ATEN CS-88A User manual

Brand: ATEN

Model: CS-88A

Category: KVM switches

Type: User manual

This manual is also suitable for

CS88A
VS-88

Master View

KVM Switch

CS-88A

User Manual

www.aten.com

CS-88A User Manual

FCC Information

This is an FCC Class A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take

adequate measures.

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

RoHS

This product is RoHS compliant.

SJ/T 11364-2006

The following contains information that relates to China.

CS-88A User Manual

iii

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

International http://support.aten.com

North America ATEN TECH http://www.aten-usa.com/product_registration

ATEN NJ http://support.aten.com

International 886-2-8692-6959

North America ATEN TECH 1-888-999-ATEN

ATEN NJ 1-732-356-1703

CS-88A User Manual

Package Contents

The CS-88A package consists of:

 1 CS-88A KVM Switch

 1 Power Adapter

 1 Rack Mounting Kit

 1 User Manual*

 1 Quick Start Guide

Check to make sure that all the components are present and that nothing got

damaged in shipping. If you encounter a problem, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the unit, and/or any of the

devices connected to it.

* Features may have been added to the CS-88A since this manual was printed.

Please visit our website to download the most up-to-date version of the

manual.

Manual Part No. PAPE-0210-1AT

Manual Date: 2008

-08-20

All other brand names and trademarks are the registered property of their respective owners.

CS-88A User Manual

Contents

FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

SJ/T 11364-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

1. Introduction

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Consoles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Computers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2. Hardware Setup

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Stacking and Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Stacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Single Stage Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Two Stage Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Three Stage Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

3. Basic Operation

Hot Plugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Hot Plugging KVM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Hot Plugging Console Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Powering Off and Restarting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Manual Port Switching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Port ID Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

CS-88A User Manual

4. OSD Operation

OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

OSD Main Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

OSD Main Screen Headings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

OSD Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

F1: GOTO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

F2: LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

F3: SET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

F4: ADM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

F7: SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

F8: LOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

5. Hotkey Operation

Hotkey Port Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Invoking Hotkey Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Selecting the Active Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Auto Scanning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Invoking Auto Scan: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Skip Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Hotkey Beeper Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Hotkey Summary Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Appendix

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

North America. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

CS-88A Connection Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

OSD Factory Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Restoring Original Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . 44

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

CS-88A User Manual

vii

About this Manual

This User Manual is provided to help you get the most from your CS-88A

system. It covers all aspects of installation, configuration and operation. An

overview of the information found in the manual is provided below.

Chapter 1, Introduction, introduces you to the CS-88A system. Its

purpose, features and benefits are presented, and its front and rear panel

components are described.

Chapter 2, Hardware Setup, describes how to set up your installation. The

necessary steps – from a basic single stage hookup to a complete 3 stage

cascaded operation are provided.

Chapter 3, Basic Operation, explains the fundamental concepts involved

in operating the CS-88A.

Chapter 4, OSD Operation, provides a complete description of the

CS-88A's OSD (On Screen Display), and how to work with it.

Chapter 5, Hotkey Operation, details all of the concepts and procedures

involved in the Hotkey operation of your CS-88A installation.

An Appendix, provides specifications and other technical information

regarding the CS-88A.

CS-88A User Manual

viii

Conventions

This manual uses the following conventions:

Product Information

For information about all ATEN products and how they can help you connect

without limits, visit ATEN on the Web or contact an ATEN Authorized

Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means to

press the Enter key. If keys need to be chorded, they appear

together in the same bracket with a plus sign between them:

[Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential steps.

→ Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start

→ Run means to

open the Start menu, and then select Run.

Indicates critical information.

International http://www.aten.com

North America ATEN TECH http://www.aten-usa.com

ATEN NJ http://www.aten.com

Chapter 1

Introduction

Overview

The Master View CS-88A KVM Switch is a control unit that allows access to

multiple computers from a single console (keyboard, monitor, and mouse).

Before the development of the Master View, the only way to control multiple

computer configurations from a single console was through a complex and

costly network. Now, with the Master View CS-88A, you can easily access

multiple computers in a cost effective manner.

A single Master View CS-88A can control up to 8 computers. Since units can

be cascaded to three levels, in a full three stage installation up to 73 CS-88A

Master Views can control up to 512 computers – all from a single console.

Setup is fast and easy; plugging cables into their appropriate ports is all that is

entailed. There is no software to configure, so there is no need to get involved

in complex installation routines or be concerned with incompatibility

problems. Since the CS-88A intercepts keyboard input directly, it works on any

hardware platform and with all operating computers.

There are three convenient methods to access any computer connected to the

installation: (1) using the pushbutton port selection switches located on the

front panel; (2) entering Hotkey combinations from the keyboard; and (3)

selecting from menus provided by the On Screen Display (OSD). A powerful

Auto Scan feature also permits automatic scanning and monitoring of the

activities of all computers running on the installation one by one.

There is no better way to save time and money than with a Master View CS-

88A installation. By allowing a single console to manage all the attached

computers, a Master View CS-88A installation: (1) eliminates the expense of

having to purchase a separate keyboard, monitor, and mouse for each

computer; (2) saves all the space those extra components would take up; (3)

saves on energy costs; and (4) eliminates the inconvenience and wasted effort

involved in constantly moving from one computer to another.

CS-88A User Manual

Features

 Controls 8 computers from a single console

 Cascadable from any port to three levels for control of up to 512

computers from a single console

 Administrator/User password authorization for enhanced security

protection (PSP)

 Intelligent OSD (On Screen Display) and hotkey switching for efficient

system handling

 No software required – computer selection via front panel switches,

hotkeys, or On Screen Display (OSD)

 Auto Scan feature for monitoring user-selected computers

 Hot Pluggable, add or remove computers without powering off the switch

 PS/2 mouse emulation provided for system boot up

 Console PS/2 mouse controls all connected computers

 PS/2 compatible mouse support – Microsoft Intellimouse Explorer and

Logitech FirstMouse+ support*

 Superior video quality: up to 2048 x 1536; DDC; DDC2; DDC2B

 Rack mountable in 19" (1U) system rack

 Patented ASIC design for enhanced functionality and compatibility

* PS/2 compatible mouse support is for three button (wheel) mice. The

Logitech Mouse Ware program’s Change Device procedure does not work on

Microsoft NT systems.

Chapter 1. Introduction

Requirements

Consoles

The following hardware components are required for each KVM console:

 A VGA, SVGA, or MultiSync monitor capable of displaying the highest

resolution provided by any computer in the installation

 PS/2 Keyboard and mouse

Computers

The following hardware components are required for each computer:

 A VGA, SVGA, or MultiSync video graphics card with an HDB-15 port

 6-pin Mini-DIN PS/2 mouse and keyboard ports

Cables

Substandard cables may damage the connected devices or degrade overall

performance. For optimum signal integrity and to simplify the layout, we

strongly recommend that you use the high quality CS Custom Cable sets

described below:

Note: 1. The CS-88A does not support serial mice. You cannot use Serial-to-

PS/2 adapters with the cables. Attempts to do so will not work.

2. If your computer uses an AT style keyboard socket you will need to

purchase a PS/2-to-AT keyboard adapter (Part No. 2A-106, or any

standard keyboard adapter), in order to plug the cable into the

computer’s keyboard port.

Function Part Number - Length

Connecting Switch to Computer

Cascading Master Views

2L-1001P/C – 1.8 m

2L-1003P/C – 3 m

CS-88A User Manual

Components

Front View

No. Component Description

1 Port Selection

Switches

Press a switch to access the computer attached to the

corresponding port.

 Pressing Buttons 1 and 2 simultaneously for 3

seconds performs a Keyboard and Mouse Reset.

 Pressing 7 and 8 simultaneously starts Auto Scan

Mode (see page 29).

2 Port LEDs The Port LEDs are built into the Port Selection

Switches. The upper ones are the On Line LEDs; the

lower ones are the Selected Port LEDs:

 The On Line LEDs light ORANGE to indicate that the

computer attached to the corresponding port is up

and running. If the LED is flashing, it indicates that

the Port is being used for cascading to another

Master View switch (see Two Stage Installation,

page 10).

 The Selected LEDs light GREEN to indicate that the

computer attached to the corresponding port is the

one that has the KVM focus. The LED is steady

under normal conditions, but flashes when its port is

accessed under Auto Scan Mode (see F7: SCAN,

page 29).

3 Reset Button Use a small object (such as the end of a paper clip, or a

ballpoint pen) to press this recessed switch to initiate a

warm reset. If the switch is kept in for longer than three

seconds, a cold reset takes place.

4 Power LED Lights (blue) to indicate that the unit is receiving power.

1&2 34

Chapter 1. Introduction

Rear View

No. Component Description

1 Power Jack The unit is designed to be non-powered (external

power is not required - its operating power comes from

the computers). In general, the only time that external

power is necessary is when operation becomes erratic

because the unit isn’t obtaining enough power from

the computer connections. If you choose to use

external power, the power adapter cable plugs in here.

2Console Ports

 If this is a first station unit, your monitor, keyboard

and mouse plug in here.

 If this is a cascaded unit, the cables that link back to

a port on a higher Master View unit plug in here.

3 KVM Ports The cables that link to the computers plug in here.

CS-88A User Manual

This Page Intentionally Left Blank

Chapter 2

Hardware Setup

Before You Begin

Stacking and Rack Mounting

The CS-88A can be stacked on a desktop or rack mounted in 1U of rack space.

The procedures for each method are described in the following sections.

Stacking

CS-88A devices can be stacked one on top of the other using the stacking

brackets that come already attached to the unit.

Note that there is a top and bottom half to each bracket. The top half has a

convex surface; the bottom half has a concave surface. Line up the four bottom

brackets of the top unit with the four top brackets of the bottom unit; then fit

the top unit down onto the bottom unit.

1. Important safety information regarding the placement of this

device is provided on page 37. Please review it before proceeding.

2. Make sure that the power to any device that you connect to the

installation has been turned off. You must unplug the power cords

of any computers that have the Keyboard Power On function.

CS-88A User Manual

Rack Mounting

1. First remove the stacking brackets by unscrewing them from the unit, as

shown in the diagram below:

2. Next screw the mounting brackets into the sides of the unit, as shown in

the diagram below:

3. Slide the unit into the rack and secure it to the rack.

Chapter 2. Hardware Setup

Single Stage Installation

In a single stage installation, there are no additional switches cascaded down

from the first unit. To set up a single stage installation do the following:

1. Plug your keyboard, mouse, and monitor into the unit's Console Ports.

2. Use KVM cable sets (as described in the Cables section on page 3), to

connect any available KVM Port to the Keyboard, Video and Mouse ports

of the computer you are installing.

3. If you choose to use external power, plug the power adapter cable into the

Master View’s Power Jack, then plug the adapter into an AC power source.

Note: Under non-powered operation, the unit gets its power from the

computers via the cables. If a computer, only supplies 3.3V of power

for the keyboard and mouse instead of 5V (as in the case of

Notebooks, for example), the unit will not receive enough power,

and you will need to use the external power adapter.

4. Turn on the power to the computers.

Note: If you choose to use external power, the Master View unit must be

plugged in and receiving power prior to turning on the power to the

computers.

Single Stage Installation Diagram

CS-88A User Manual

Two Stage Installation

To control even more computers, up to eight additional Master View CS-88A

units can be cascaded from the KVM ports of the First Stage unit. The cascaded

Master Views that connect back to the First Stage unit are considered Second

Stage units. As many as 64 computers can be controlled in a complete two

stage installation. A table showing the relation between the number of

computers and the number of Master View units needed to control them is

provided on page 42.

Note: 1. Mixing different Master View models on the same installation can

cause problems with OSD port switching. We strongly recommend

that all cascaded units be the same model as the First Stage unit.

2. If you are adding this switch into an already existing CS-88A

configuration, be sure to make it the First Stage unit. Otherwise, you

won’t get the benefit of its improved OSD features and functions.

To set up a two stage installation do the following:

1. Make sure that power to all the devices you will be connecting up,

including all preexisting devices on the installation, have been turned off.

2. Use a KVM cable set (described in the Cables section, page 3), to connect

any available KVM Port on the First Stage unit to the Console Port

connectors of the Second Stage unit.

3. Use KVM cable sets (described in the Cables section, page 3), to connect

any available KVM port on the Second Stage unit to the Keyboard, Video,

and Mouse ports of the computer you are installing.

4. Plug the power adapter cable into the Master View’s Power Jack, then plug

the adapter into an AC power source.

5. Repeat these steps for any other Second Stage units you wish to connect.

6. Plug in the power adapter for the First Stage Master View unit.

7. Turn on the power to all the computers.

Note: The Power On sequence requires that all Second Stage units be

powered on first. After all the Second Stage units have been

powered on, the First Stage unit must be powered on next. After the

Second and First stage units have been powered on, the computers

can be powered on.

Chapter 2. Hardware Setup

Two Stage Installation Diagram

CS-88A User Manual

Three Stage Installation

The procedures for setting up a three stage installation are essentially the same

as for a two stage installation. With a three stage setup, as many as 512

computers can be controlled in a complete installation. A table showing the

relation between the number of computers and the number of Master View

units needed to control them is provided on page 42.

Note: 1. See Notes 1 and 2 at the beginning of the Two Stage Installation

section.

2. Master View units cannot be cascaded beyond the third level.

To set up a three stage installation do the following:

1. Make sure that power to all the devices you will be connecting up,

including all preexisting devices on the installation, have been turned off.

2. Use a KVM cable set (described in the Cables section, page 3), to connect

any available KVM Port on the Second Stage unit to the Console Port

connectors of the Third Stage unit.

3. Use KVM cable sets (described in the Cables section, page 3), to connect

any available KVM port on the Third Stage unit to the Keyboard, Video,

and Mouse ports of the computer you are installing.

4. Plug the power adapter cable into the Master View’s Power Jack, then plug

the adapter into an AC power source.

5. Repeat these steps for any other Third Stage units you wish to connect.

6. Plug in the power adapters for all the Second Stage Master View units.

7. Plug in the power adapter for the First Stage Master View unit.

8. Turn on the power to all the computers.

Note: The Power On sequence requires that all Third Stage units be

powered on first. After they are all on, the Second Stage units must

be powered on next. After all the Second Stage units are on, the First

Stage unit must be powered on. Only after all the Master Views have

been powered on in this sequence, can the computers be powered

on.

Page is loading ...

ATEN CS-88A User manual

Brand: ATEN

Model: CS-88A

Category: KVM switches

Type: User manual

This manual is also suitable for

CS88A
VS-88

Download PDF

report

ATEN CS-88A User manual

This manual is also suitable for

ATEN CS-88A User manual

Related papers

Other documents