Greenheck Fan DH100ACDCLP User manual

Greenheck Fan
Brand
Greenheck Fan
Model
DH100ACDCLP
Type
User manual
Purpose/Application
National and local safety standards and codes recognize
the ability of air duct systems to transfer smoke, toxic
gases, and flame from area to area. Sometimes smoke can
be of such quantity as to be a serious hazard to life safety
unless blowers are shut down and dampers are actuated.
The primary purpose of duct smoke detection is to prevent
injury, panic, and property damage by reducing the spread
(recirculation) of smoke. The detector samples air currents
passing through a duct and gives dependable performance
for management of smoke and combination fire smoke
dampers. Duct smoke detection can also serve to protect the
air conditioning system itself from fire and smoke damage.
There are several important documents that provide guidance
concerning the performance, application and installation of
duct detectors:
1) NFPA Standard 90A, Installation of Air Conditioning
and Ventilating Systems
2) NFPA Standard 92A, Recommended Practice for
Smoke Control Systems
3) NFPA Standard 72, National Fire Alarm Code
4) NFPA Standard 101, Life Safety Code
5) UL Standard 268A, Standard for Smoke Detectors for
Duct Applications
6) ASHRAE Handbook and Product Directory, “Fire and
Smoke Control”
7) System Sensor, Guide for Proper Use of Smoke
Detectors in Duct Applications.
Duct detectors are:
NOT a substitute for an open area smoke detector.
NOT a substitute for early warning detection, and
NOT a replacement for a building’s regular fire detection
system.
Availability
For use with all FSD, SSFSD, SMD, SSSMD, and CFSD
models. Not available on SMDR models.
Listings
UL 268A
Configuration
Maximum wall thickness: 6 in. (152mm) on FSD & SSFSD
applications
(Consult factory for walls greater
than 6 in. [152mm])
Actuator Location: Must be right hand drive
Must be externally mounted
Detector Location: Mounts opposite actuator side
Must be external
Sampling tubes longer than three feet must be supported
on each end. Holes in duct smoke detector sampling tubes
must face into the airflow.
Specifications
Type: Photoelectric
Air duct velocity: 100 to 4000 fpm (.5 m/s to
20.3 m/s)
Operating temperature range: 32°F to 131°F (0°C to 55°C)
Operating humidity range: 10% to 93% R.H.
Operation Voltage: 24 VAC/DC or
120/240 VAC
Features
• Texturedcoverforconvenientvisualinspection.
• Thedetectorprovidesatroublesignalintheeventthatthe
front cover is removed.
• Integralfiltersystemincludedtoreducedustandresidue
effects on detector and housing, thereby reducing
maintenance and servicing.
• Terminalconnectionsareofthestripandclampmethod
suitable for 12-18 AWG wiring.
• Outsidemountingtabsforeasyconnectiontosleeveor
ductwork (when detector ships loose).
DUCT SMOKE DETECTOR
DH100ACDCLP
RefertoGreenheckInstallationSupplement:Part#463813IOM-SmokeDetectorSupplement
ORDERING OPTIONSSLEEVE LENGTH
Sleeve Length
Height less than 25 in. (635mm): 24 in. (610mm) sleeve (15 in. [381mm]‘A’ dimension)
(detector mounted parallel to sleeve)
Height greater than or equal to 25 in. (635mm): 21 in. (533mm) sleeve (11 in. [279mm] ‘A’ dimension)
(detector mounted perpendicular to sleeve)
Ordering Options
Factory Mounted
Smoke detector will be wired to a 4 in. x 4 in.
(102mm x 102mm) handi-box. The closure device
(if RRL or TOR) will also be wired to the handi-box.
Dampers provided with the smoke detector option
will include single point wiring as standard (includes
RRL,OCI,TOR,detectors,andmultipleactuators).
Shipped Loose
Shipped loose smoke detector will only include the
detector itself (no mounting hardware or bracket
seals). The duct size will have to be specified in
order to allocate the appropriate length sampling
tube. Adhere to all national and local codes.
Figure 3: Smoke detector mounting orientation for dampers
equal to or greater than 25 inches (635mm) in
height.
Figure 2: Smoke detector mounting orientation for dampers
less than 25 inches (635mm) in height.
%VDU#SFBLBXBZ$POOFDUJPO
CZPUIFST

cJOY
cJO
HBNJOJNVN
SFUBJOJOHBOHMF

cJOY
cJO
HBNJOJNVN
SFUBJOJOHBOHMF
)FJHIUMFTTUIBO
JODIFT
"DDFTTPSZ0$*33-503
NPVOUFEFYUFSOBMMZPOSJHIU
IBOETJEFPGEBNQFS
JOA"EJNFOTJPO JOXBMM
NBYJNVN
JOTMFFWFMFOHUI
/PUF "MMBDUVBUPSTXJMMCF
FYUFS OBMMZNPVOUFEPOUIF
SJHIUIBOETJEFPGEBNQFS
4NPLFEFUFDUPS
NPVOUFEFYUFSOBMMZ
POMFGUIBOETJEFPG
EBNQFS
JONJOJNVNUP
BMMPXGPSSFUBJOJOH
BOHMFBOEEVDU
CSFBLBXBZ
DPOOFDUJPO
%VDU#SFBLBXBZ
$POOFDUJPOCZPUIFST

cJOY
cJO
HBNJOJNVN
SFUBJOJOHBOHMF

cJOY
cJO
HBNJOJNVN
SFUBJOJOHBOHMF
4NPLFEFUFDUPS
NPVOUFE
FYUFSOBMMZPO
MFGUIBOETJEFPG
EBNQFS
)FJHIU
FRVBMUP
PSHSFBUFS
UIBO
JODIFT
"DDFTTPSZ0$*33-503
NPVOUFEFYUFSOBMMZPOSJHIU
IBOETJEFPGEBNQFS
JOA"EJNFOTJPO JOXBMM
NBYJNVN
JOTMFFWFMFOHUI
/PUF "MMBDUVBUPSTXJMMCF
FYUFSOBMMZNPVOUFEPOUIF
SJHIUIBOETJEFPGEBNQFS
JONJOJNVNUP
BMMPXGPSSFUBJOJOH
BOHMFBOEEVDU
CSFBLBXBZ
DPOOFDUJPO
Figure 1: Label applied to
dampers with
factory mounted
duct smoke
detectors.
IMPORTANT!
Dampers ordered with shipped loose smoke detectors
will have the standard sleeve length, not a longer sleeve
toaccommodatethesmokedetectorinstallation.If
smoke detectors are intended to be field mounted on
the damper sleeve, the damper sleeve length and ‘A’
dimension will need to be manually changed to the
requirements indicated under ‘Sleeve Length’.
4NPLFEFUFDUPSSFRVJS FTGQNNJOJNVN
BJSWFMPDJUZJOEVDU'PSEBNQFSBDUJWBUJPO
SFRVJSFNFOUTXIFOTZTUFNWFMPDJUZJTMFTT
UIBOGQNUIFMPDBMBVUIPSJUZIBWJOH
KVSJTEJDUJPOTIPVMECFDPOTVMUFE
3FGFSUPTNPLFEFUFDUPSJOTUBMMBUJPO
JOTUSVDUJPOTBOE(SFFOIFDL*0.4NPLF
%FUFDUPS4VQQMFNFOU'4GPSEBNQFSTXJUI
GBDUPSZNPVOUFEEVDUTNPLFEFUFDUPST

Electrical Ratings
Power Supply Voltage: 20-29 VDC 24 VAC 50-60 Hz 120 VAC 50-60 Hz 220/240 VAC 50-60 Hz
InputCapacitance: 270µFmax. 270µFmax. N/A N/A
Reset Voltage: 3.0 VDC min. 2.0 VAC min. 10 VAC min. 20 VAC min.
Reset Time: 0.6 sec. max. 0.6 sec. max. 0.6 sec. max. 0.6 sec. max.
Power Up Time: 34 sec. max. 34 sec. max. 34 sec. max. 34 sec. max.
Alarm Response Time: 2-17 sec. 2-17 sec. 2-17 sec. 2-17 sec.
Sensitivity Test: See detector label See detector label See detector label See detector label
Current Requirements
Max. Standby Current: 15 mA 35 mA RMS 25 mA RMS* 15 mA RMS*
Max. Alarm Current: 70 mA 125 mA RMS 35 mA RMS* 25 mA RMS*
Contact Ratings
AlarmInitiationContacts(SPST): 2.0A@30VAC/DC(0.6powerfactor)
AlarmAuxiliaryContacts(DPDT): 10A@30VDC
10A@250VDC
Note: Alarm auxiliary contacts must switch 100 mA minimum at 5 VDC. Alarm auxiliary contacts shall not be connected
to initiating circuits of control panels. Use the alarm initiation contact for this purpose.
TroubleContacts(SPDT): 2.0A@30VDC(resistive)
ELECTRICAL RATINGSSPACE ENVELOPES
T ypical Actuator
(ML series shown; other
actuators available)
Single Point W iring (Standar d)
Smoke detector , actuator , and al l
cont ro l options ar e pr ewir ed to
junction box at the factor y.
