could
collapse and suffocate.
Part Number: 8110–00112
2. SAFETY INSIDE LADDER – WIDE-CORR® GRAIN BIN
198932 R6 9
To prevent serious
injury or death:
• Do not climb ladder if
damaged, wet, icy,
greasy, or slippery.
• Maintain good
balance by having at
least three points of
contact at all times.
FALLING HAZARD
WARNING
Part Number: 8110–00136
When equipped with aeration system, to
prevent roof and/or bin damage:
• Consult dealer to install adequate roof venting.
• Ensure all roof vents are open and unobstructed.
• Discontinue use of aeration fan if roof vents
become obstructed with ice.
NOTICE
Part Number: 8110–00066
FALL RESTRAINT
ANCHOR POINT
MAX WORKING LOAD:
1,000 lb [453 kg]
SEE MANUFACTURER ROOF MANUAL FOR
DETAILED INSTRUCTIONS REGARDING
ANCHOR POINT LOCATIONS
Part Number: 8110–01090
INSIDE LADDER – WIDE-CORR® GRAIN BIN 2. SAFETY
10 198932 R6
3. Before You Begin
3.1. Bin Design and Capacity
These Westeel Grain Bins are designed for:
1. Non-corrosive free-flowing materials up to 55 lbs/ft3(880 kg/m3) average compacted bulk density.
2. Maximum horizontal gusted wind speed of 94 mph (151 km/h)
3. Seismic zone 2a (U.B.C. 1997).
4. Roof Loading
Snow Load Peak Load
15’ — 24’ bins 27’ — 48’ bins
Imperial Metric Imperial Metric Imperial Metric
15.0 lbs/ft2.72 kPa
4000 lbs. 17.8 kN 5000 lbs. 22.2 kN
24.0 lbs/ft2
(when optional roof
stiffening rings
installed)
1.15 kPa
(when optional roof
stiffening rings
installed)
3.2. Foundation Design and Loads
The foundations for the stiffened bin models are based on 4000 lbs. per sq. ft. (192 kPa) soil bearing capacity.
All foundation designs use 3000 lbs. per sq. in. (21 MPa) ultimate compressive strength (after 28 days) for
concrete and 43,500 lbs. per sq. in. (300 MPa) re-bar. The foundation designs included in this manual are
suggestions only, and will vary according to local soil conditions. Westeel will not assume any liability for results
arising from their use.
Important
Foundation should be uniform and level. Level should not vary by more than ¼" over a span of four feet
under the bottom ring angle. Any variance from level must be shimmed under upright base assembly. If
being utilized to support a full floor aeration system, this levelness requirement should extend across
the complete floor area.
3.3. Site and Assembly
Unless otherwise specifically provided in writing, Westeel does not take responsibility for any defects or
damages to any property, or injury to any persons, arising from or related to any site or assembly
considerations, including but not limited to:
• Bin location and bin siting
• Soil conditions and corresponding foundation requirements (note that the examples provided in manuals
are for specifically stated soil conditions)
• Bin assembly (Westeel recommends the use of qualified bin installers; contact Westeel for information on
installers in your area)
• Field modifications or equipment additions that affect the bin structure
• Interconnections with neighboring structures
3. BEFORE YOU BEGIN INSIDE LADDER – WIDE-CORR® GRAIN BIN
198932 R6 11
• Compliance with all applicable safety standards, including but not limited to fall restraint systems (ladders or
other systems). Local safety authorities should be contacted as standards vary between jurisdictions.
3.4. Methods of Installation
The recommendations for assembling and installing Westeel grain bins must be closely followed to achieve the
full strength of the bin and to achieve adequate weather sealing. The product warranty is void if:
1. Wall sheets and/or uprights not specified for a given tier are used.
2. Foundations are found to be inadequate or out-of-level.
3. Anchor bolts (cast-in-place, drill-in, chemical type or other) are found to be inadequate.
4. Off-center loading or unloading is used. (This does not apply to the use of approved side unloading systems.)
5. Materials stored are not free-flowing or have a compacted bulk density greater than 55 lbs/ft3(880 kg/m3).
If using bin jacks during assembly, always lift on an upright. Choose a hoist with a adequate capacity for the
expected empty bin deadload. Make sure the rated capacity of the hoist is not exceeded.
