Rocstor Rocport ID 5 320 GB User manual

1

store your future

ROCPORT ID5

User Manual

Page | 2

ROCSTOR

|

ROCPORT ID5

user manual

TABLE OF CONTENTS

IMPORTANT NOTICES 4

• Safety Notices ________________________________________________________ 4

• General Notices

• Capacity Disclaimer ____________________________________________________ 4

• Care and Handling 4

GENERAL 6

• Introduction ___ _____________________ ___________________________ 6

• Box Contents 6

• Minimum System Requirements ____________________ _________________ 7

• Connectors and Rocport ID5 rear view 7

QUICK INSTALLATION 8

• How to Connect the Interface Cables - Connecting the Drive ___________________ 8

• Cable Types: FireWire 400, USB 9

INSTALLING YOUR DRIVE 10

• Rocport ID5 as a bootable device _________________________________________ 10

• Disconnecting Your Drive 10

o PC _______________________________________________________________ 10

o Mac 11

• Reformatting Your Drive ________________________________________________ 11

o Reformatting via PC (Window based computers) 11

o Reformatting via Mac _______________________________________________ 11

• Important Note 11

• How to Daisy-Chain through FireWire ports to your Rocport ID5 Drive at one time __ 12

PARTITIONING AND FORMATTING THE ROCPORT ID5 DRIVE ON A MAC OS 13

• Warning _____________________________________________________________ 13

• Important Notes 13

• Instructions for Partitioning and Formatting from FAT 32 to HFS+ _______________ 14

PARTITIONING & FORMATTING the ROCPORT Drive on WINDOWS 2000, XP and VISTA 20

• Warning _____________________________________________________________ 20

• Important Notes 20

• Different ways to get to the Control Panel __________________________________ 21

• Instructions upon reaching the Control Panel 23

• Instructions for Partitioning and Formatting from FAT 32 to NTFS _______________ 24

Page | 3

ROCSTOR

|

ROCPORT ID5

user manual

TROUBLESHOOTING 31

• Troubleshooting for Macintosh computers _________________________________ 31

• Troubleshooting for PC Windows based computers 33

KNOWLEDGE BASE 35

• Rocport ID5 Unique Features ___________________ ____________________ 35

• Specifications 35

• Introduction to Interfaces (ports) and Cables ________________________________ 36

o FireWire (IEEE 1394) 36

o USB (Universal Serial Bus) ____________________________________________ 38

o Comparison Chart __________________________________________________ 39

• Introduction to Formatting 40

o File Allocation Table (FAT) and FAT 32 __________________________________ 40

o HFS Plus or HFS+ 41

LIMITED WARRANTY 42

TECHNICAL SUPPORT 45

ACKNOWLEDGEMENTS 46

• Trademarks __________________________________________________________ 46

• Copyrights 46

CONTACT INFORMATION 47

• Corporate Headquarters ________________________________________________ 47

• Technical Support / Return Authorization “RMA” 47

• Sales Info ____________________________________________________________ 47

Page | 4

ROCSTOR

|

ROCPORT ID5

user manual

Safety Notices

• The warranty is void if an unauthorized person attempts and/or repairs the hard disk drive.

• Read all Manuals and instructions carefully before using the device.

• Do not spill any liquid or insert any object into the device.

• Use the device within the specifications indicated, including but not limited to: power

requirements, temperature, humidity, sunlight and magnetism from other devices such as

computers and televisions.

• Please visit the Rocstor website, www.rocstor.com for further information concerning

specifications and use of the device.

General Notices

• Consistently make multiple backup copies of your data for your protection. Hard disk drives

are subject to failure at any time.

• Rocstorage, Inc. shall not be held liable for loss of data or the restoration or recovery of

data on the device. Please view complete Limited Warranty Information in this manual or

on the Rocstor website (www.rocstor.com) for further details.

Capacity Disclaimer

Actual accessible hard drive capacity will indicate up to 10% lower than stated under different

Operating Systems and formatting.

