Chief K1C200B Installation guide

K1C200B
Chief
Brand
Chief
Model
K1C200B
Category
Flat panel desk mounts
Type
Installation guide

This manual is also suitable for

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
K1C100
K1C200
K1D100
K1W100
K1D200
K1W200
K1P100
K1P200
Height-adjustable Monitor Arm Series
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
K1 Series
K1 Series Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm).
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the K1 Series Monitor Arm
up to (and including) the display does not exceed 25 lbs
(11.34 kg) per arm. Use with products heavier than the
maximum weight indicated may result in collapse of the
mount and its accessories causing possible injury.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS!--
Installation Instructions K1 Series
3
DIMENSIONS
14.70
±6.5
3.94
100
2.95
75
CABLE
MANAGEMENT
COVER
CABLE
MANAGEMENT
COVER QUICK RELEASE
VESA INTERFACE
90 INTERFACE
ROTATION
MAX 19.9 [505.5]
EXTENSION
MIN 2.09 [53.14]
.75
MAX 2.50 [63.5]
19.05
DESKTOP THICKNESS RANGE
4.66
118.3
PITCH TENSION
ADJUSTMENT
PITCH RANGE
10
DOWN
75
UP
K1D100
3.937
2.953
21.155
8.053
QUICK RELEASE
VESA INTERFACE
CABLE
MANAGEMENT
COVER
CABLE
HEIGHT
ADJUSTMENT
90 INTERFACE
ROTATION
16.19
411.2
MAX 19.9 [505]
EXTENSION
MIN 2.09 [53.2]
.75 MIN
2.50 MAX [63.5]
19.1
DESKTOP THICKNESS RANGE
4. 65
118.2
PITCH RANGE
10 DOWN
75
UP
MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 34.92
" [887]
K1D200
K1 Series Installation Instructions
4
DIMENSIONS (CONTINUED)
K1W100
15.71
±6.5
399±165.1
HEIGHT
ADJUSTMENT
2.95
75
3.94
100
CABLE
COVER
CABLE
MANAGEMENT
COVER
QUICK RELEASE
VESA INTERFACE
90 INTERFACE
ROTATION
7.41
188.1
MAX 19.9 [505]
EXTENSION
MIN 2.09 [53.2]
PITCH TENSION
ADJUSTMENT
PITCH RANGE
10
DOWN
75
UP
3.22
81.7
2.43
61.6
5.51
140
11.22
284.9
15.71
399
3.937
2.953
QUICK RELEASE
VESA INTERFACE
CABLE
MANAGEMENT
COVER
CABLE
HEIGHT
ADJUSTMENT
90 INTERFACE
ROTATION
16.19
411.2
MAX 19.9 [505]
EXTENSION
MIN 2.09 [53.2]
PITCH RANGE
10
DOWN
75 UP
2.53
64.3
5.61
142.6
3.22
81.7
4.67
118.6
17. 60
MAX
HEIGHT
446.9
4.49
MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 34.92
" [887]
K1W200
Installation Instructions K1 Series
5
DIMENSIONS (CONTINUED)
K1C100
3.94
100
2.95
75
32.86 [834.6]
TOTAL HEIGHT ADJUSTMENT
13" LIFT ARM HEIGHT
ADJUSTMENT
CABLE
MANAGEMENT
COVER
CABLE
MANAGEMENT
COVER
QUICK RELEASE
VESA INTERFACE
90 INTERFACE
ROTATION
7.41
PITCH TENSION
ADJUSTMENT
PITCH RANGE
10
DOWN
75
UP
HEIGHT
ADJUSTMENT
KNOB
LOWER PROFILE INSTALL
LOWER
PROFILE
3.937
2.953
32.86 [834.6]
TOTAL HEIGHT
ADJ USTME NT
9.11 [231.4]
MAX HEIGHT
10.75
273.1
QUICK RELEASE
VESA INTERFACE
CABLE
MANAGEMENT
COVER
CABLE
HEIGHT
ADJUSTMENT
90 INTERFACE
ROTATION
17.69
449.3
.50
MAX 3.25 [82.6]
12.7
DESKTOP THICKNESS RANGE
MAX 19.5 [495.3]
EXTENSION
MIN 2.13 [54.0]
1.50
38.1
PITCH RANGE
10
DOWN
75 UP
HEIGHT
ADJUSTMENT
KNOB
MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 36.5" [927.1]
K1C200
K1 Series Installation Instructions
6
DIMENSIONS (CONTINUED)
K1P100
2.95
75
3.94
100
13.60±6.50
HEIGHT ADJUSTMENT
2.50
CABLE
MANGEMENT
COVER
CABLE
MANGEMENT
COVER
QUICK RELEASE
VESA INTERFACE
90 INTERFACE
ROTATION
7.41
188.1
2.297
(MAX 19.12)
POLE CLAMP RANGE
1.50" - 1.90" [38.1 - 50.8]
PITCH TENSION
ADJUSTMENT
PITCH RANGE
10
DOWN
75 UP
3.937
2.953
QUICK RELEASE
VESA INTERFACE
CABLE
MANAGEMENT
COVER
CABLE
HEIGHT
ADJUSTMENT
90 INTERFACE
ROTATION
16.19
411.2
2.172
(MAX 19.00")
POLE CLAMP RANGE
1.50 [38.1] - 1.90 [48.26]
MAX
519.4
20.45
PITCH RANGE
10 DOWN
75
UP
MAXIMUM WIDTH OF 2 PARALLEL, FORWARD-FACING DISPLAYS: 34.92
" [887]
K1P200
Installation Instructions K1 Series
7
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
K1 Series Installation Instructions
8
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
3/16" (included)
1/8" (included)
5/32" (included with K1P Series only)
A (1)
[monitor arm]
(K1D100 shown)
B (4 or 8)*
M4x14mm
C (4 or 8)*
M4x25mm
D (4 or 8)*
M10x5.3x10
included with K1W Series (wall mount) only!