3.5. Critical Assembly Requirements
To ensure a successful, safe and reliable outcome you must comply with the following assembly techniques and
practices:
1. Comply with all local code and jurisdictional requirements applicable to your inside ladder installation.
2. Design and build foundations with the necessary strength for the loads they must support, and for local soil
conditions. Westeel foundation guidelines are based on specific stated conditions and may not be applicable
to local conditions.
3. Your foundation must provide uniform and level support to the structure being supported. Surface
imperfections causing gapping must be remedied. This may involve, but not be limited to a) grouting under
the bottom ring of a non-stiffened bin or tank, and b) shimming under the uprights of a stiffened bin or
tank, or under the legs of a hopper.
4. Make sure that the proper hardware is utilized for all bolted connections. If a shortage occurs, do not
substitute. Take the necessary steps to obtain the proper hardware. Make sure nuts are tightened to the
required torque values as specified in the appropriate assembly manual.
5. Comply with all assembly instructions provided in the appropriate assembly manual to make sure your
whole inside ladder is constructed safely. Important: Do not deviate from the wall sheet and upright
layouts provided.
6. Before anchoring your structure to its foundation, make sure the structure is round. The maximum variation
from perfect roundness is 3/4" on the radius. Locate anchor bolts toward the outside of the anchor bolt
holes (away from the circle) to permit the incremental expansion that can occur with the initial filling.
7. When installing roof stiffening rings, if it is necessary to shorten the stiffening ring tubes, shorten them as
little as possible. Initially the nuts on the expanders should be centered and as close together as possible.
When tightening, share the amount of take-up between expanders such that the nuts remain centered, and
the amount of engagement between all expanders on the same ring is equalized.
8. If extending an existing bin or tank, ensure that the foundation is adequate for the increased loads it must
support.
INSIDE LADDER – WIDE-CORR® GRAIN BIN 3. BEFORE YOU BEGIN
12 198932 R6
9. If installing an existing bin on a hopper, make sure the bin is designed for a hopper application, and that the
foundation is capable of withstanding the substantial point loads that the hopper legs apply. If uprights are
present, make sure that they are supported.
10. Make sure that an integral end-to-end connection exists between all mating uprights. Successive uprights
must not overlap.
11. Vertical tolerances between uprights and wall sheets are tight. This can be affected by “jacking” techniques,
which can allow the tolerance to grow or shrink depending on the technique used. The gapping between
successive uprights must be monitored to ensure that upright holes align with wall sheet holes.
12. If catwalks are being installed on the structure, upright catwalk upgrades are likely required. The upgraded
stiffeners must be installed in the correct locations to support the intended catwalk loads. Also, the
structure must be properly oriented to ensure the eventual correct alignment between the catwalks and the
supporting uprights. Finally, the connectors that tie into the uprights and support the catwalks are best
installed during assembly of the structure. See the catwalk assembly manual for additional details.
3.6. Product Storage
Rust on Galvanized Parts
1. White rust forms when moisture is allowed to collect on galvanized surfaces that have yet to develop the
durable zinc oxide layer. This zinc oxide layer naturally occurs as the surface interacts with carbon dioxide,
and is characterized over time by the dull grey appearance that weathered galvanized surfaces get.
2. Parts that are not well ventilated or well drained can collect water between surfaces and develop white rust.
3. White rust is not a structural concern if its development is stopped in the early stages. A light film or
powdery residue can occur after a period of heavy rainfall or a short time of improper storage. If white rust
has started to develop, separate parts and wipe off any moisture. Next, using a clean cloth, apply a thin
layer of petroleum jelly or food-grade oil to the entire part.
4. If moisture is left on parts, this white rust can become more aggressive and turn into red rust. Red rust can
cause degradation in the material and become a structural concern. Any parts that have red rust should be
replaced immediately.
Storage Guidelines
• Keep all bundles dry before assembly of the bin.
• Start assembly as soon as possible.
• Do not lay bundles on the bare ground. Raise all bundles 6" to 8" off the ground on wood blocks or timbers.
(See Detail A in Figure 2 on page 13.)
• Store curved wall sheets ‘hump-up’. (See Detail A in Figure 2 on page 13.)
• All other bundles material should be placed so that they are well sloped to promote good drainage. (See
Detail B in Figure 2 on page 13.)
• Roof sheets must be elevated at least 12" at the small end of the sheets. (See Detail B in Figure 2 on page
13.)