6
3
⁄ 4 in.
3 in.
Typical Actuator
(other actuators available)
Single Point Wiring
(Standard): Smoke
detector, actuator, and
all control optiong are
prewired to junction box
at the factory.
15 in.
(381mm)
2 3/4 in.
(70mm)
Dampers Less Than 25 Inches (635mm) In Height
Dampers Equal To Or Greater Than 25 Inches (635mm) In Height
OPTIONAL
SECOND MOTOR
L2
MOTOR
WHITE
MOTOR
L1
BLUE
BLACK
DH100ACDCLP DUCT DETECTOR
115 VAC
RED
15
5
1211
2
1
1413
34
18
8
16 17
67
19 20
910C
A
B
BLACK
WHITE
WHITE
MOTOR
BLACK
OPTIONAL
THIRD MOTOR
DH100ACDCLP DUCT DETECTOR
BLUE
RED
WHITE
24 VAC/VDC
WHITE
1211 1413
1
2345
15 1816 17 19 20
867 910C
A
B
1. CONDUIT RUNS WHICH EXCEED 72" MUST HAVE GREEN GROUND WIRE.
2. FLEX CONDUIT MUST BE SECURED WITH A CONDUIT CLAMP (458296) WITHIN 12" OF CONDUIT TERMINATION AT THE HANDI-BOX OR ACTUATOR. CONDUIT RUNS MUST ALSO BE
SECURED ALONG SLEEVE AT A MAXIMUM OF 24" ON CENTER.
CB
A
10
20
8976
1816 17 19
423
1412 1311
1
15
5
WHITE
RED
BLUE
220/240 VAC
DH100ACDCLP DUCT DETECTOR
Fusible Link
DUCT SMOKE DETECTORWIRING DIAGRAMS
OPTIONAL
SECOND MOTOR
L2
MOTOR
WHITE
MOTOR
L1
BLUE
BLACK
DH100ACDCLP DUCT DETECTOR
115 VAC
RED
OCI
15
5
1211
2
1
1413
34
18
8
16 17
67
19 20
910C
A
B
YELLOW
YELLOW
YELLOW
YELLOW
SWITCH #1
SWITCH #2
BLACK
WHITE
WHITE
MOTOR
BLACK
OPTIONAL
THIRD MOTOR
DH100ACDCLP DUCT DETECTOR
BLUE
RED
WHITE
24 VAC/VDC
WHITE
1211 1413
1
2345
15 1816 17 19 20
867 910C
A
B
1. CONDUIT RUNS WHICH EXCEED 72" MUST HAVE GREEN GROUND WIRE.
2. FLEX CONDUIT MUST BE SECURED WITH A CONDUIT CLAMP (458296) WITHIN 12" OF CONDUIT TERMINATION AT THE HANDI-BOX OR ACTUATOR. CONDUIT RUNS MUST ALSO BE
SECURED ALONG SLEEVE AT A MAXIMUM OF 24" ON CENTER.
THE OCI WIRES MUST BE CHECKED TO VERIFY WHICH SET INDICATES THE CLOSED POSITION OF
DAMPER. THIS SET OF WIRES SHOULD THEN BE LABELED WITH A BLUE WIRE MARKER (382169).
DH100ACDCLP DUCT DETECTOR
220/240 VAC
BLUE
RED
WHITE
20
1311 12
15
14
1816 17 19
103
1
2548769 B
A
C
OCI
OPTIONAL
SECOND MOTOR
L2
MOTOR
WHITE
MOTOR
L1
BLACK
ORANGE
BLUE
BLACK
DH100ACDCLP DUCT DETECTOR
115 VAC
RED
RRL
15
5
1211
2
1
1413
34
18
8
16 17
67
19 20
910C
A
B
BLACK
WHITE
WHITE
MOTOR
BLACK
OPTIONAL
THIRD MOTOR
DH100ACDCLP DUCT DETECTOR
BLUE
RED
WHITE
24 VAC/VDC
WHITE
1211 1413
1
2345
15 1816 17 19 20
867 910C
A
B
1. CONDUIT RUNS WHICH EXCEED 72" MUST HAVE GREEN GROUND WIRE.
2. FLEX CONDUIT MUST BE SECURED WITH A CONDUIT CLAMP (458296) WITHIN 12" OF CONDUIT TERMINATION AT THE HANDI-BOX OR ACTUATOR. CONDUIT RUNS MUST ALSO BE
SECURED ALONG SLEEVE AT A MAXIMUM OF 24" ON CENTER.
