Haier 29F9B Operating Instructions Manual

MAIN FUNCTION

29T9B

29F9B

Colour Television

Operation Instructions

◆218 Programs stored

◆Dynamic noise reduction

◆Multi-picture modes, multi-sound modes selection

◆Auto-correcting black balance

◆Surround stereo

CONTENTS

WARNING AND CAUTIONS

BASIC FEATURE

TECHNICAL SPECIFICATION

FUNCTION BUTTONS AND EXTERNAL SOCKETS

REMOTE CONTROLLER BOARD

OPERATING MENU

MULTI FUNCTION TIMER

GENERAL OPERATION

TELETEXT FUNCTION

EXTERNAL CONNECTIONS

AV SIDE PANEL CONNECTION DIAGRAM

TROUBLESHOOTING GUIDE

1

2

3

5

6

10

12

14

15

16

17

BASIC FEATURE

TECHNICAL SPECIFICATION

●218 programs stored

●Auto-correcting black balance

●Surround stereo

●Blue extension, Green improvement

●Multi-picture modes and multi-sound modes

●Fast teletext

●Audio/Video input, S-VHS input

●Double SCARTS

WARNING AND CAUTIONS

1. When you clean the TV set, please pull

out the power plug from AC outlet.

Or may result in electric shock, fire or

damage to the TV set. Don't clean the

cabinet and the screen with benzene,

petrol and other chemicals.

4. Do not place the TV set near rain

or moisture as it may cause an electric

shock, or the TV set to catch fire. The TV

set must only be used

in dry indoor

location.

2. In order to prolong the using life of the

TV set, please place it in a well ventilated

location.

5. The back cover must only be removed

by a registered electrical service person.

Removing the back cover may result in

electric shock, fire or damage to

the TV set.

3. Don't place the TV

set in direct sunlight

or near heat source.

6. If the TV set is not going to be used for

long time, or there is a severe thunder &

lightening storm, it is recommended that

the TV set be disconnected from the AC

power outlet and the aerial plug

removed.

Explanation on the display tube

Should the picture tube require cleaning, disconnect the power and use a dry

soft cotton cloth. Do not use any cleaner or abrasive cloth.

1

2

POWER SUPPLY: See rating plate

TV SYSTEM: B/G DK

COLOUR SYSTEM: PAL SECAM NTSC3.58/4.43 (AV)

CRT: 29"

AERIAL INPUT IMPEDANCE: 75Ω unbalanced

VIDEO INPUT: 1.0VP-P(75Ω)

AUDIO INPUT: 436mVrms(40KΩ)

VIDEO OUTPUT: 1.0VP-P(75Ω)

AUDIO OUTPUT: 436mVrms(≥600Ω)

AUDIO MAX OUTPUT POWER: 5W+5W

POWER CONSUMPTION: See rating plate

NET WEIGHT(kg): 41(29T9B-P) 45(29F9B-P)

NET SIZE(mm): 810×530×600

Supplied accessories:

Infrared remote control handset 1

Battery(AA) 2

Operating instructions 1

Design and specifications are subject to change without notice.

AUDIO-R

AUDIO-L

VIDEO

AUDIO-R

AUDIO-L

VIDEO

Antenna

4

FUNCTION BUTTONS AND EXTERNAL SOCKETS

Figure A Figure B

Antenna cable

with a plug

Figure C

Figure D

Antenna feeder

Antenna adapter

75-300Ω

Coaxial cable(75Ω) twin-lead cable(300Ω)

Antenna Connection

Connect an antenna to the antenna socket on

the TV set,we recommend using a Cable TV

system for better picture and audio quality.

1.If you use a coaxial cable(75 ),insert the

antenna plug (see figure C) into 75 socket

(see figure A).

2.If you use a twin-lead cable(300 ),please

shape the cable as figure D,and connect the

leads to antenna adapter and then insert the

antenna adapter into the 75 socket.(see

figure B)

Power source wire connection

Insert the power plug into AC outlet.

To install and to replace batteries of the remote

control unit

1.Place the remote control unit with the face

down, then open the battery cover of the unit.

2.Place the two"AA"size batteries, matching

the + and - signs on each battery to the +

and -signs of the battery compartment.

3.Close the cover of the battery compartment.

NOTE:

(1)Don't drop or wet or dismantle the unit.