• Temporary storage can be provided by erecting a simple framework supporting a waterproof tarp. (See
Detail C in Figure 2 on page 13.)
• All bin boxes, ladder boxes and hardware boxes should be stored inside. These are not waterproof, and will
deteriorate in normal weather conditions, allowing moisture to contact the parts inside.
3. BEFORE YOU BEGIN INSIDE LADDER – WIDE-CORR® GRAIN BIN
198932 R6 13
Figure 2. Product Storage
3. White rust is not a structural concern if its development is stopped in the early stages. A
light film or powdery residue can occur after a period of heavy rainfall or a short time of
improper storage. If white rust has started to develop, separate parts and wipe off any
moisture. Next, using a clean cloth, apply a thin layer of petroleum jelly or food-grade oil
to the entire part.
4. If moisture is left on parts, this white rust can become more aggressive and turn into red
rust. Red rust can cause degradation in the material and become a structural concern.
Any parts that have red rust should be replaced immediately.
Storage Guidelines
1. Keep all bundles dry before assembly of the
bin. Start assembly as soon as possible. Do not
lay bundles on the bare ground, raise all bundles
6” – 8” off the ground on wood blocks or timbers.
Store curved wall sheets ‘hump-up’. All other
bundles material should be placed so that they are
well sloped to promote good drainage.
2. Roof sheets must be elevated at least 12” at the
small end of the sheets.
3. Temporary storage can be provided by erecting
a simple framework supporting a waterproof tarp.
4. All bin boxes, ladder boxes and hardware boxes should be stored inside. These are not
waterproof, and will deteriorate in normal weather conditions, allowing moisture to contact
the parts inside.
If Parts Become Wet
1. If goods become submerged or wet, the
bundles should be opened as soon as possible,
sheets or material separated and dried. Keep
separated until assembly. Brace goods
properly so as to avoid damage or injury from
material falling when in storage.
2. Any boxed goods that become wet should be dried and stored in a new box that is free of
moisture.
3. In addition to wiping down wallsheets, a food-grade oil can also be applied with a clean,
lint-free cloth. This will assist in preventing any further moisture from contacting the
galvanizing on the steel. Due to safety concerns with installation and use, Westeel does
not recommend the use of oil on other parts such as roof sheets and safety ladders.
Page A10
A
3. White rust is not a structural concern if its development is stopped in the early stages. A
light film or powdery residue can occur after a period of heavy rainfall or a short time of
improper storage. If white rust has started to develop, separate parts and wipe off any
moisture. Next, using a clean cloth, apply a thin layer of petroleum jelly or food-grade oil
to the entire part.
4. If moisture is left on parts, this white rust can become more aggressive and turn into red
rust. Red rust can cause degradation in the material and become a structural concern.
Any parts that have red rust should be replaced immediately.
Storage Guidelines
1. Keep all bundles dry before assembly of the
bin. Start assembly as soon as possible. Do not
lay bundles on the bare ground, raise all bundles
6” – 8” off the ground on wood blocks or timbers.
Store curved wall sheets ‘hump-up’. All other
bundles material should be placed so that they are
well sloped to promote good drainage.
2. Roof sheets must be elevated at least 12” at the
small end of the sheets.
3. Temporary storage can be provided by erecting
a simple framework supporting a waterproof tarp.
4. All bin boxes, ladder boxes and hardware boxes should be stored inside. These are not
waterproof, and will deteriorate in normal weather conditions, allowing moisture to contact
the parts inside.
If Parts Become Wet
1. If goods become submerged or wet, the
bundles should be opened as soon as possible,
sheets or material separated and dried. Keep
separated until assembly. Brace goods
properly so as to avoid damage or injury from
material falling when in storage.
2. Any boxed goods that become wet should be dried and stored in a new box that is free of
moisture.
3. In addition to wiping down wallsheets, a food-grade oil can also be applied with a clean,
lint-free cloth. This will assist in preventing any further moisture from contacting the
galvanizing on the steel. Due to safety concerns with installation and use, Westeel does
not recommend the use of oil on other parts such as roof sheets and safety ladders.
Page A10
B
3. White rust is not a structural concern if its development is stopped in the early stages. A
light film or powdery residue can occur after a period of heavy rainfall or a short time of
improper storage. If white rust has started to develop, separate parts and wipe off any
moisture. Next, using a clean cloth, apply a thin layer of petroleum jelly or food-grade oil
to the entire part.