E (1)
[wall bracket]
F (2)
1/4 x 2 1/2"
G (2)
1/4"
3/16"
1/8"
M (1)
N (1)
*8 screws and spacers
included with dual arm mounts
included with K1P Series (pole mount) only!
H (1)
[pole clamp]
5/32"
J (4)
1/4-20 x 1 1/2"
K (4)
1/4-20 x 1"
L (1)
Installation Instructions K1 Series
9
Assembly And Installation
Connecting K1C Series (column mount) to Desk
Standard Installation
1. Loosen clamp screw until enough space is created between
clamp and mount to allow for desk mounting.(See Figure 1)
NOTE: If space is limited behind desk (i.e. against wall, etc.),
remove clamp screw and attachment entirely and
reattach clamp screw prior to Step 3! (See Figure 2)
2. Place mount on top of desk at desired mounting location.
(See Figure 1)
3. Tighten clamp using clamp screw until mount is securely
fastened to desk. (See Figure 1)
Figure 1
Figure 2
Low Profile Installation (K1C Series Only)
1. Remove top cap from column. (See Figure 3)
2. Slide mount assembly off of column. (See Figure 3)
Figure 3
3. Rotate mount in 90 degrees in either direction prior to
reinstalling onto column. (See Figure 4)
4. Reinstall onto column and adjust to desired height. (See
Figure 4)
5. Reinstall top cap to column. (See Figure 4)
Figure 4
6. Proceed with standard installation to desk as shown in
"Standard Installation" section.
1
2
3
desk
1
2
3
4
5
K1 Series Installation Instructions
10
Connecting K1D Series (desk mount) to Desk
1. Loosen clamp screw until enough space is created between
clamp and mount to allow for desk mounting. (See Figure 5)
NOTE: If space is limited behind desk (i.e. against wall, etc.),
remove clamp entirely in Step 1 and reattach clamp
prior to Step 3!
2. Place mount on top of desk at desired mounting location.
(See Figure 5)
3. Tighten clamp using clamp screw until mount is securely
fastened to desk. (See Figure 5)
Figure 5
Connecting K1W Series (wall mount) to Wall
1. Determine mounting location on wall.
2. Use a stud finder to locate 2" x 4" wood stud.
3. Use wall bracket to mark and drill two 3/16 x 2 1/2" holes in
wall at desired mounting location. (See Figure 6)
4. Use two 1/4-2 1/2" hex head lag screws (F) and two 1/4"
washers (G) to install wall bracket onto wall. (See Figure 6)
IMPORTANT ! : Overtightening screws (F) may cause
bracket to compress into soft wall surface resulting in
difficult mount installation or improper engaging of set
screw in Step 6.
5. Hang monitor arm (A) over wall bracket. (See Figure 6)
6. Secure monitor arm to wall bracket by tightening set screw.
Ensure set screw engages back side of wall bracket (E) to
properly secure mount. (See Figure 6)
1
1
2
3
desk
Figure 6
(F) x 2
(E)
(G) x 2
3
4
5
set screw
6
side view
Installation Instructions K1 Series
11
Connecting K1P Series to Pole
1. Determine approximate location for mount keeping in mind
display size, extension, height adjustment requirements.
2. Place mount (A) against pole with clamp (H) on opposite
side of pole. (See Figure 7)
Figure 7
3. Using 5/32" hex key (L) and appropriate length screws,
loosely attach K1P assembly to pole clamp (H). If installing
to 1 1/2" NPT pipe, use 1/4-20 x 1 1/2" button head cap
screws (J). If installing to 1 1/2" diameter pipe, use 1/4-20 x
1" button head cap screws (K). (See Figure 7)
4. Position mount at desired height and orientation.
5. Equally tighten screws against mount and the pole clamp.
Display Installation
1. Remove quick release faceplate from mount by pressing
quick release tab and sliding faceplate off mount. (See
Figure 8)
Figure 8
WARNING: Only remove display from mount when the
display can be lifted up from the mount! DO NOT remove
display unless the display is in the upright position! See
Display Removal section for details.