(2)If you don't intend to use the unit for a

long period or the electricity of the

batteries is used up, remove the batteries

to prevent batteries acid from leaking into

the battery compartment.

(3)Always replace both batteries at the same

time.

(4)Do not use rechargeable batteries (Ni-cd)

or mix battery types.

(5)Never place batteries in a fire. Dispose

of the batteries with your domestic

rubbish collection.

Ω

FUNCTION BUTTONS AND EXTERNAL SOCKETS

3

1.Front panel

(1)S-VHS input

(2)SCART1 socket

(3)SCART2 socket

(4)Antenna input

SCART1

SCART2

S-VHS

(3)

(2)

(4)

(1)

(2)

(3)

(1)

(5)

(6)

(7)

(4)

MENU

V-

V+ P- P+

TV/AV

(1)Remote sensor: let the remote controller aim here the set can receive remote

control signal.

(2)Power switch: press the button to turn on the TV set . press the button again to turn

off the TV set.

(3)Power indicator: the indicator lights in standby status ,the indicator lights in sleep

status . The indicator glints when you use remote controller.

(4)Menu button

(5)Program up/down button

(6)Volume up/down button

(7)TV/AV

2.Rear Panel

MARK

FUNCTION DESCRIPTION

MUTE

STANDBY

ONE DIGIT SELECTION

ONE OR TWO OR THREE DIGITS PRE-SELECTION

TV/VIDEO SELECTION

MENU DISPLAY

VOLUME CONTROL

CHANNEL NUMBER UP/DOWN

0-9

-/--

TV/AV

MENU

SWAP

-VOL+

-CH+

PICTURE MENU

PICTURE

SOUND MENU

SOUND

TIME MENU

TIME

FUNCTION MENU

FUNCTION

1

2

3

5

4

X

T

EI

DP

.

ST

.SD

S

T

C

AN

S

A

S

W P

T

P

I R

C

U

E

O

L

-

V

C

H

+

O

L

V +

C H

-

E

MU

T

6

O

N

D

M

N

TI N

E

S

U TI

E U

C

O

N

F TU

9

7

8

T

V

AV

/

-/-

-

Z

OOM

CLAL

0

I

- I

.

PP

M

E

NU

?

T

M

U

E

S A

C

N

PROGRAM SCAN

O

Z

M

O

Z

OM

C

A

L

D

I

P

A

Y

S

I

E

X

T

I

I-

I

TD

P

S.

T

S

.

S

D

E

N

TU

??

TELETEXT SUBTITLE

IT IS ONLY VALID IN AV MODE

PICTURE MODE SELECTION

SOUND MODE SELECTION

TUNE MENU SELECTION

TV/TELETEXT ENTERING/EXITING

TO REVEAL CONCEALED TELETEXT

TELETEXT ZOOM

TELETEXT PAGE HOLD

TELETEXT/TV MIX MODE

TV/TELETEXT ALTERATION

TIME DISPLAY(IN TV MODE)/SUBCODE SWITCH

EAST/WEST

EXIT MENU DISPLAY

REMOTE CONTROLLER BOARD

OPERATION MENU

5

6

1.Entering and exiting menus

Press MENU button on the remote controller once (or directly

press PICTURE button on the remote controller), PICTURE

menu displays on the screen; press MENU button

twice (or directly press SOUND button on the remote

controller), SOUND menu displays on the screen .

Press the menu button again (3 times, or directly press

TIME button on the remote controller), TIME menu displays

on the screen. Press the menu button again (4 times, or directly press FUNCTION button on the

remote controller), FUNCTION menu displays on the screen. Press the menu button again (5

times or directly press TUNE button on the remote controller), TUNE menu displays on the

screen. Press the menu button again (6 times), EXCHANGE menu displays on the screen .To

turn off the on-screen menu display, either press the EXIT button or allow the TV set to

automatically turn off the menu by not pressing any buttons for a few seconds.

2.Auto search

A. Press MENU button five times (or directly press TUNE button on the remote

controller), e

Press MENU button five times (or directly press TUNE button), ensure that the

TUNE menu is displayed. Press the CH+/- buttons to select SEARCH. Then press the VOL+

button to search up or V- button to search down to the next TV station.(It is much faster to

search up.)If the wrong station is found ,press the search button again. You may need to

repeat this until the correct station is located. To store the new program, press the EXIT

button.

4.Fine tune

If the picture or sound is poor, try to use the "FINE TUNE" feature. Select the

FINE TUNE by using the CH +/- buttons. Use the VOL +/- buttons to fine-tune the

sound and picture for optimum results. Then press the EXIT button to store the

results. Do not use this feature unless reception is poor.

nsure that the TUNE menu is displayed. Press the CH+/- buttons to select

AUTO SEARCH. Then press the VOL+button, the TV set will begin to search programs

from present programme No..

B. After the search has finished, the TV set will return to the first program stored.

3. Search

5.Selecting the sound system

Press the CH+/- buttons to select SOUND item. Then press the VOL+/- buttons to select a

sound system you need.

TUNE

COLOUR AUTO

SOUND B/G

BAND VHFL

SKIP OFF

PROGRAM 19

SEARCH

FINE TUNE

AUTO SEARCH

6.Selecting colour system

Usually this should be set in the auto position. However if the colours displayed on

the screen are incorrect you can manually select the correct colour system. When

you have finished remember to turn it back to auto again so that other programs

will still work correctly. Use the CH+/- buttons to select COLOUR then the VOL+/-

buttons to select a colour system you need. Press the EXIT button to save the setting.

Setting channels

NOTE：

Use CH+/- or VOL+/ -buttons, either on the remote controller or on the front panel

of the television to navigate menus and to select menu options.

RECALL PREVIOUS PROGRAM

OPERATION MENU

8

Press the MENU button once or press the PICTURE

button on the remote controller to display the PICTURE

setting menu.

1.Contrast (adds depth to the picture)

Press the CH+/- buttons to select CONTRAST, then

press the VOL+/- buttons to adjust the contrast level.

2. Brightness (adds sparkle and shine to the picture)

Press the CH+/- buttons to select BRIGHTNESS, then press the VOL+/- buttons

to adjust the brightness level.

3. Colour (adds colour depth)

Press the CH+/- buttons to select COLOUR, then press the VOL+/- buttons to

adjust the colour level.

4. Sharpness (adds fine detail)

Press the CH+/- buttons to select SHARPNESS, then press the VOL+/- buttons to

adjust the sharpness level.

Note: Do not turn the sharpness up to high if the reception is poor or has lots of

noise as it will enhance the fine grain details.

5. Black stretch (adds deeper blacks and increases the contrast range)

Press the CH+/- buttons to select BLACK STRETCH, then press the VOL+/- buttons

to turn this feature on/off.

6.Hue

Press the CH+/- buttons to select HUE, then press the VOL+/-buttons to adjust

the hue level.

Note: Hue is only used in the AV mode.

7.Program skip

The Program skip feature enables you to skip/hide programs that you do not

wish to be displayed when using the CH+/- buttons. These channels will still

be displayed by directly using the channel number buttons on the remote

controller. To skip, press the CH+/- buttons to select the SKIP menu, press the

VOL+/- buttons to tune the skip feature on/off. Press the EXIT button to save

the setting.

8. Program number

The program number is the remote control channel number. You can change the

program number to see channels stored without exiting this main menu. Press the

CH+/- buttons to select PROGRAM, press the VOL+/- buttons to change the program

number that you are adjusting.

9. Band switching (Note: This is a new item.)

If you already know what band the channel is on, tuning can speed up by

selecting the correct band before going into the search menu. This feature

should only be used if you understand the channels in your local area.

Picture Adjustments

PICTURE

CONTRAST 89

BRIGHTNESS 66

COLOUR 50

SHARPNESS 50

BLACK STRETCH OFF

IIIIIIIIIIIIIIIIIIIIIIIII..........

OPERATION MENU

7

Sound Adjustments

Press the MENU button twice or press the SOUND button on the remote controller

to display the sound setting menu.

2.Bass (add low frequency depth)

Press the CH+/- buttons to select BASS, then

press the VOL+/- buttons to adjust the

bass level.

3.Treble (add high frequency clarity)

Press the CH+/- buttons to select TREBLE, then

press the VOL+/- buttons to adjust the treble

level.

4.Balance (selects between the left and right

stereo channel levels)

Press the CH+/- buttons to select BALANCE,

then press the VOL+/- buttons to adjust the

balance level.

5.Surround (enhances the stereo effect by

making the sound appear wider)

Press the CH+/- buttons to select

SURROUND, then press the VOL+/- buttons

to turn this feature on/off.