4. If moisture is left on parts, this white rust can become more aggressive and turn into red
rust. Red rust can cause degradation in the material and become a structural concern.
Any parts that have red rust should be replaced immediately.
Storage Guidelines
1. Keep all bundles dry before assembly of the
bin. Start assembly as soon as possible. Do not
lay bundles on the bare ground, raise all bundles
6” – 8” off the ground on wood blocks or timbers.
Store curved wall sheets ‘hump-up’. All other
bundles material should be placed so that they are
well sloped to promote good drainage.
2. Roof sheets must be elevated at least 12” at the
small end of the sheets.
3. Temporary storage can be provided by erecting
a simple framework supporting a waterproof tarp.
4. All bin boxes, ladder boxes and hardware boxes should be stored inside. These are not
waterproof, and will deteriorate in normal weather conditions, allowing moisture to contact
the parts inside.
If Parts Become Wet
1. If goods become submerged or wet, the
bundles should be opened as soon as possible,
sheets or material separated and dried. Keep
separated until assembly. Brace goods
properly so as to avoid damage or injury from
material falling when in storage.
2. Any boxed goods that become wet should be dried and stored in a new box that is free of
moisture.
3. In addition to wiping down wallsheets, a food-grade oil can also be applied with a clean,
lint-free cloth. This will assist in preventing any further moisture from contacting the
galvanizing on the steel. Due to safety concerns with installation and use, Westeel does
not recommend the use of oil on other parts such as roof sheets and safety ladders.
Page A10
C
Page A10
If Parts Become Wet
1. If parts become submerged or wet, the bundles should be opened as soon as possible, sheets or material
separated and dried. Keep separated until assembly.
Brace parts properly so as to avoid damage or injury from material falling when in storage. (See Detail D in
Figure 2 on page 13.)
2. Any boxed parts that become wet should be dried and stored in a new box that is free of moisture.
3. In addition to wiping down wall sheets, a food-grade oil can also be applied with a clean, lint-free cloth. This
will assist in preventing any further moisture from contacting the galvanizing on the steel. Due to safety
concerns with installation and use, Westeel does not recommend the use of oil on other parts such as roof
sheets and safety ladders.
3.7. Grain Bin Use
• Do not off-center unload a grain bin. It is imperative to unload from the center of the bin first, until as much
grain as possible has been removed, and only then proceed to unload from the next closest unload gate to
the center. Continue utilizing the unload gates in succession from the center towards the outside. Gate
control mechanisms should be clearly marked and interconnected to prevent an external gate from being
opened first.
• The only exception to center unloading is when a properly designed and installed side draw system is
utilized. However, as bins tend to go out of round when employing side draws, the bin must be completely
emptied before refilling.
• When unloading a bin with a mobile auger through a properly designed auger chute, the entry end of the
auger should be pushed into the center of the bin before the auger is engaged. Slower rates of flow are
preferable and should not exceed the capacity of an 8” auger.
• Ensure that the inner door panels of grain bin doors are completely closed and latched before filling the
grain bin.
• Never enter a loaded grain bin for any reason. Grain can be a killer.
3.8. Ladder-Stair Usage
The WESTEEL Ladder/Stair in grain bin is designed to provide access to the roof for inspection and maintenance
purposes only. Excessive weight can cause component failure. The Ladder/Stair is not designed to support the
transport of heavy apparatus from the ground to the roof. The user should not carry more than 30 lbs of tools
and equipment on his person. No more than one person should stand on the same ladder rung, stair tread or
platform at the same time. No more than two persons should occupy the ladder/staircase at the same time.
INSIDE LADDER – WIDE-CORR® GRAIN BIN 3. BEFORE YOU BEGIN
14 198932 R6
3.9. Important Notes
• Westeel does not provide a foundation design for this product, and is not liable for any damages or injuries
related to inadequately designed or constructed foundations. Customers must contract professional services
for all foundation design and construction work. For information on foundation design requirements, refer
to Section 3.2. – Foundation Design and Loads on page 10.
• In order to maintain your wall sheets in good condition separate sheets and allow air circulation between
them. Store sheets in a dry place. Do not store sheets with sheet ends pointing upwards.
• To keep an even pressure on walls, the bin must always be unloaded from the centre.
• Contact local power officials for minimum power line clearance.
• See Section 3.5. – Critical Assembly Requirements on page 11 for mandatory siting and assembly
requirements.