The storage volume is measured in total bytes before formatting. References to round

numbers of gigabytes or terabytes are an approximation only. For example, a disk drive labeled

as having 500GB (gigabytes) has space for approximately 500,000,000,000 bytes before

formatting. After formatting, the drive capacity is reduced by about 5% to 10% depending on

the operating system and formatting used.

Care and Handling

The following instructions concern the proper care and handling of Rocport Drives. Please

take a moment to review these instructions.

• As with any storage solution, it is recommended that all data be backed up regularly.

• Ensure that you follow the proper removal procedure to disconnect the Rocport drive.

• Do not move or disconnect this device from your computer while it is reading or writing

data. This may cause damage to the Rocport drive.

• Do not place this device near a heat source or expose it to direct flame.

• Do not place the device near any equipment generating strong electromagnetic fields.

Exposure to strong electromagnetic fields may cause the device to malfunction or data to

be corrupted.

• Do not drop or cause shock to your Rocport drive.

• Do not spill any liquid or insert any object into the device.

Page | 5

ROCSTOR

|

ROCPORT ID5

user manual

• Do not attempt to disassemble and service the Rocport drive during the warranty

period.

• Please read the Safety Notices and Limited Warranty information in this Manual and on

the Rocstor website (www.rocstor.com) for further details.

Page | 6

ROCSTOR

|

ROCPORT ID5

user manual

Introduction

ROCPORT ID5 – FireWire 400 and USB (1.1/2.0)

Rocport ID pocket drives deliver outstanding performance and

reliability in multiple colors. Designed and engineered in the U.S.A.

to meet the needs of the demanding mobile data storage market,

the ROCPORT ID 2.5” external hard drive is compatible with both

Windows and Macintosh environments.

Like other Rocstor products, ROCPORT ID drives are both

bus-powered and bootable. The new ROCPORT ID pocket drives

contain a fast, high capacity 2.5” SATA drive mechanism, with up

to 480 MB/sec transfer speeds. Groundbreaking Design,

Sophisticated users will appreciate the ROCPORT ID innovative design, touch, quality and

features.

Choose Rocstor drives and “store your future”

Box Contents

• Rocport ID5 , external hard disk drive

• USB “Y” cable

• 6-pin to 6-pin FireWire 400 (1394a) cable

• Quick Installation user Guide

• Comprehensive manual on CD

• Carrying case

Page | 7

ROCSTOR

|

ROCPORT ID5

user manual

Minimum System Requirements:

Mac Users: Window Users:

* Many computers do not come with factory installed FireWire 800 ports. Therefore, you may

need to purchase a PCI, PCI-X or PCI-Express card to use these ports.

Connectors

• FireWire 400 (IEEE 1394a) port x2

• USB 2.0 port x1

Hardware: FireWire 400 or USB (1.1 or

2.0) port(s.)

Operating Systems: Microsoft Windows

2000, Me, XP, Vista, Windows 7

Recommended memory: 512 MB RAM

Hardware: FireWire 400 or USB (1.1 or

2.0) port(s.)

Mac: PowerPC or Intel processor running

Mac OS 9, X, Leopard, Snow Leopard

Recommended memory: 512 MB RAM

Page | 8

ROCSTOR

|

ROCPORT ID5

user manual

QUICK INSTALLATION

How to Connect the Interface Cables - Connecting the Drive

1. Turn ON your computer and wait until it fully boots up to load all programs.

2. Using only one interface cable at a time, select the interface port you wish to use on your

computer.

When using FireWire, connect one end of the FireWire 400 cable to the appropriate

FireWire 400 (1394a) port of your computer and then the other end to the FireWire port in

the Rocport ID5. When using USB, connect two ends of the USB “Y” cable to the USB ports

of your computer (or via Power Hub that is connected to your computer) and then the

other end to the USB port in the Rocport ID5. Upon connection, a Blue light on the Rocport

drive will turn ON.

3. The Hard drive is preformatted for Plug-and-Play operation. After a few seconds a Rocstor

HD icon will show on “My Computer” folder under the Windows OS. Under the Mac OS,

the Rocstor HD icon will appear on the “Desktop.”

4. Click (double click) on the Rocstor HD icon to access the drive.

*You may also refer to the Rocstor website to view or download a full version of the Rocport

ID5 manual. www.ROCSTOR.com

ROCSTOR

|

ROCPORT ID5

user manual

Cable Types:

FireWire 400 (IEEE 1394a) 6-

Pin FireWire 400 connector

• FireWire 400 can

transfer data between devices at 400

USB supports three data transfer rates:

• USB 2.0: A Hi-Speed

(USB 2.0) rate of 480

• USB 1.1: A Full Speed

rate of

• USB 1.0: A Low Speed

rate of 1.5

user manual

Pin FireWire 400 connector

transfer data between devices at 400

Mbits/s

USB supports three data transfer rates:

(USB 2.0) rate of 480

Mbits/s (60 MB/s).

rate of

12 Mbits/s (1.5 MB/s).

rate of 1.5

Mbits/s (187 KB/s).

Page | 9

Page | 10

ROCSTOR

|

ROCPORT ID5

user manual

Installing Your Drive

All Rocstor hard drives are formatted as blank FAT32 (32-bit file allocation table) volumes

{unless otherwise stated on the box} that are compatible with most modern Windows and

Macintosh operating systems. To begin using your Rocstor drive, simply connect a data cable.

There’s no need to shut down your computer because your Rocstor drive is hot-pluggable. Just

plug it in and it’s ready to use.

The first choice you have to make is which of the provided data cables to use. The drive can

connect directly to any available FireWire or USB port on your computer, or it can be Daisy-

Chained to your computer through another compatible device with an available FireWire port.

The ability to Daisy-Chain allows you to have multiple drives connected simultaneously, greatly

increasing your available storage capacity. Daisy-Chain is only available through FireWire ports.

If you intend to use the drive for additional storage only—not as a startup device (bootable) use

the cable that provides the maximum throughput rate for the buses available on your

computer: Up to 480 Mbits via USB 2.0, 400 Mbits via FireWire 400, or 12 Mbits via USB 1.1. To

avoid damaging your hardware and losing data, never simultaneously connect the drive to the

computer using more than one data cable.

Rocport ID5 as a bootable device

If you intend to use the drive as a startup device, check the documentation that came with your

computer to confirm compatibility with the various interfaces. PowerPC-based Macs require

FireWire connections for startup disks, whereas Intel-based Macs can use either FireWire or

USB connections.

Furthermore, using the drive as a startup device requires installing an authorized copy of the

Windows or Mac operating system (available separately from Microsoft and Apple,

respectively). To install the Mac OS 9 or OS X, you must reformat the drive as a Mac OS

Extended volume with Disk Utility. An Intel-based Mac cannot start from a device formatted on

a PowerPC-based Mac, or vice versa.

Disconnecting Your Drive

Never disconnect or turn off an external drive when its activity light is ON. External drives must

be properly unmounted (or disconnected) to avoid data loss and possible damage to the hard

disk drive or computer.

PC: The easiest ways to safely unmount an external hard drive on your PC is to right-click the

device removal icon next to the clock in the system tray. Then choose Safely Remove Hardware.

Choose the external device you want to remove, and then click Stop. An alert will notify you if

the drive is in use by an application. If in use close any open documents or applications on the

drive and try again. Windows will display an alert when you can safely disconnect or turn off the

drive.

Page | 11

ROCSTOR

|

ROCPORT ID5

user manual

Mac: The easiest way to safely unmount an external hard drive is to drag its Finder icon to the

Trash. An alert will notify you if the drive is in use by an application. Close any open documents

or applications on the drive and try again. When the drive’s icon no longer appears on the

Finder’s Desktop and the drive’s activity light is green, you can safely disconnect or turn off the

drive.

Reformatting Your Drive

As mentioned previously, all Rocstor hard drives are formatted as blank FAT32 volumes {unless

otherwise stated on the box} that are compatible with most modern Windows and Macintosh

operating systems. However, you can use your normal disk management tools to erase or

reformat the drive if needed. For example, Windows users may want to reformat the drive as

an NTFS (new technology file system) volume, or Mac OS X users may wish to reformat the

drive as a Mac OS Extended (Journal) or UFS (Unix file system) volume.