A
BC109864352
1
7
WHITE
191716 18
14
15
1211 13
20
RED
BLUE
DH100ACDCLP DUCT DETECTOR
220/240 VAC
RRL
RRL/OCI
OPTIONAL
SECOND MOTOR
L2
MOTOR
WHITE
MOTOR
L1
BLACK
ORANGE
BLUE
BLACK
DH100ACDCLP DUCT DETECTOR
115 VAC
RED
RRL
15
5
1211
2
1
1413
34
18
8
16 17
67
19 20
910C
A
B
YELLOW
YELLOW
YELLOW
YELLOW
SWITCH #1
SWITCH #2
BLACK
WHITE
WHITE
MOTOR
BLACK
OPTIONAL
THIRD MOTOR
DH100ACDCLP DUCT DETECTOR
BLUE
RED
WHITE
24 VAC/VDC
WHITE
1211 1413
1
2345
15 1816 17 19 20
867 910C
A
B
1. CONDUIT RUNS WHICH EXCEED 72" MUST HAVE GREEN GROUND WIRE.
2. FLEX CONDUIT MUST BE SECURED WITH A CONDUIT CLAMP (458296) WITHIN 12" OF CONDUIT TERMINATION AT THE HANDI-BOX OR ACTUATOR. CONDUIT RUNS MUST ALSO BE
SECURED ALONG SLEEVE AT A MAXIMUM OF 24" ON CENTER.
THE OCI WIRES MUST BE CHECKED TO VERIFY WHICH SET INDICATES THE CLOSED POSITION OF
DAMPER. THIS SET OF WIRES SHOULD THEN BE LABELED WITH A BLUE WIRE MARKER (382169).
DH100ACDCLP DUCT DETECTOR
220/240 VAC
BLUE
RED
WHITE
20
1311 12
15
14
1816 17 19
103
1
2548769 B
A
C
DUCT SMOKE DETECTORWIRING DIAGRAMS
DUCT SMOKE DETECTORWIRING DIAGRAMS
OPTIONAL
SECOND MOTOR
(PRIMARY)
L2
MOTOR
WHITE
MOTOR
SWITCHING DEVICE
(BY OTHERS)
L1
(OVERRIDE)
BROWN
BLACK
ORANGE
BLUE
BLACK
DH100ACDCLP DUCT DETECTOR
115 VAC
RED
TOR
15
5
1211
2
1
1413
34
18
8
16 17
67
19 20
910C
A
B
YELLOW
YELLOW
YELLOW
YELLOW
SWITCH #1
SWITCH #2
BLACK
WHITE
WHITE
MOTOR
BLACK
OPTIONAL
THIRD MOTOR
DH100ACDCLP DUCT DETECTOR
BLUE
RED
WHITE
24 VAC/VDC
WHITE
1211 1413
1
2345
15 1816 17 19 20
867 910C
A
B
1. CONDUIT RUNS WHICH EXCEED 72" MUST HAVE GREEN GROUND WIRE.
2. FLEX CONDUIT MUST BE SECURED WITH A CONDUIT CLAMP (458296) WITHIN 12" OF CONDUIT TERMINATION AT THE HANDI-BOX OR ACTUATOR. CONDUIT RUNS MUST ALSO BE
SECURED ALONG SLEEVE AT A MAXIMUM OF 24" ON CENTER.
THE OCI WIRES MUST BE CHECKED TO VERIFY WHICH SET INDICATES THE CLOSED POSITION OF
DAMPER. THIS SET OF WIRES SHOULD THEN BE LABELED WITH A BLUE WIRE MARKER (382169).
14
220/240 VAC
BLUE
1211 13
2
1
43
DH100ACDCLP DUCT DETECTOR
RED
WHITE
19171615 18 20
9657810B
A
C
TOR
OCIw/EPSwitch
L2
WHITE
L1
BLACK
ORANGE
BLUE
BLACK
DH100ACDCLP DUCT DETECTOR
115 VAC
RED
RRL
15
5
1211
2
1
1413
34
18
8
16 17
67
19 20
910C
A
B
YELLOW
YELLOW
YELLOW
YELLOW
SWITCH #1
SWITCH #2
DH100ACDCLP DUCT DETECTOR
BLUE
RED
WHITE
24 VAC/VDC
WHITE
1211 1413
1
2345
15 1816 17 19 20
867 910C
A
B
REDRED
E/P SWITCH
OPTIONAL
THIRD E/P SWITCH
OPTIONAL
SECOND E/P SWITCH
RED
RED
WHITE
E/P SWITCH
RED
WHITE
E/P SWITCH
RED
BLACK
BLACK
1. CONDUIT RUNS WHICH EXCEED 72" MUST HAVE GREEN GROUND WIRE.
2. FLEX CONDUIT MUST BE SECURED WITH A CONDUIT CLAMP (458296) WITHIN 12" OF CONDUIT TERMINATION AT THE HANDI-BOX OR ACTUATOR. CONDUIT RUNS MUST ALSO BE
SECURED ALONG SLEEVE AT A MAXIMUM OF 24" ON CENTER.