• Store only non-corrosive, free-flowing materials up to 55 lbs/ft3(800 kg/m3) average compacted density in
Westeel bins.
• Tighten all bolts to the recommended torque settings.
• Do not locate grain bins close to high buildings, which might cause snow to fall onto or build up on the roof
of the grain bin. Consider future expansion and allow space for loading and unloading of the bin. Your dealer
and local government agricultural consultants can help you plan your storage system for maximum
efficiency.
3. BEFORE YOU BEGIN INSIDE LADDER – WIDE-CORR® GRAIN BIN
198932 R6 15
4. Preparation
4.1. Check Shipment
Unload the parts at the assembly site and compare the packing slip to the shipment. Ensure that all items have
arrived and that none are damaged.
Report damaged parts or shortages immediately to the delivering carrier, followed by a confirming letter
requesting inspection by the carrier, if required. Order any replacement parts immediately to ensure that
assembly will not be held up by missing parts. All parts will be charged for and credit will be issued by party at
fault. No credit will be issued if freight bills are signed as received in good condition.
4.2. List of Tools and Equipment
Use quality tools and equipment. Use them safely, and correctly, for their intended use. Tools for this
application should include:
Tools
• Electric or pneumatic (air) impact tools
• Power drill and drill bits
• Sockets (multiple 9/16" and 1/2" sockets recommended)
• Large-pocket carpenter pouch
• 8" (20 cm) metal punches (for aligning bolt holes)
• Step and extension ladders, construction grade
• 6-point wrenches (Imperial, box end)
• Metal-cutting saw suitable for cutting roof rings and wind rings
• Scaffolding
• Centre-post bin stand
• Crane and/or bin jacks
Minimum Recommended Safety Equipment
• A properly-stocked first-aid kit
• Eye, foot, head, and hand protection (safety glasses, steel-toed boots, hard hat, work gloves)
• Cable, chain, or rope to tie-off bin or jacks in case of wind
• Body harness and lifeline (for use where falling hazard exists)
• Ground fault interrupt protected electrical hook-ups
4.3. Order Optional Equipment
Optional equipment such as unloading augers, aeration equipment, anchor bolts, foundation sealant, external
ladders, safety cage and platforms, etc., should all be on site and checked before assembly starts. Plan your
installation in advance. For details, see assembly instruction supplied with optional equipment.
INSIDE LADDER – WIDE-CORR® GRAIN BIN 4. PREPARATION
16 198932 R6
5. Assembly
Before continuing, ensure you have completely read and understood this manual’s
Safety section, in addition to the safety information in the section(s) below.
5.1. Assembly Safety
• Do not take chances with safety. The components can be large, heavy, and hard to handle.
Always use the proper tools, rated lifting equipment, and lifting points for the job.
• Carry out assembly in a large open area with a level surface.
• Always have two or more people assembling the inside ladder.
• Make sure you have sufficient lighting for the work area.
• Tighten all fasteners according to their specifications. Do not replace or substitute bolts,
nuts, or other hardware that is of lesser quality than the hardware supplied by the
manufacturer.
• Stay away from overhead power lines and other obstructions during assembly. Contact with
power lines can cause electrocution.
• Do not work in high winds.
5. ASSEMBLY INSIDE LADDER – WIDE-CORR® GRAIN BIN
198932 R6 17
5.2. Inside Ladder Installation
Part Number: 198932
Revision: 4
WIDE CORR INSIDE LADDER
INSTALLATION AND STORAGE INSTRUCTIONS
THE BOTTOM OF THE LAST
LADDER SEGMENT MAY NEED
TO BE TRIMMED TO FIT
AT THE BOTTOM LOCATION MOVE
THE INSIDE LADDER CLIP UP AT
LEAST 4” TO CLEAR THE BOTTOM
RING ANGLE. DRILL THROUGH THE
WALL SHEET WHERE CONVENIENT
EXISTING HOLE
TOP WALL SHEET TIER
TOP LADDER SEGMENT
AT THE TOP LOCATION, MOVE THE INSIDE
LADDER CLIPS DOW N AT LEAST 4” TO CLEAR
THE TOP RING ANGLE. DRILL THROUGH THE
WALL SHEET WHERE CONVENIENT
ROOF
A
A
NOTE:
TO ENSURE PROPER ORIENTATION OF LADDER,
LINE UP THE BOTTOM OF THE FIRST LADDER
SEGMENT WITH THE BOTTOM OF THE TOP WALL
SHEET TIER AS SHOWN. ALIGN THE CENTER
HOLE OF THE CLIP WITH THE EXSISTING HOLE
LOCATIONS IN THE HORIZONTAL WALL SHEET
SEAMS. USE 3/8” x 1½” BOLTS AS SHOWN. THE
BOLTS CAN BE PRE-POSITIONED AND HELD IN
PLACE WITH ONE NUT. THE LADDER CAN BE
ATTACHED LATER USING THE SECOND NUT.
