Lightolier IS:1155 User manual

Brand: Lightolier

Model: IS:1155

Type: User manual

Lightolier IS:1155 is a lighting fixture designed to be installed in a ceiling. It can be used with a variety of different reflector trims, including eyeball trims and adjustable accent light trims. The fixture is compatible with both 12v and 5.5v lamps, and the voltage can be easily adjusted using a slide switch. The fixture also comes with a male adapter that allows it to be screwed into a standard socket.

The Lightolier IS:1155 is a versatile and easy-to-install lighting fixture that can be used in a variety of different applications. It is perfect for use in homes, offices, and retail stores.

INSTRUCTION SHEET NO.

lN=ALLATION OF LYTECA~ER REFLEOTOR TRIM

IN THE 1100 SERIES FRAME-IN-KIT WITH ROTO CLIPS

IS:1155

R0487

READ AND UNDER~AND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.

This fixture is intended for installation

in accordance with the National Electrical Cods and local or federal

code specifications. To prevent electrical shock, turn off electricity at fuee box before proceeding.

NOTE Use this Instruction Sheet only when Lytecsster Trim is being Installed in the 1100 series Frsme-im

Kits with Roto Cfips (see Fig. F). If not, disregsrd this Instruction Sheet.

FIG. A

FIG. B

FIG. C

FIG. D

FIG. E

1. FRAME-fN

2. ROTATE CLIPS

3. SCREW4N

4. SNAWN

PUSH.UP

WARNING: BEFOREinstalling REFLECTORTRiM lU FRAME-fN Km,READ MARKINGS IN REFLECTORTRIM

AND IN SOCK= CUP OF FRAME.fN-KIT TO D~ERMINE LAMP WAT7AGE

AND TYPE APPLICABLE FOR YOUR

lNSTALLATfON. IF IC. TYPE FRAMING KIT IS USED, IT MAY BE iNSTAUED IN DiRECT CONTACT WITH INSULATED

CEILING. IF A NON il$. TYPE ~ME-fN-KfT IS USEQ DO N~ iNWAU INSULATION WITHIN 3

INCHESOFFfXTURE

SIDE OR WIRING COMPARTMENT,

NOR ABOVE FIXTURE IN SUCH A MANNER TO ENTRAP HSAT.

LONG LEG

1. FRAME-fN (Fig. A)

See Frame-In-Kit Instruction Sheets for installation

SHORT LEG

procedure.

SPRING

2. ROTATE ROTO.CLIPS (Fig. B)

HOOK

Rotate (4) ROTO CLIPS eo that the short legs extend

.-..,.:. ....

inwardly toward the center opening (Fig, F)

:3;

HOUSING

NOTE The SHORT LEG of the RCf70 CLiP hss NO

-..,,

return on top.

......

3. SCREW-IN MALE ADA~ER (Fig. C)

Insert HOOK

in ear of SPRING on SOCKET CUP and

let HOUSING hang down (Fig. G). Screw SOCKET

EXTENSION (MALE ADAPTER) into SOCKET in

SOCKET CUi?

50CKETcup

HOUSING

4. SNARON SOCK~ CUP (Fig. D)

Disengage HOUSING from SOCKET CUP by pulling

HOOK out of SPRING ear (Fig. H). Insert SOCKET

CUP between slots on MOUNTING BRACKET

making sure SPRINGS snap into slots of MOUNTING

BRACK= (Fig. l).

FIG. H

5. PUSH-UP HOUSING (Fig. E)

Tilt HOUSING and inserf SOCKET CUP into ceiling

opening on opposite side of JUNCTION BOX. Pivot

houeing and push it up into ceiling.

SPRING

SOCKETCUP

MOUNTING

US,

PATENTNO 4,313,154;4,327,403.

BRACKET

FOREIGN PATENTsPENDING

FOR OTHER REFLECTOR TRIMS Eyebell (1162), etc See bsck pS9e

[mg<~[=[~<>[m[l~g? MONTREAL, Q”EBEC, CANADA

@ SEC AU CUS, NEW JERSEy,07094.0508

1s1155

IN!YCALLATION OF ADJUSTABLE ACCENT LIGHT (LOW VOLTAGE TRIM)

R0487

6. Remove lAMPHOLDER RING from within HOUSING

by pulling straight down, and disengaging ths LAMP

SPRINGS which also act se a holding mechanism for

lAMPHOLDER RING.

7. Select voltage (12v.,25-50 Watt, or 5.5v, 25 Watt)

depending on lamp being used? by setting SLIDE

SWITCH (Fig. J). Insert screwdriver into slot and slide

switch if not already set according to lamp being

used (See Fig. K).

swHG-

LAMP HOLDER -

SUPPORT

LAMP >

CONNECTOR

HOUSING

8. Install proper wattage PAR36 LAMP into IAMP

CONNECTOR, making certain the LAMP is seated all

the way into the IAMP CONNECTOR.

LAMP=------

9. Insert LAMP into LAMPHOLDER RINGS so that face

of LAMP is seated, and extended through hole in the

LAMPHOLDER RING, and put the lamp and ring

back into the LAMPHOLDER SUPPORT so that the

LAMP SPRINGS now support all.

LAMP HOLDER ~

RING

ti~.

FIG. J

\H “\-

/“

. ...

...’

FIG. K

m4srALumor4 OF

EVEBALL (mw VOLTAGE TRIM)

6. Remove APERTURE TRIM from within EYEBALL by

pullin straight down, and disengaging from

SUPP?)RT SPRINGS (Fig. L).

7. Select voltage (12v., 25-50 Watt, or 5.5v, 25 Watt)

depending on lamp being used! by eetting SLIDE

SWITCH (Fig. L). Insert screwdrwer into slot and slide

switch if not alreedy set according to lamp being

used (See Fig. K).

6. Install proper wattage PAR36 LAMP into LAMP

CONNECTOR, meidng certain the LAMP ia seated all

the way into the IAMP CONNECTOR (Fig, L).

9. Insert LAMP into LAMP SPRING.

10, Insert APERTURE TRIM, and LAMP into EYESALL

until groovee on APERTURE TRIM engage into

SUPPORT SPRINGS [FiO. L).

NOTE LOW VOLTAGE &i+lJRE6 should be

dimmed only with speclel dimmers Mended for

that purpose. Use Ughtoller Preolslon LV, Eoeniet,

or Lytemcds, or equlvelerrt products

~others or

vsrieble eutc-transformers or eleotrcn c dimmers

intended for uee with low voltege flsturss.

NOTE law voltege flstures may produce sudible

sound when used with externel dimme~ which mey

be objectlonsl In acoustically critlcsl srea%

SLID

FIG. L

WARNING USE ONLY REFLECIOR TRIMS PROVIDED SV LIGHTDLIER INC. USE OF ~HER MANUFACTURERS

REFLECIUR TRIMS VOIDS THE UNDERWRITERS IABOFIA30RIES L16TING AND COULD CONSIWIJTE A FIRE

HAZARD.

Lightolier IS:1155 User manual

Brand: Lightolier

Model: IS:1155

Type: User manual

The Lightolier IS:1155 is a versatile and easy-to-install lighting fixture that can be used in a variety of different applications. It is perfect for use in homes, offices, and retail stores.

Download PDF

report

Lightolier IS:1155 User manual

Lightolier IS:1155 User manual

Related papers

Other documents