1 .Volume (adjust the loudness level)

Press the CH+/- buttons to select VOLUME,

then press the VOL+/- buttons to adjust the

volume level.

SOUND

VOLUME 50

BASS 50

TREBLE 50

BALANCE 0

IIIIIIIIIIIIIIIIIIIIIIIII..........

SURROUND OFF

TIME

CLOCK --:--

ON TIME --:--

ON-PROG 1

OFF TIME --:--

SLEEP TIMER --:--

REMIND TIME --:--

REMIND PROG 1

FUNCTION

ENGLISH

BACKGROUND ON

NOISE REDUCE OFF

FADE ON

CHILD LOCK OFF

AVL OFF

CALENDAR

OPERATION MENU

MULTI FUNCTION TIMER

9

10

5.Child lock (enables the TV front control buttons to be locked)

Press the CH+/- buttons to select CHILD LOCK, then press the VOL+/-

buttons to turn this feature on/off.

6.AVL (Automatic Volume Limit control reduces effect of large volume

changes such as when the ads come on.)

Press the CH+/- buttons to select AVL, then press the VOL+/- buttons to turn this

feature on/off.

7.Calendar (enables the TV sets internal calendar to be set)

Press the CH+/- buttons to select CALENDAR, then press the VOL+/- buttons

to select the item to be changed and the CH+/- buttons to alter each setting.

2.Background (If the signal is very poor or there is no

input signal the picture will mute to black.)

Press the CH+/- buttons to select BACKGROUND,

then press the VOL+/- buttons to turn this feature

on/off.

3.Noise reduce (Picture Noise & Grain reduction circuit)

Press the CH+/- buttons to select NOISE REDUCE, then

press the VOL+/- buttons to turn this feature on/off.

4.Fade

The FADE control allows time for the picture tube to warm up and gently

turned on, which can help prolong the life of the picture tube.

Function Menu

Multi Function Timer

The TV set has built a comprehensive timer

that there are five basic functions.

1.Clock

2.On time so that the TV set can be programmed

to turn on at a certain time.

3.Off time to allow the TV set to turn off at a

preset time.

4.Sleep timer to allow the TV set to turn off after

10 ~ 180 minutes.

5.Program remind timer, that displays an on-

screen reminder prompt, when a program on a

different channel is due to start.

Selecting the clock menu

Press the MENU button continually until the TIME menu is displayed or press

the yellow time button on the remote controller.

1. Clock (master timer clock)

Press the CH+/- buttons to select CLOCK, then press the VOL+/- buttons to

adjust the hour. Press the CH- buttons to select minute and the VOL +/- buttons to

adjust the minute.

2. On Time

Press the CH+/- buttons to select ON TIME, then press the VOL+/- buttons to

adjust the hour. Press the CH- button to select minutes and the VOL+/- buttons to

adjust the minutes. Press the CH- button to select ON-PROG and the VOL+/-

buttons to select the TV channel that the TV set will automatically turn on to.

3. Off Time

Press the CH+/- buttons to select OFF TIME, then press the VOL+/- buttons to

adjust the hour. Press the CH- button to select minute and the VOL+/- buttons to

adjust the minute.

4. Sleep Timer

Press the CH+/- buttons to select SLEEP TIMER, then press the VOL+ button

Note: The clock will only work in the TV set if left turned on or in standby.

When the set is disconnected from the power supply or is turned off by

the main power switch on the front panel, the clock looses power and

will need to be reset when the power is reconnected.

1.Language selection

Press the CH+/-buttons to select LANGUAGE, then

press the VOL+/-buttons to select an OSD language

you need.

EXCHANGE

PROGRAM 1 1

PROGRAM 2 1

EXCHANGE

MULTI FUNCTION TIMER

GENERAL OPERATION

11

12

to adjust the amount of time before the TV set will automatically turn off. Each time

the VOL+ button is pressed the sleep time will increase by 10 minutes. The

maximum sleep time is 180 minutes.

5. Remind Time

Press the CH+/- buttons to select REMIND TIME, then press the VOL+/- buttons to

adjust the hour.

Press the CH- button to select minute and the VOL +/- buttons to adjust the minute.

Press the CH- button to select REMIND PROG and the VOL +/- buttons to select the

TV channel that the TV set will automatically remind you to turn to while watching

another channel.