MIN 4”
MIN 4”
3/8” x 1½” BOLT
USE 3/8” x 1” BOLTS TO
SECURE THE LADDER
SEGMENTS TO THE
INSIDE LADDER CLIPS
MOUNT INSIDE LADDER CLIPS
SUCH THAT THE FLANGES
POINT OUTWARDS AS SHOWN.
SECTION A–A
ONCE INSTALLED, THE
FOAM PLUG SHOULD BE
FLUSH WITH THE END OF
THE LADDER RUNG, OR
SLIGHTLY PROTRUDING
APPLY BEAD OF GLUE
ALONG EACH SIDE OF
TAPERED FOAM PLUG
AND INSERT INTO ENDS
OF LADDER RUNGS
FOAM PLUG INSTALLATION
READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY
BEFORE BEGINNING FOUNDATION OR ERECTION
EFFECTIVE DATE: June, 2015
INSIDE LADDER – WIDE-CORR® GRAIN BIN 5. ASSEMBLY
18 198932 R6
6. Appendix
6.1. Inside Ladder Parts List
Table 1. Inside Ladder Parts List
PART NUMBER DESCRIPTION
LADDER
SEGMENTS
INSIDE LADDER
CLIPS FOAM PLUGS GLUE INSIDE LADDER
HARDWARE
234500 234519 234529 234556 234548
234560-4 INSIDE LADDER PACKAGE - 4 TIER 4 10 32 1 1
234560-5 INSIDE LADDER PACKAGE - 5 TIER 5 12 40 2 1
234560-6 INSIDE LADDER PACKAGE - 6 TIER 6 14 48 2 1
234560-7 INSIDE LADDER PACKAGE - 7 TIER 7 16 56 2 1
234560-8 INSIDE LADDER PACKAGE - 8 TIER 8 18 64 2 1
234560-9 INSIDE LADDER PACKAGE - 9 TIER 9 20 72 3 1
234560-10 INSIDE LADDER PACKAGE - 10 TIER 10 22 80 3 1
234560-11 INSIDE LADDER PACKAGE - 11 TIER 11 24 88 3 1
234560-12 INSIDE LADDER PACKAGE - 12 TIER 12 26 96 3 2
234560-13 INSIDE LADDER PACKAGE - 13 TIER 13 28 104 4 2
234560-14 INSIDE LADDER PACKAGE - 14 TIER 14 30 112 4 2
234560-15 INSIDE LADDER PACKAGE - 15 TIER 15 32 120 4 2
234560-16 INSIDE LADDER PACKAGE - 16 TIER 16 34 128 4 2
234560-17 INSIDE LADDER PACKAGE - 17 TIER 17 36 136 5 2
234560-18 INSIDE LADDER PACKAGE - 18 TIER 18 38 144 5 2
234560-19 INSIDE LADDER PACKAGE - 19 TIER 19 40 152 5 2
234560-20 INSIDE LADDER PACKAGE - 20 TIER 20 42 160 5 2
234560-21 INSIDE LADDER PACKAGE - 21 TIER 21 44 168 6 2
234560-22 INSIDE LADDER PACKAGE - 22 TIER 22 46 176 6 2
234560-23 INSIDE LADDER PACKAGE - 23 TIER 23 48 184 6 2
6.2. Inside Ladder Hardware Package - 234548
Table 2. Inside Ladder Hardware Package - 234548
PART NUMBER DESCRIPTION QTY
193797 3/8” x 1 1/2” Hex bolt c/w sealing washer 25
235943 3/8” x 1” Hex bolt c/w sealing washer (Bag of 50) 1
235951 3/8” Nut (Bag of 100) 1
198932 Inside Ladder Instructions 1
6. APPENDIX INSIDE LADDER – WIDE-CORR® GRAIN BIN
198932 R6 19
7. Limited Warranty:
Westeel Grain Bin Products
Westeel – Ag Growth International ("Westeel") warrants products that it has manufactured and/or
that are branded with its name (the "goods") subject to the following terms and limitations, (the
"warranty"):
Duration of Warranty
This warranty will run from the date of purchase from the dealer or distributor, authorized by Westeel.
The duration of the warranty is limited as follows:
Galvanized Bins 5 years
EasyFlow2 24 months
Westeel Fans 36 months
Floors 12 months
Catwalk 12 months
Bulk Feed Tanks 24 months
SeedStor-K Cones
Paint 12 months
Structural 30 months
Elite Cones
Paint 30 months
Structural 10 years
WESTEEL cones
Paint No Warranty
Structural 12 months
Smooth Wall Bins
Paint 60 months
Structural 10 years
Commercial Smooth Wall Bins
Paint 12 months
Structural 10 years
Limitation of Remedies Replacement
Within the warranty period, Westeel will replace the goods and/or original manufactured components
thereof which are found, to Westeel's satisfaction, to be defective. Westeel is not responsible for
direct, indirect, special, consequential, or any other damages of any kind, including personal injury to
any individual, howsoever caused, including caused by transportation of the goods for repair or
replacement.
INSIDE LADDER – WIDE-CORR® GRAIN BIN 7. LIMITED WARRANTY:
WESTEEL GRAIN BIN
PRODUCTS
20 198932 R6
Procedure for Obtaining Service
In the event of a warranty claim, the purchaser must complete any and all information required by
Westeel in order to properly assess or investigate the claim. Westeel will not be responsible for the
removal of any of the goods found to be defective, or transportation charges to and from Westeel's
authorized dealer or distributor, or for installation of any replacement goods and/or parts furnished
under the warranty.
Limitations as to Scope of Warranty
The warranty does not extend to defects or damage caused, in whole or in part, by:
1. use of a kind and/or to a degree not reasonably expected to be made of the goods;
2. improper storage of the goods both prior to and after purchase;
3. damage caused by, or in the course of, installation or assembly;
4. any use of the goods which is not an intended use as specified in Westeel's published product
literature, or otherwise specified by Westeel in writing;
5. any equipment attached to or used in conjunction with the goods;
6. any field modifications or substitutions to original bin components;
7. inadequate ventilation or any other circumstance not in keeping with proper maintenance and/or
use of the goods;
8. Acts of God, accident, neglect or abuse of the goods by the purchaser and/or any other individual
or entity; or
9. Any use or installation inconsistent with Westeel’s Standard Disclaimers.
Limitations as to Manufacturer
The warranty does not cover products sold by Westeel that are not manufactured by Westeel. In those
circumstances, the purchaser is referred to the manufacturer of those products.
Limitation of Implied Warranties and Other Remedies
To the extent allowed by law, neither Westeel nor its dealers, nor any company affiliated with Westeel
makes any warranties, representations, or promises as to the quality, performance, or freedom from
defect of any Product covered by this Warranty.
WESTEEL HEREBY DISCLAIMS, TO THE EXTENT APPLICABLE, ANY AND ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. A PURCHASER’S ONLY REMEDIES IN
CONNECTION WITH THIS WARRANTY ARE THOSE SET FORTH IN THIS WARRANTY. IN NO EVENT WILL
WESTEEL, ITS DEALERS, OR ANY COMPANY AFFILIATED WITH WESTEEL BE LIABLE FOR INCIDENTIAL,
CONSEQUENTIAL OR PUNITIVE DAMAGES.
Some jurisdictions do not allow waivers of certain warranties, so the above waivers may not apply to
you. In that event, any implied warranties are limited in duration to ninety (90) days from delivery of
the products. You may also have other rights which vary from jurisdiction to jurisdiction.
Exclusive Warranty
This warranty is the only warranty provided by Westeel and all other warranties and/or commitments,
whether express or implied and no matter by whom made, statutory or otherwise, are subsumed and
replaced by it and are of no legal effect. If any provision of the warranty is held by a court of
7. LIMITED WARRANTY: WESTEEL GRAIN BIN
PRODUCTS
INSIDE LADDER – WIDE-CORR® GRAIN BIN
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

AGI Wide Corr Inside Ladder Installation guide

AGI
Brand
AGI
Model
Wide Corr Inside Ladder
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents