FCC STATEMENT
The KVM Switch has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
according to the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which is found by turning
the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
w Reorient or relocate the receiving antenna
w Increase the separation between the
equipment or device
w Connect the equipment to an outlet other
than the receiver’s
w Consult a dealer or an experienced
radio/TV technician for assistance
I. Installation and Power-up
1. First Time Set-up: Please turn off all
computers and plug the user
console-keyboard, video monitor, and
mouse-into corresponding user port and then
plug the adapter into the switch.
2. Unwrap KVM cable, plug HDB-15 end to a
selected switch channel and the other end of
the cable to a PC’s keyboard/mouse/video
ports. Then power on the PC.
3. For PC’s Hot Plug-and-Play, please connect
mouse connecter first, then connect
keyboard and video connecter.
4. During installation or operation, if you face
any signal problem, you can press down
both the front-panel number <1> and <2> to
reset the system. The keyboard LEDs will
blink to confirm the action of reset.
II. KVM Switch Operation
1. Front Panel Push Buttons
(1) You may select a computer by pressing
the front panel push button. If the channel
connected to a power-on computer, the
front panel LED will show orange. If
shows with blue LED, it reflects the
selected computer.
(2) Auto Scan: By pressing the push button
<3> and <4>, you can activate Auto Scan
function to scan power-on computers.
Please note that the function is only
available on SP214A.
(3) Reset: By pressing the front-panel
number <1> and <2> to reset the system,
the keyboard LEDs will blink to confirm
the action of reset.
2. Hot-key Commands
(1) You may start with two <Scroll Lock>
keystrokes followed by number keystroke
<1> to <2> or <1> to <4> switch over 2/4
computers. After you activate hot-key
function, the keyboard LEDs will blink
and then followed by typing the channel
number to switch.
(2) Auto Scan: Press <Scroll Lock>+<Scroll
Lock>+<F4> to automatically scan
power-on computers. You may change
scan rate by press following keystrokes:
-
1
-
-
2
-
-
3
-
Setting F1 F2 F3
Interval (sec.)
5 10 20
You may press two <Scroll Lock>+<Esc>
to stop Auto Scan
(3) Manual Scan: Press <Scroll
Lock>+<Scroll Lock>+<Space> to switch
to the next power-on computer.
(4) During operation, if you face any signal
problem, you can press down both the
front-panel number <1> and <2> to reset
the system, the keyboard LEDs will blink
to confirm the action of reset.
III. Remarks
1. Before operating this KVM switch, please
read this manual carefully.
2. Please plug KVM switch adapter and use
high quality 3-in-1 KVM cable for optimum
operation.
3. To prevent potential power damage:
(1) Please don’t use 2-wire extension cable.
(2) Please ensure AC outlets at PCs and
monitors are on the same phase and
have correct grounding.
IV. Limited Warranty:
1. In no events shall the direct vendor’s liability
for direct or indirect, special, incidental or
consequential damages, loss of profit, loss of
business, or financial loss which hay be
caused by the use of the product exceeds
the price paid for the product.
2. The direct vendor makes no warranty or
representation, expressed or implied with
respect to the contents or use of this
documentation, and especially disclaims its
quality, performance, merchantability, or
fitness for any particular purpose.
3. The direct vendor also reserves the right to
revise or update the product or
documentation without obligation to notify
any user of such revisions or updates. For
further information, please contact your
direct vendor.
P/N: 2300-0169
Installation Guide
KVM Switch
Model No.: SP212A, SP214A
http://www.micronet.info
-
4
-
-
5
-
/