2. Carefully place display face down on protective surface.
3. Connect faceplate to display
For flush mounting hole installation:
• Using Phillips screwdriver, carefully install four
M4x14mm screws (B) through corresponding
holes on faceplate and into the mounting holes on
the display. (See Figure 9)
Figure 9
For recessed mounting hole installation:
• Place four spacers (D) on top of mounting holes
on back of display. (See Figure 10)
• Using Phillips screwdriver, carefully install four
M4x25mm screws (C) through corresponding
holes on faceplate, spacers (D) and into the
mounting mounting holes on the display. (See
Figure 10)
3
(J or K) x 4
(H)
K1P assembly
quick release tab
1
1
(B) x 4
quick release
faceplate
(for flush mounting holes)
3
K1 Series Installation Instructions
12
Figure 10
4. Position display with faceplate attached above mount. (See
Figure 11)
5. Slide faceplate onto mounting head until quick release tab
clicks into place. (See Figure 11)
Figure 11
Adjustments
Head Tilt Adjustment
1. Adjust head tilt to desired tilt position. (See Figure 12)
2. Adjust head tilt tension screw to change the adjustment
tension. (See Figure 12)
Height Adjustment
1. Adjust height to desired level. (See Figure 12)
2. Open cable management cover on upper arm to expose
height-adjustable tension screw. See Cable Management
section for details.
3. Use 1/8" hex key (J) to adjust height-adjustable tension
screw to change adjustment tension. (See Figure 12)
NOTE: Turn clockwise to reduce tension for lighter displays
and counter-clockwise to increase tension for heavier
displays.
4. Close cable management cover on upper arm. See Cable
Management section for details.
Pivot Adjustment
1. Adjust pivot position as desired. (See Figure 12)
2. Use 3/16" hex key (H) to adjust pivot point tension screws
to change pivot adjustment tension. (See Figure 12)
Figure 12
(for recessed mounting holes)
(C) x 4
(D) x 4
quick release
faceplate
3
5
height-adjustable tension
head tilt tension
pivot point
tension
Installation Instructions K1 Series
13
Pivot Adjustment Range
Single Arm Models (K1D100, K1C100, K1W100 and
K1P100)
1. Adjust arm angle as desired up to 90 degrees in either
direction. (See Figure 13)
WARNING: Swinging the arm beyond 90 degrees may
result in the mount slipping off the desk causing serious
injury!
Figure 13
Dual Arm Models (K1D200, K1C200, K1W200 AND
K1P200)
1. Adjust arm angles as desired within a 90 degree range from
the edge of desk or wall and a perpendicular centerline of
mount. (See Figure 14)
WARNING: Swinging the arm beyond this range may result
in the mount slipping of the desk causing serious injury!
Figure 14
Column Height Adjustment (K1C Series only)
1. Loosen column adjustment knob. (See Figure 15)
2. Adjust height to desired level. (See Figure 15)
3. Tighten column adjustment knob. (See Figure 15)
Figure 15
(top view)
+/- 90 degrees range
of motion
edge of desk or wall face
perpendicular centerline
90 degrees range
of motion per arm
edge of desk or wall face
(top view)
2
1
3
K1 Series Installation Instructions
14
Portrait Adjustment
1. The monitor may be adjusted 90 degrees in either direction
in order to provide a portrait view of the monitor. (See Figure
16)
Figure 16
WARNING: Only remove display from mount when the
display can be lifted up from the mount! DO NOT remove
display unless the display is in the upright position! See
Display Removal section for details.
Cable Management
1. Use screwdriver to unhinge tab on either end of cable
management cover on upper arm. (See Figure 17)
2. Slide screwdriver along edge of cover until remaining tabs
are unhinged and cover is in the "open" position. (See
Figure 17)
Figure 17
Figure 18
3. Route cables through cable management channels. (See
Figure 18)
IMPORTANT ! : Be sure to leave enough slack in the
cables near display and arm joint to allow for full arm
articulation!
4. Close cable management covers on monitor arm. (See
Figure 18)
5. Repeat Steps 1-4 for lower arm.
cable management cover
1
2
2
2
4
4
3
3
cable (typical)
Installation Instructions K1 Series
15
Display Removal
WARNING: Only remove display from mount when the
display can be lifted up from the mount! DO NOT remove
display unless the display is in the upright position! (See
Figure 19)
1. Make sure display is in the upright position.
2. Remove quick release faceplate from mount by pressing
quick release tab and sliding faceplate off mount. (See
Figure 19)
Figure 19
quick release tab
2
K1 Series Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
F 877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
F +31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002059 Rev 03
2011 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
12/11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Chief K1C200B Installation guide

K1C200B
Chief
Brand
Chief
Model
K1C200B
Category
Flat panel desk mounts
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents