EK Water Blocks 3831109840016 User manual

EK Water Blocks
Brand
EK Water Blocks
Model
3831109840016
Category
Computer liquid cooling
Type
User manual

This manual is also suitable for

EK Water Blocks 3831109840016 is a reservoir and pump combo that is designed to be used in a custom liquid cooling loop. The reservoir has a capacity of 150ml and is made of acrylic. The pump is a Laing DDC 3.2 pump that is capable of pumping up to 500l/h. The combo also includes a mounting bracket that allows it to be mounted to a 120mm fan mount.

This combo is a good option for users who are looking for a compact and powerful reservoir and pump combo. It is also a good option for users who are new to custom liquid cooling, as it is easy to install and use.

Here are some of the features of the EK Water Blocks 3831109840016:

EK Water Blocks 3831109840016 is a reservoir and pump combo that is designed to be used in a custom liquid cooling loop. The reservoir has a capacity of 150ml and is made of acrylic. The pump is a Laing DDC 3.2 pump that is capable of pumping up to 500l/h. The combo also includes a mounting bracket that allows it to be mounted to a 120mm fan mount.

This combo is a good option for users who are looking for a compact and powerful reservoir and pump combo. It is also a good option for users who are new to custom liquid cooling, as it is easy to install and use.

Here are some of the features of the EK Water Blocks 3831109840016:

Installation and mounting manual for EK-Reservoir Combo DCP 2.2/4.0
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EKWB d.o.o. assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com
for updates.
The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the
liquid seal is made using o-rings.
EKWB recommends 24 hour leak testing for all EK products before powering on the computer. This will eliminate any damages that may occur because of the users improper installation or
products imperfections.
STEP 1: GENERAL INFORMATION. Sample picture of EK-Reservoir Combo DCP 4.0 mounted on EK-DCP 4.0 pump.
STEP 2: PREPARING YOUR PUMP. STEP 3: PREPARING YOUR RESERVOIR.
1. REMOVING SCREWS. Take your pump (picture represents EK-DCP 4.0) out
of package and unscrew screws that are holding cover on pump housing. DO
NOT open pump as there is no need for doing that.
2. Insert 4 enclosed screws M3x20 ISO7380 into holes. After that insert
gasket into the channel as shown on picture bellow.
STEP 4: CONNECTING RESERVOIR WITH PUMP.
Put together reservoir and pump and make sure all 4 screws fall into threaded holes on pump. Afterwards screw them in with enclosed allen key. Final
product should look like on picture above (step 1).
STEP 4: OTHER INSTRUCTIONS
Please note that EKWB holds no responsibility of any kind if assembly is not made by instructions. This applies also for all products that are
not listed as compatible on web page (http://www.ekwaterblocks.com/shop/ek-reservoir-combo-dcp-4-0.html). Users must by all means
also consider instructions that are being made for proper use of pump.
CAUTION! Please do not use high
force when tightening the mounting
screws. Applying too much force
may damage the mounting screw or
threads in the pump and may render
the pump useless.
Rel easedon4
th
ofNovember,2009.
Installation and mounting manual for EK-Reservoir Combo DCP 2.2/4.0
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EKWB d.o.o. assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com
for updates.
The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the
liquid seal is made using o-rings.
EKWB recommends 24 hour leak testing for all EK products before powering on the computer. This will eliminate any damages that may occur because of the users improper installation or
products imperfections.
STEP 1: GENERAL INFORMATION. Sample picture of EK-Reservoir Combo DCP 4.0 mounted on EK-DCP 4.0 pump.
STEP 2: PREPARING YOUR PUMP. STEP 3: PREPARING YOUR RESERVOIR.
1. REMOVING SCREWS. Take your pump (picture represents EK-DCP 4.0) out
of package and unscrew screws that are holding cover on pump housing. DO
NOT open pump as there is no need for doing that.
2. Insert 4 enclosed screws M3x20 ISO7380 into holes. After that insert
gasket into the channel as shown on picture bellow.
STEP 4: CONNECTING RESERVOIR WITH PUMP.
Put together reservoir and pump and make sure all 4 screws fall into threaded holes on pump. Afterwards screw them in with enclosed allen key. Final
product should look like on picture above (step 1).
STEP 4: OTHER INSTRUCTIONS
Please note that EKWB holds no responsibility of any kind if assembly is not made by instructions. This applies also for all products that are
not listed as compatible on web page (http://www.ekwaterblocks.com/shop/ek-reservoir-combo-dcp-4-0.html). Users must by all means
also consider instructions that are being made for proper use of pump.
CAUTION! Please do not use high
force when tightening the mounting
screws. Applying too much force
may damage the mounting screw or
threads in the pump and may render
the pump useless.
Rel easedon4
th
ofNovember,2009.
  • Page 1 1
  • Page 2 2

EK Water Blocks 3831109840016 User manual

EK Water Blocks
Brand
EK Water Blocks
Model
3831109840016
Category
Computer liquid cooling
Type
User manual
This manual is also suitable for

EK Water Blocks 3831109840016 is a reservoir and pump combo that is designed to be used in a custom liquid cooling loop. The reservoir has a capacity of 150ml and is made of acrylic. The pump is a Laing DDC 3.2 pump that is capable of pumping up to 500l/h. The combo also includes a mounting bracket that allows it to be mounted to a 120mm fan mount.

This combo is a good option for users who are looking for a compact and powerful reservoir and pump combo. It is also a good option for users who are new to custom liquid cooling, as it is easy to install and use.

Here are some of the features of the EK Water Blocks 3831109840016:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents