EK Water Blocks 3831109855294 User manual
- Category
- Computer liquid cooling
- Type
- User manual
This manual is also suitable for
EK Water Blocks 3831109855294 is a water cooling component that allows for the connection of multiple water blocks in either serial or parallel configurations.
- Serial configuration: Water flows through the blocks in sequence, resulting in lower overall flow rate but higher pressure drop.
- Parallel configuration: Water flows through all blocks simultaneously, resulting in higher overall flow rate but lower pressure drop.
The device includes:
- EK-FC Bridge: Connects water blocks together.
- EK-FC Link: Attaches water blocks to the bridge.
The device is compatible with EK Full Cover water blocks and requires the use of o-rings for sealing. It is important to avoid overtightening the screws when assembling the device to prevent damage.
EK Water Blocks 3831109855294 is a water cooling component that allows for the connection of multiple water blocks in either serial or parallel configurations.
- Serial configuration: Water flows through the blocks in sequence, resulting in lower overall flow rate but higher pressure drop.
- Parallel configuration: Water flows through all blocks simultaneously, resulting in higher overall flow rate but lower pressure drop.
The device includes:
- EK-FC Bridge: Connects water blocks together.
- EK-FC Link: Attaches water blocks to the bridge.
The device is compatible with EK Full Cover water blocks and requires the use of o-rings for sealing. It is important to avoid overtightening the screws when assembling the device to prevent damage.
Revison 1.1. Released on March 5
th
2012
Installation and mounting manual for
EK-FC Bridge and EK-FC Link
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EKWB d.o.o. assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.
The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. T
hese fittings do not need to be tightened with much force
because the liquid seal is made using o-rings. EKWB recommends 24 hour leak testing for all EK products before powering on the computer. This will eliminate any damages that may occur
because of the users improper installation or products imperfections.
VERY IMPORTANT NOTICE:
When tightening the screw into the acetal make sure not to overtighten it.
Overtightening the screw will damage the thread, rendering the product useless.
STEP 1: GENERAL INFORMATION.
STEP 2: GENERAL INFORMATION: SERIAL vs PARALLEL
Example picture of installed triple EK-FC Bridge and EK-FC Links
Serial or successive flow:
Water starts flowing initially through first
block, continues to second block and ends up
with the third block.
Overall system water flow is lower (pressure
drop is higher) compared to parallel flow due
to higher restriction.
Parallel flow:
Water flows through all blocks simultaneously.
With such configuration each water block gets
one third of all flow. Overall system water
flow is higher (pressure drop is lower)
compared to serial or successive flow.
STEP 3: CCHOOSING INLET AND OUTLET PORT
Only one port must be used as an inlet and only one port as an outlet!
Ports can be exchanged, meaning inlet can be used as outlet and at the same time outlet can be used as inlet.
STEP 4: ATTACHING THE LINK PART TO WATER BLOCK
Unscrew three encircled M4×8mm screws
with enclosed 2,5mm Allen key.
Prepare the link and use two 15x1,5mm
o-rings on the G1/4 threads of the top.
Use two M4×20 screws and one M4×25 screw
to attach FC Link to Full Cover water block. Do
not use high force when tightening.
FC BRIDGE part
FC LINK parts
FC Water Block
BRIDGE Triple Parallel
BRIDGE Triple Serial
BRIDGE Dual Parallel
BRIDGE Dual Serial
Revison 1.1. Released on March 5
th
2012
VERY IMPORTANT NOTICE:
When tightening the screw into the acetal make sure not to overtighten it.
Overtightening the screw will damage the thread, rendering the product useless.
STEP 5: ATTACHING THE BRIDGE PART TO CONNECT WATER BLOCKS
Plug both G1/4 ports on copper with encircled
EK-Plug G1/4. Use Allen key to tighten the plug.
Use enclosed 2,5mm Allen key to screw in all M4 screws. Do not use high force to tighten them.
Over tightening the screws will damage the threads, rendering the product useless.
BRIDGE and LINK OPTIONS and ACCESSORIES
EK-FC Bridge TRIPLE
Serial
EK-FC Bridge TRIPLE
Parallel
EK-FC Bridge DUAL Serial
EK-FC Bridge DUAL
Parallel
EK-FC Link R48X0/58X0
EK-FC Link R5970
EK-FC Link GeForce
EK-FC Link BLANK
for Triple Serial Bridge
OTHER INSTRUCTIONS
Please note that EKWB holds no responsibility of any kind if assembly is not made by instructions. This applies also for all products
that are not listed as compatible on web page. Users must by all means also consider instructions that are being made for proper
use of pump and other water cooling components provided by manufacturer(s).
HINT: Never let your pump dry running. If that happens for prolonged period of time you risk destroying bearing and rendering
pump useless.
1 × Screw
M4×20mm
5 × Screws M4×16mm.
(For Dual ver. 3 screws)
Install 6 × O-rings into the Link channel
provided with EK-FC Link delivery.
(For Dual version only 4 o-rings)
G1/4 plug
-
1
-
2
EK Water Blocks 3831109855294 User manual
- Category
- Computer liquid cooling
- Type
- User manual
- This manual is also suitable for
EK Water Blocks 3831109855294 is a water cooling component that allows for the connection of multiple water blocks in either serial or parallel configurations.
- Serial configuration: Water flows through the blocks in sequence, resulting in lower overall flow rate but higher pressure drop.
- Parallel configuration: Water flows through all blocks simultaneously, resulting in higher overall flow rate but lower pressure drop.
The device includes:
- EK-FC Bridge: Connects water blocks together.
- EK-FC Link: Attaches water blocks to the bridge.
The device is compatible with EK Full Cover water blocks and requires the use of o-rings for sealing. It is important to avoid overtightening the screws when assembling the device to prevent damage.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
EK Water Blocks 3831109855157 User manual
-
-
-
-
-
-
-
-
EK Water Blocks 3831109868966 User manual
-