Program Number Exchange

This feature enables TV programs that

may be on a wrong TV channel number

to be swapped/exchanged. This feature

is very useful when Automatic Search

Tuning has been used, to reallocate the

found programs to the correct channel

numbers.

Press the MENU button 6 times until the

exchange menu is displayed.

Press the CH+/- buttons until program 1 is

selected. Use the VOL+/- buttons to

select the channel number to be swapped.

(I.E If you wish to exchange channel 2

and 4 PROGRAM 1 should = 2.)

Press the CH+/- buttons until program 2 is

selected. Use the VOL+/- buttons to

select the channel number to be swapped.

(I.E If you wish to exchange channel 2

and 4 PROGRAM 2 should = 4.)

Press the CH+/- buttons until EXCHANGE is

selected. Press the VOL+ button to enable

the exchange.

1.Channel Changing (218 possible channels)

Use either the CH+/- buttons on the remote controller or the front panel of the TV set

to change the channels. Or directly enter the channel number with the numeric button

on the remote controller.

2.Volume Adjustment

Press the VOL+/- buttons on the remote controller or the front of the TV set to adjust

the volume level. The range is 0~100. When the volume buttons are pressed, the

volume level is displayed automatically on the TV screen.

3.Standby

Using the remote controller the TV set can be placed into standby mode.

A red standby light will glow on the TV front panel when the TV

set is placed into standby. To turn the TV set back on again, press standby button

on the remote controller again. It will take a few seconds before a picture is

displayed.

4.Mute

Press the MUTE button on the remote controller to mute the TV set sound. Pressing

the MUTE button again will turn the sound back on again.

5.Preset Picture Modes

Our engineers have designed in 5 commonly used picture settings to allow fast

picture level selection depending on what type of TV program is showing. Each

mode is selected in turn by pressing the "P. STD" button on the remote controller.

The 5 modes are:

Listen- This is a new feature that blacks out the TV screen when listening to

music only channels.

Soft - Designed for night time low light viewing.

Standard - Designed for rooms that have good all round lighting.

Rich - Designed for rooms with high ambient lighting such as daytime sport.

User- A spare setting that can be adjusted to personal tastes.

All the 5 modes can be independently adjusted by using the PICTURE

adjustment menu.

Press repeatedly the [-/--] button to select the appropriate number of digits for

the next program number that you want to watch. The on screen indication will

change sequentially between one digit (-) for 0 to 9, two digits (- -) for 10 to

99 and 3 digits (- - -) for 100 to 218 input selection. After selecting the number

of digits, simply press the numeric keys for the desired program number. For

example, to select program 34, press the button [- / - -] until the on screen

indication shows (- -), then press 3 and finally 4.

Standby

mode must be used when the timer has been set to turn on the television

automatically.

13

14

1.TV/Teletext Button (Turns the Teletext feature On/Off) [ ]

Press the [ ] button on the remote controller to turn teletext On/Off.

To select a teletext page either directly enter the page number using the numeric key

pad on the remote control or use the CH+/- buttons, or the coloured Fast Text buttons.

2.Mix Mode [ ]

While in Teletext mode press the [ ] and will show the teletext data

superimposed on top of the TV picture. Press the button again to revert back to Full

text.

3.Cancel Mode [ ]

This feature allows the TV picture to be displayed while next page to be searched is

entered and found. Only the top teletext line is displayed until the page is found.

Press the [ ] button to hide the teletext information. Either press the [ ]

(Cancel button) or the [ ] (Text button) to exit the cancel display mode.

4.Language Mode [ ]

Pressing the [ ] button will change the Teletext characters between Eastern and

Western.

5.Hold [ ]

Pressing the [ ] button will stop the teletext page automatically updating.

This feature is very useful where there are several teletext pages on the same

page number.

6.Size [ ]

Pressing the [ ] button changes between full screen top half bottom and

half full screen. This feature is very useful as it magnifies the image

making the characters easier to read.

7.Reveal [ ]

Pressing the [ ] button will reveal hidden text. This feature is used to

reveal information such as answers to teletext on-line interactive puzzles.

?

TELETEXT FUNCTION (FAST TEXT)

GENERAL OPERATION

8.Subtitle [ ]

Pressing the [ ] button will get the teletext decoder to automatically

search for the subtitle page.

9.Time [ ]

While in normal TV mode only, pressing the [ ] button will display the

teletext time in the top right hand corner for a few seconds. In teletext

mode, the button can be used as sub-code switch.

6.Preset Sound Modes

Our engineers have designed in 4 commonly used sound modes to allow the

best possible sound to be selected quickly. Each mode is selected in turn by

pressing the "S.STD" button on the remote controller.

The 4 modes are:

Speech- Designed to reduce the bass and treble which enhances the voice for

news programs.

Theatre- Enables extra bass and treble to enhance the movie experience.

Music- Adjust the sound to best suit music programs.

User - A spare setting that can be adjust to personal tastes.

All the 5 modes can be independently adjusted by using the PICTURE

adjustment menu.

7.Recall (on-screen display)

The CALL button on the remote controller allows the on-screen menu to be

displayed, showing the channel numbers and colour system and sound system.

8.Program Scan (Automatically increments/scans the channels and displays

each channel for a short time.)

The SCAN button on the remote controller

turns on/off the scan feature.

9.Zoom (changes the picture size format)

Each time the ZOOM button is pressed, the picture size will change. There are

3 size options:

Normal - Used for standard 4:3 picture programs.

16:9 - Automatically reduces the height so that the TV set

displays wide screen type image.

Enlarge - Zooms the picture in to magnify smaller images.

10.Channel Swap (toggles between the last channel view and the

current channel)

Each time the SWAP button is pressed, the last channel view is displayed.

11.AV Input Selection

Each time the TV/AV button is pressed, the input selection will cycle among

TV- AV1- AV2- SVHS- RGB- TV.

Notes: I.AV1 & SVHS share the same AV1 audio input.

Ⅱ.In AV modes the RECALL status display will only display the colour

system.

10.Fast text coloured buttons

Fast text automatically displays the four most commonly used pages that the

broadcaster thinks that you may want to choose next. Press the same coloured

button on the remote as the coloured link at the bottom of the teletext page

to go directly to that page.

TELETEXT FUNCTION (FAST TEXT)

15

16

VCR etc.

SCART1

SCART2

S-VHS

Note:

1.SCART1 & the Side Front AV panel are connected together. Only connect

to one of the inputs at any time.

2.The S- VHS input on the rear cover is connected to the Side AV panel.

3.SCART 2 has RGB, AV on the same input.

4.If you need to connect AV output, please select SCART1 terminal.

EXTERNAL CONNECTIONS

AV SIDE PANEL CONNECTION DIAGRAM

To videc output

To audio(L) output

To audio(R) output

To videc output

To audio(L) output

To audio(R) output

VCR or VCD etc. Camera

AUDIO-R

AUDIO-L

VIDEO

To audio(R) input

To audio(L) input

To video input

17

To assist in location possible faults use help guide below:

BREAKDOWN PHENOMENON

PICTURE

SOUND

CHECKING

the aerial direction and connection

volume、sound mute

Ensure that the power supply is connected to

the TV set and turned on. Also ensure that the

TV set is not in "Listen Mode" or that the

brightness and contrast are not turned down.

adjust color control

adjust channel again

Picture with Snow

Noise

Color Spot

Normal Volume

Scramble

Normal or Weak Volume

No Color

Normal Volume

No Picture

No Sound

Normal

Disturb

Noise

Double or Triple Image

Note:

1.If the fault can not be repaired by using above guide consult with your local authorized service center.

2.The TV set must only be repaired by a qualified registered service person. Never attempt to remove

the back cover as the TV set has dangerous voltages in side that may cause a fatality or fire.

3.The cabinet may produce the occasional "snapping sound" This is normal and caused by the

materials in the cabinet expanding with room temperature changes.

TROUBLESHOOTING GUIDE

Electrical interference which can be caused by

cars, motorbikes etc, fluorescent lamps and

dirty insulators on overhead power cables.

This is called ghosting which can be minimized

with an outside aerial, and good quality cable

and terminations. Altering the aerial direction

can also minimize this effect.

Colour purity fault which can be caused by moving

the TV set, placing magnets near the TV screen or

turning on/off house hold appliances such as

vacuum cleaners near the TV set. Turn the TV off

with the mains power switch for 15 minutes.

When the power is turn on again the TV set will

automatically demagnetize the picture. In severe

cases leave the TV set turned off overnight.

Haier 29F9B Operating Instructions Manual

This manual is also suitable for

Haier 29F9B Operating Instructions Manual

Related papers

Other documents