Now that I’m here you are only one
flat-pack away from transforming
your home.
Hello,
I’ve arrived!
Need help?
Macey 3-in-1 Highchair
NEVER LEAVE THE CHILD UNATTENDED
Thank you for your purchase.
Please follow the instructions below for the correct assembly.
●FOLLOW THE MANUFACTURERS INSTRUCTIONS
●FALLING HAZARD: PREVENT YOUR CHILD FROM CLIMBING ON THE PRODUCT
●THE HARNESS MUST ALWAYS BE USED AND CORRECTLY FITTED – MOST
HIGHCHAIR
INJURIES ARE CAUSED BY FALLS. ONLY USE THE HARNESS PROVIDED WITH
THE PRODUCT.
●POSITION THE HIGHCHAIR AWAY FROM SOLID STRUCTURES, BENCHES AND
FURNITURE SO THE CHILD CANNOT PUSH AGAINST THE ITEM AND CAUSE THE
HIGHCHAIR TO TILT, CAUSING SERIOUS INJURY TO THE CHILD.
●ALWAYSE USE THE HIGHCHAIR ON A FLAT AND HORIZONTAL FLOOR. DO NOT
ELEVATE THE HIGHCHAIR ON ANY STRUCTURE OR TABLE.
●NEVER PLACE THE HIGHCHAIR NEAR HOT SURFACES, DANGER
●OUS LIQUIDS,WINDOW BLINDS OR ELECTRICAL CORDS.
●ONLY USE THE HIGHCHAIR WHEN THE CHILD CAN SIT UP UNAIDED
●SUITABLE FOR A CHILD WEIGHING UP TO MAXIMUM 15KG
●ALWAYS ENGAGE THE LOCKS/BRAKES WHEN THE HIGHCHAIR IS STATIONARY
IMPORTANT! READ CAREFULLY AND
KEEP FOR FUTURE REFERENCE
CLEANING & CARE
●DO NOT USE THE PRODUCT UNLESS ALL COMPONENTS ARE CORRECTLY FITTED
AND ADJUSTED.REGULARLY INSPECT THE HIGHCHAIR FOR MAINTENANCE OF
LOOSE SCREWS ETC.
●DO NOT USE THE HIGHCHAIR IF ANY PART IS BROKEN, TORN OR MISSING.
CONTACT THE MANUFACTURER FOR FURTHER ADVICE.
●WIPE THE HIGHCHAIR CLEAN USING A CLEAN DAMP CLOTH AND SUITABLE COM-
MERCIAL CLEANER DO NOT PLACE THE SEAT COVER OR TRAY IN THE DISHWAHER
OR WASHING MACHINE
DO NOT PLACE THE SEAT COVER OR TRAY IN THE DISHWAHER OR
WASHING MACHINE
ASSEMBLY INSTRUCTIONS
mocka.co.nz I mocka.com.au
Macey 3-in-1 Highchair
ASSEMBLY INSTRUCTIONS
mocka.co.nz I mocka.com.au
Chair seat
Footrest
Transparent tray
Tray
Chair holder
Screw Driver x1
For quicker assembly,we recommend the
use of a power drill on a low-speed setting.
x1
x1
x1
x1
x8
x1
Upper legA/B/C/D)
x4 x4
ABCD
AB C D
Washer Leg coverx8 x4
Down legA/B/C/D)
1
Macey 3-in-1 Highchair
2
B
B
A
A
D
D
C
C
1. Install the 4 pcs of legs by joining the upper legs and down legs
according to the same marks (A+A, B+B, C+C, D+D).
2. Insert 4 pcs of legs in chair holder by 4 screws+ 4 washers.
ABCD legs are same, no position request.
Do not tighten the screws until the foot is installed.
ASSEMBLY INSTRUCTIONS
mocka.co.nz I mocka.com.au
3
Macey 3-in-1 Highchair
4
Instructions:
Make sure that four legs all standing on the floor, and then tighten 4
screws on the top of the legs and 4 screws on the footrest. It can
avoid unstable during the assembling.
3. Insert footrest in 4 pcs of legs by 4 screws+ 4 washers.
The footrest can be double-sided used according to different ages.
When using the other side, the footrest will be adjusted to another
height.
4. Push the tray on chair.
Please check the tray is locked well by button before use.
ASSEMBLY INSTRUCTIONS
mocka.co.nz I mocka.com.au
Macey 3-in-1 Highchair
56
6. Take off tray: Press 1 button in one side to take out the tray a
little.Repeat in the other side.
5. Make sure the both sides buttons of transparent
tray has locked after putting on the chair tray.
ASSEMBLY INSTRUCTIONS
mocka.co.nz I mocka.com.au
Macey 3-in-1 Highchair
Different use for baby at different age
BABY HIGH CHAIR
6 months 3 years
≤15kg (33lbs)
BABY HIGH CHAIR
4 6 years
≤25kg (55lbs)
JUNIOR CHAIR
4 6 years
≤25kg (55lbs)
SMALL CHAIR
6 months 3 years
≤15kg (33lbs)
SMALL CHAIR
4 6 years
≤25kg (55lbs)
SMALL CHAIR
4 6 years
≤25kg (55lbs)
High chair changes to high chair without tray :
Baby high chair changes to junior stool
The way to change high chair to small chair:
High chair Small chair
Baby high
chair
2.Take off
the seat Junior stool
Pressing 2 buttons and take off the
tray.
1. Take off 4 screws from
the bottom of the seat.
Remove the four (4) lower legs and
put on the four (4) anti-slip pads to
protect the upper legs before use.
High chair high chair without
tray
ASSEMBLY INSTRUCTIONS
mocka.co.nz I mocka.com.au
Macey 3-in-1 Highchair
ASSEMBLY INSTRUCTIONS
mocka.co.nz I mocka.com.au
Safety Harness Use
A
D
DD
C
B
Push buckles (A) and (B) into the buckle housing (C) until the buckle
prongs click into position.
Carefully adjust the harness by pulling the sliders (D) until the
desired fit is achieved in the lap, shoulders and crotch strap.
To remove your child from the harness:
Release the buckles (A) and (B) by squeezing the top and bottom
prongs either side of the buckle housing (C).
Remove the shoulder straps and lift the child out of the high chair.
A five-point safety harness is provided to restrain your child.
To secure your child in the harness:
/