Please note that all of your data will be lost if the volume (Hard Drive) is formatted or reformatted.

Reformatting via PC (Window based computers)

Right-click the Rocport drive in the “My Computer” folder, then choose Format. In the dialog

window that appears, choose the desired capacity, file system and allocation unit size and then

click Start.

Reformatting via Mac

Open Disk Utility (/Applications/Utilities). Select the drive in the list at the left, then click the

Erase tab. Choose the desired volume format, specify a name, then click Erase.

Important Note

Any cable (FireWire 400, or USB 2.0) inserted before the drive is powered on has priority over

the other cables and will be the primary connection method, e.g. if the drive is connected via

FireWire 400 before powering on the drive, data will be transferred via FireWire 400.

The drive should only be connected to a computer via one interface at a time. Connection of the

drive to a computer via two or more interfaces is not recommended and may potentially

damage your Rocport drive and data.

Page | 12

ROCSTOR

|

ROCPORT ID5

user manual

How to Daisy-Chain through FireWire ports to your Rocport ID5 Drive at one

time

Daisy-Chain (Connecting Multiple Devices) means that device A is connected to device B and device

B is connected to device C and so forth. All connections are made only through FireWire ports.

• Do not mix interfaces. Select FireWire ports only. For example, do not use USB and

FireWire to Daisy-Chain.

• Mixing FireWire 400 and 800 connectors to Daisy- Chain will reduce the transfer speed to

FireWire 400.

• Daisy-Chain allows you to connect multiple devices, such as cameras, external read/write

drives and other external devices such as hard disk drive to your computer via FireWire

ports.

Page | 13

ROCSTOR

|

ROCPORT ID5

user manual

PARTITIONING AND FORMATTING THE ROCPORT ID5 DRIVE ON A MAC OS

All Rocstor drives are factory formatted with FAT32, unless otherwise stated on the retail box.

WARNING: Formatting and Partitioning the Rocport Drive will destroy all of its data. To

protect your data, back it up before formatting or partitioning this device.

IMPORTANT NOTES:

1. All programs should be closed before beginning.

2. Connect the Rocstor hard disk drive to your computer using (one) appropriate cable.

3. Rocport is bus-powered through FireWire ports and turn ON automatically. With USB

connections you may need to connect to more ports to receive enough power depending

on your computer. When connecting the Rocport drive with a USB port, certain laptop

computers may not provide enough power to operate the drive. To overcome this

problem, connect the Rocport drive using a USB Y-connector or use an external power

source. This problem is likely to occur when using certain brands of laptop computers.

4. “Click” means left click. “Right Click” will be so labeled.

5. Some computers are set so a single “click” will perform the task, such as opening a

window. Depending on your mouse setting, you may have to double click to get to the

next window. If a single click does not open the next window, please double click.

ROCSTOR

|

ROCPORT ID5

user manual

INSTRUCTIONS FOR PARTITIONING AND

1.

Connect the Rocstor drive to the computer via a port.

2.

The drive will appear as an icon on the Desktop on the middle right side. The icon will

represent the method of

connection (USB

Note: If the Hard Drive is connected via USB port, the desktop would indicate the USB

“Macintosh HD” icon.

The same procedures would also apply to the following steps.

user manual

INSTRUCTIONS FOR PARTITIONING AND

FORMATTING FROM FAT32 to HFS+:

Connect the Rocstor drive to the computer via a port.

The drive will appear as an icon on the Desktop on the middle right side. The icon will

connection (USB

or FireWire).

Note: If the Hard Drive is connected via USB port, the desktop would indicate the USB

The same procedures would also apply to the following steps.

Page | 14

The drive will appear as an icon on the Desktop on the middle right side. The icon will

Note: If the Hard Drive is connected via USB port, the desktop would indicate the USB

on the

The same procedures would also apply to the following steps.

ROCSTOR

|

ROCPORT ID5

user manual

3.

Once the icon appears on the

4.

In the “Macintosh HD” menu, click on the “Applications” icon.

user manual

Once the icon appears on the

“Desktop”

click on the “Macintosh HD” icon.

In the “Macintosh HD” menu, click on the “Applications” icon.

Page | 15

click on the “Macintosh HD” icon.

ROCSTOR

|

ROCPORT ID5

user manual

5. If you are using

Tiger, click on Options on the lower center of the window. Select the

Partition Scheme for your Rocstor drive. Suggest you select “Apple Partition Map” then

click OK.

user manual

Tiger, click on Options on the lower center of the window. Select the

Partition Scheme for your Rocstor drive. Suggest you select “Apple Partition Map” then

Page | 16

Tiger, click on Options on the lower center of the window. Select the

Partition Scheme for your Rocstor drive. Suggest you select “Apple Partition Map” then

ROCSTOR

|

ROCPORT ID5

user manual

6.

Volume Information: select a name for your drive.

7.

Format: Click on either the “Format” area or the Blue up/down arrows. Select Mac OS

extended (journal).

user manual

Volume Information: select a name for your drive.

Format: Click on either the “Format” area or the Blue up/down arrows. Select Mac OS

Page | 17

Format: Click on either the “Format” area or the Blue up/down arrows. Select Mac OS

ROCSTOR

|

ROCPORT ID5

user manual

8.

After selecting the type of format, click the “Partition

screen. On the next screen,

user manual

After selecting the type of format, click the “Partition

” tab in the lower right of the

screen. On the next screen,

“Partition Disk”

, click “Partition” again.

Page | 18

” tab in the lower right of the

, click “Partition” again.

ROCSTOR

|

ROCPORT ID5

user manual

9.

The drive will begin to format and upon completion; the same icon that first appeared on

the Desktop will reappear with your designed name on the Desktop.

10. Exit.

user manual

The drive will begin to format and upon completion; the same icon that first appeared on

the Desktop will reappear with your designed name on the Desktop.

Page | 19

The drive will begin to format and upon completion; the same icon that first appeared on

Page | 20

ROCSTOR

|

ROCPORT ID5

user manual

PARTITIONING AND FORMATTING THE ROCPORT ID5 DRIVE ON WINDOWS 2000, XP AND

VISTA

All Rocstor drives are factory formatted with FAT32, unless otherwise stated on the retail box.

WARNING: Formatting and Partitioning the Rocport Drive will destroy all of its data. To

protect your data, back it up before formatting or partitioning this device.

IMPORTANT NOTES:

1. All programs should be closed before beginning.

2. Connect the Rocstor hard disk drive to your computer using the appropriate cables.

3. Rocport is bus-powered through FireWire ports and turn ON automatically. With USB

connections you may need to connect to more ports to receive enough power depending

on your computer. When connecting the Rocport drive with a USB port, certain laptop

computers may not provide enough power to operate the drive. To overcome this problem,

connect the Rocport drive using a USB Y-connector or use an external power source. This

problem is likely to occur when using certain brands of laptop computers.

4. The initial goal is to reach the Control Panel. If you know how to get there, skip this section

and go directly to Instruction 1 (Instructions for Partitioning and Formatting From FAT 32 to

NTFS).

5. The ultimate goal is to reach Disk Management. If you know how to get there, skip this

section and go directly to Instruction 4 (Instructions for Partitioning and Formatting From

FAT 32 to NTFS).

6. Due to different views that are possible on Windows operating systems (2000, XP, Vista),

we will provide various ways of reaching the Control Panel.

7. “Click” means left click. “Right Click” will be so labeled.

8. Some computers are set so a single “click” will perform the task, such as opening a window.

Depending on your mouse setting, you may have to double click to get to the next window.

If a single click does not open the next window, please double click.

Page is loading ...

Rocstor Rocport ID 5 320 GB User manual

Rocstor Rocport ID 5 320 GB User manual

Related papers

Other documents