THE OCI WIRES MUST BE CHECKED TO VERIFY WHICH SET INDICATES THE CLOSED POSITION OF
DAMPER. THIS SET OF WIRES SHOULD THEN BE LABELED WITH A BLUE WIRE MARKER (382169).
BC
A
910674523
1
8
19 2017
14
15 16
12 1311
18
WHITE
RED
BLUE
220/240 VAC
DH100ACDCLP DUCT DETECTOR
RRL/OCIW/EPSwitch
L2
WHITE
L1
BLACK
ORANGE
BLUE
BLACK
DH100ACDCLP DUCT DETECTOR
115 VAC
RED
RRL
15
5
1211
2
1
1413
34
18
8
16 17
67
19 20
910C
A
B
DH100ACDCLP DUCT DETECTOR
BLUE
RED
WHITE
24 VAC/VDC
WHITE
1211 1413
1
2345
15 1816 17 19 20
867 910C
A
B
REDRED
E/P SWITCH
OPTIONAL
THIRD E/P SWITCH
OPTIONAL
SECOND E/P SWITCH
RED
RED
WHITE
E/P SWITCH
RED
WHITE
E/P SWITCH
RED
BLACK
BLACK
1. CONDUIT RUNS WHICH EXCEED 72" MUST HAVE GREEN GROUND WIRE.
2. FLEX CONDUIT MUST BE SECURED WITH A CONDUIT CLAMP (458296) WITHIN 12" OF CONDUIT TERMINATION AT THE HANDI-BOX OR ACTUATOR. CONDUIT RUNS MUST ALSO BE
SECURED ALONG SLEEVE AT A MAXIMUM OF 24" ON CENTER.
BC
A
910674523
1
8
19 2017
14
15 16
12 1311
18
WHITE
RED
BLUE
220/240 VAC
DH100ACDCLP DUCT DETECTOR
RRL W/ EP Switch
DUCT SMOKE DETECTORWIRING DIAGRAMS
DUCT SMOKE DETECTORWIRING DIAGRAMS
(PRIMARY)
L2
WHITE
SWITCHING DEVICE
(BY OTHERS)
L1
(OVERRIDE)
BROWN
BLACK
ORANGE
BLUE
BLACK
DH100ACDCLP DUCT DETECTOR
115 VAC
RED
TOR
15
5
1211
2
1
1413
34
18
8
16 17
67
19 20
910C
A
B
YELLOW
YELLOW
YELLOW
YELLOW
SWITCH #1
SWITCH #2
DH100ACDCLP DUCT DETECTOR
BLUE
RED
WHITE
24 VAC/VDC
WHITE
1211 1413
1
2345
15 1816 17 19 20
867 910C
A
B
REDRED
E/P SWITCH
OPTIONAL
THIRD E/P SWITCH
OPTIONAL
SECOND E/P SWITCH
RED
RED
WHITE
E/P SWITCH
RED
WHITE
E/P SWITCH
RED
BLACK
BLACK
1. CONDUIT RUNS WHICH EXCEED 72" MUST HAVE GREEN GROUND WIRE.
2. FLEX CONDUIT MUST BE SECURED WITH A CONDUIT CLAMP (458296) WITHIN 12" OF CONDUIT TERMINATION AT THE HANDI-BOX OR ACTUATOR. CONDUIT RUNS MUST ALSO BE
SECURED ALONG SLEEVE AT A MAXIMUM OF 24" ON CENTER.
THE OCI WIRES MUST BE CHECKED TO VERIFY WHICH SET INDICATES THE CLOSED POSITION OF
DAMPER. THIS SET OF WIRES SHOULD THEN BE LABELED WITH A BLUE WIRE MARKER (382169).
C
A
910B785634
1
2
2017 1815 16
13 1411 12
19
WHITE
RED
BLUE
220/240 VAC
DH100ACDCLP DUCT DETECTOR
TOR w/ EP Switch
Copyright © 2008 Greenheck Fan Corporation
DH100 Smoke Detector Rev. 6 May 2008
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Greenheck Fan DH100ACDCLP User manual

Greenheck Fan
Brand
Greenheck Fan
Model
DH100ACDCLP
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents