LevelOne HVE-0201 User manual

Category
AV extenders
Type
User manual

LevelOne HVE-0201 is a high-performance HDMI extender that utilizes fiber optic cables to transmit uncompressed HDMI signals over long distances, supporting resolutions up to 1920 x 1080. It eliminates RF interference and provides reliable signal transmission, making it suitable for various applications such as digital signage, home theaters, and conference rooms.

LevelOne HVE-0201 is a high-performance HDMI extender that utilizes fiber optic cables to transmit uncompressed HDMI signals over long distances, supporting resolutions up to 1920 x 1080. It eliminates RF interference and provides reliable signal transmission, making it suitable for various applications such as digital signage, home theaters, and conference rooms.

HVE-0201
HDMI Extender via Fiber Channel
User Manual
V1.0
1
Introduction
LevelOne HVE-0201 HDMI extender uses 2 cores
fiber without any copper wire inside, where radio
frequency interference phenomenon is literally ruled
out, which shows the advantage of high performance
and good signal quality as well as low cost. Optical
fiber is of low dispersion, which in turn has the
strength of longer signal transmission distance and
better signal transmission quality in comparison to the
traditional copper wire cable.
Feature
Long distance video and audio transmission
High resolution and image quality
Supports resolution 1920 x 1080, up to 200m
HDCP fully compliant without copper wire
No RF Interference by optical fiber
HDMI Type A connection
2
Package Content
HVE-0201 (RX+TX)
Power Adapter (DC5V, 1.0A)
HDMI Cable
User Manual
Hardware Description
Dimension / Weight
95 x 145.8 x 25.8mm (W x D x H), 400g
3
Front Panel
Note:
Signal between Source and Sink also referred to as
the source(TX) and receiving(RX) devices
Rear Panel
Power
Jack
HDMI
Connector
SC
Fiber
Optical
Fiber
Power
LED
HDMI
Source
HDMI
Sink
4
Installation
1. Put ‘TX module near to HDMI signal source, such as
DVD players or computers.
2. Put ‘RX’ module is near to HDMI sink, such as LCD
TVs or Projectors.
3. Connect two place by using multimode fiber of 2
cores.
4. Scour the all end face of fibers. (See Note 1)
5. Plug in the fibers according to the indicated number.
The ‘1’,’2’.
6. Plug in the 5V adapter to the electricity and TR/RX
modules.
7. Link TX module to HDMI source by a HDMI cable.
(See Note)
8. Link RX module to HDMI sink by a HDMI cable. (See
Note)
Note
1. Clean end face of fiber before plugging in. The dust
will cause damage to the fiber.
2. The length of HDMI cable should be NOT longer than
2 meters.
3. These three figures in front of the modules represent
linking status. These 3 LEDs blaze green if all setup is
complete and correct. The left one stands for the
connection of fiber. The middle one stands for the
connection of HDMI source. The right one stands for
the connection of HDMI source.
5
Connection Diagram
System Requirement
HDMI Source (DVD player or PC)
HDMI Sink (Monitor or Projector)
100~240VAC 50~60Hz 0.2A electricity
HDMI Cable
Multi-mode
SC Fiber, 200m
DVD Player
TX RX
6
Technical Specification
Model
HVE-0201
Max Length
200M, 62.5, 50/125 MMF 2-SC
Max Resolution
1920 × 1080
HDCP Compliant
Yes
CEC Compliant
Yes
Max Power
Consumption
TX: 5V 3W, 600mA
RX: 5V 3W, 600mA
Power
DC 5V, 1.0A
Dimension
95 x 145.8 x 25.8mm (W x D x H)
Weight
400g
Operating Temp.
0 to 50
Storage Temp.
-20 to 75
EMI
CE, FCC
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

LevelOne HVE-0201 User manual

Category
AV extenders
Type
User manual

LevelOne HVE-0201 is a high-performance HDMI extender that utilizes fiber optic cables to transmit uncompressed HDMI signals over long distances, supporting resolutions up to 1920 x 1080. It eliminates RF interference and provides reliable signal transmission, making it suitable for various applications such as digital signage, home theaters, and conference rooms.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI