Page is loading ...
Access and Congure Your BEC Device
The default IP of modem is 192.168.1.254 with subnet 255.255.255.0. Make sure the attached PC to this router
is in the same subnet and has an IP address in the range between 192.168.1.1 ~ 192.168.1.253.
Open a web browser and type http://192.168.1.254 in the URL address bar.
Quick Setup Your Router
Use the Quick Start for fast connection setup.
Setup a new password for “admin” account for
device management. The default password is
“admin”. Click Continue to go on to the next step.
*The password may vary by different Internet Service Providers.
http://192.168.1.254
URL Address bar: type
http://192.168.1.254
The login prompt will appear. Input the default username and password.
*This username / password may vary by different Internet Service Providers.
Step 1: Change administration password
Enable and select your Time Zone then click
Continue to go on to the next step.
Step 2: Time Zone configuration
Select the appropriate WAN protocol then fill out the information provided by your ISP in all relevant parameters.
Step 3: WAN / Internet Connection Setup
Click “Next” to save and complete the Quick Setup.
You should now be able to access to the Internet.
Step 4: Save Confirmation Settings
New Password: assign a new,
unique password
Confirm Password: re-enter the
new password again
Next Step: click Next
Time Zone: select your time zone
Next Step: click Next
WAN Interface: select 4G/LTE
Next Step: click Next
Input all relevant parameters from your provider.
Contact with your provider for further support.
Next Step:
click Next to continue
Protocol: select one of them
-Dynamic IP Address (Obtain an IP address
automatically)
-Static IP Address (Manually assign an IP)
-PPPoE
-Bridge Mode
Next Step: click Next to continue
(4G/LTE) If select 4G/LTE to connect to the internet
(WAN) If select Ethernet WAN to connect to the internet
Congure Your BEC Router – Verizon & Sprint User Only
Step 1: Login to the BEC router web menu, BEC default IP is http://192.168.1.254
Step 2: Click Configuration > Interface Setup > Internet to make sure you:
1. (Verizon Users): Ensure the APN is set to vzwinternet or another APN provided by VZW. Click Save to apply
settings.
2. Verify the Carrier Switch selection is set for your carrier. If not, click the Carrier Switch link and select the Carrier from
the drop-down selection.
When finish, click Save & Reboot to apply the setting. Wait a few minutes.
http://192.168.1.254
URL Address bar: type
http://192.168.1.254
When the login prompt appear. Input the default username and password, admin and admin.
*This username / password may vary by different Internet Service Providers.
Step 3: After the Save & Reboot completed, go back to Configuration > Interface Setup > Internet,
verify the Carrier Switch is set to the selected carrier.
Step 4: If all is set correctly and the SIM is activated by Sprint or VZW, the device should gain Internet access.
Sprint User
Verizon User
NOTE: Auto Carrier (optional) will automatically detect the carrier.
MX-200(e)
MX-200A(e)
MX-230 M1
Quick Install Guide
www.bectechnologies.net
www.bectechnologies.net
THIS SPACE INTENTIONALLY LEFT BLANK
M
2
M
3301 Matrix Drive Ste 200
Richardson, TX 75082 USA
TEL : +1-972-422-0877
FAX : +1-972-422-0886
E-mail : [email protected]
Congure Your BEC Router – AT&T, T-Mobile and Other Carriers
Step 1: Login to the BEC router web menu, BEC default IP is http://192.168.1.254
Step 2: Click Configuration > Interface Setup > Internet to make sure you:
1. (AT&T and T-Mobile Users): No action is required. Make sure the APN field is in default setting, left in blank.
2. (Other Carriers): Contact your carrier to verify the correct APN setting.
When finish, click Save & Reboot to apply the setting. Wait a few minutes.
Step 3: If all is set correctly and the SIM is activated. Your BEC device should gain Internet access.
http://192.168.1.254
URL Address bar: type
http://192.168.1.254
When the login prompt appear. Input the default username and password, admin and admin.
*This username / password may vary by different Internet Service Providers.
SETTING UP THE ROUTER
Quick Install Guide
WHAT’S IN THE BOX
3G/4G Antennas
Active GPS Antenna
(Optional Accessories)
1 x BEC MX-200(e)/200A(e)/230 M1
1 x DIN Rail Mounting Kit
1 x This Quick Install Guide
1 x Ethernet (RJ-45) Cable
1 x DC Power Adapter, 12V 1.2A
1 x Power Terminal Block 2-Pin 3.5mm
1 x Power Converter with 2-Pin Terminal Block
KIT CONTAINS: DIN Rail Clip and Six (6) Clip Mounting Screws
The DIN Rail mounting kit is designed to securely attach and clip the MX-200(e)/200A(e)/230 M1 onto a TS35 or
standard 35mm top hat (EN 500022/BS 5584) DIN rail in the horizontal position.
Two (2) mounting locations to mount the DIN rail clip on the surface of MX-200(e)/200A(e)/230 M1, back or rear side.
Please follow the steps to complete DIN rail mounting installation.
DIN RAIL MOUNTING KIT
ATTACHING TO A DIN RAIL
REMOVING FROM A DIN RAIL
1. MX-200(e)/200A(e)/230 M1
2. Mounting Bracket
3. Mounting Screws
I
Gb ETH
1 2
SERIAL
3
1
2
3
II
Gb ETH
1 2
SERIAL
Gb ETH
1 2
SERIAL
DIN Rail
1
Top
Bottom
Gb ETH
1 2
SERIAL
Gb ETH
1 2
SERIAL
3
I
Gb ETH
1 2
SERIAL
Gb ETH
1 2
SERIAL
1
Gb ETH
1 2
SERIAL
Gb ETH
1 2
SERIAL
Bottom
2
Gb ETH
1 2
SERIAL
Gb ETH
1 2
SERIAL
Top
3
4
REMOVING FROM A DIN RAIL
MX-200
MXConnect
Gb ETH
1 2
SERIAL
I
Install clip in either vertical or horizontal position.
2
Gb ETH
1 2
SERIAL
Clip and secure the MX-200(e)/200A(e)/230 M1 onto a
DIN rail.
1. Hook the top of the clip onto the top edge of the DIN
rail. Make sure the clip is firmly against the rail.
2. Push down the bottom of the MX-200(e)/200A(e)/
230 M1 to snap it onto the lower edge of the DIN rail.
3. The MX-200(e)/200A(e)/230 M1 is now mounted on
the DIN
v1.1
Attach and fasten the DIN rail clip (known as clip) to the
back or rear side of the MX-200(e)/200A(e)/230 M1
using two (2) clip mounting screws included in this
mounting kit.
Remove MX-200(e)/200A(e)/230 M1 from a DIN rail.
1-2. Push down the MX-200(e)/200A(e) to free the
bottom of the clip from the DIN rail.
3-4. Unhook the top of the clip and pull the
MX-200(e)/200A(e)/230 M1 away from the DIN
rail.
Model: MX-200(e)/200A(e)/230 M1
M
2
M
Gb ETH
1 2
SERIAL
Gb ETH
1 2
SERIAL
2
Connect the Serial (RS-232)
4 Connect to Power Source
1 Insert the SIM Card
VCC(on the left) - Red Wire
GND(on the right) - Black Wire
Power
POWER
INTERNETWAN
Gb ETH
12
SIM
SIM
POWERINTERNETWAN
Gb ETH
12 SIM
SIM
POWERRESET
WAN
AUX
WAN
MAIN
GPS
POWERRESET
GNDVCC
POWERRESET
WAN
AUX
WAN
MAIN
GPS
3
Attach the LTE & GPS Antennas
5
Access to the MX-200(e)/200A(e)/ 230 M1
Access to the MX-200(e)/200A(e)/230 M1 Web interface by
entering http://192.168.1.254 in the address bar of the web
browser.
Default Login: Username (admin) and Password (admin or
a unique12-digit password can be found on the device label).
The Quick Start Wizard provides key steps to connect the
MX-200(e)/200A(e)/230 M1 to the Internet.
Screw the male SMA 3G/4G-LTE and/or GPS antennas tight
to the female connectors.
Connect to the MAIN port, the primary cellular antenna port
to transmit and receive signal, if decide to use one antenna.
Do not over-torque the antenna on the connector.
Use External Power Supply
Use the DC Power Adapter
Note: Power o the MX-200(e)/200A(e)/230 M1 before inserting or
removing the SIM
Remove the SIM cover
then insert the SIM card(s)
(2FF) with the mental
contacts (gold plate)
facing down to the SIM
slot(s) then push it all the
way in until you hear the clicking sound.
Replace the metal SIM cover after inserting the SIMs.
Use a RS-232 (DB-9) male serial adapter to connect with
industrial equipment – including PLC, SCADA, Sensor,
Meters, and Motor.
Attach the power terminal block (TB) to 200(e)/200A(e)/
230 M1 and connect wire leads from a power supply to the
terminal block (TB) plug.
RED Wire (Left Connector): VCC/V+. Connect to the positive
supply voltage. Input voltage range is from 9V to 56V.
BLACK Wire (Right Connector): Ground (GND)/V-. Connect
to the negative supply voltage.
Attach the power converter with 2-pin terminal block to the
MX-200(e)/200A(e)/230 M1 and plug in the supplied power
adapter, 12VDC 1.2A.
POWERRESET
WAN
AUX
WAN
MAIN
GPS
Gb ETH
1 2
SERIAL
DEVICE OVERVIEW & LEDS
GPS Antenna
SMA Female Connector
Reset
Power
(V+)
(Input power 9-56V DC range)
Gigabit RJ-45
Ethernet LAN Port
Gigabit RJ-45
Ethernet LAN/WAN Port
RS-232 Serial
(DB-9)
3G/4G-LTE
(Auxiliary Antenna)
SMA Female Connector
3G/4G-LTE
(Main Antenna)
SMA Female Connector
Ground
(V-)
POWERINTERNETWAN
Gb ETH
12 SIM
2
Ethernet
LAN
1
3
4
LTE Signal
Strength
Internet
Power SIM Slot
INTERNET
Green: IP traffic via WAN
Red: WAN IP request failed
Off: No WAN Connection or in Bridge Mode
3
2
WAN (Cellular Signal Strength Indicator)
Green: RSSI > -69 dBm. Excellent signal
Green / Fast Flashing: -69 > RSSI > -81dBm. Good signal
Red / Fast Flashing: -81 > RSSI > -99dBm. Fair signal
Red / Slow Flashing: -99dBm > RSSI. Poor signal
Red: No signal and the 4G LTE module is in service
Off: No LTE module or LTE failure
1
GIGABIT ETHERNET (Gb ETH) (LAN #1 & #2)
Green: Transmission speed is at Gigabit speed (1000Mbps)
Orange: Transmission speed is at 10/100Mbps
Blinking: Data being transmitted/received
POWER
4
Green: System ready
Red: Boot failure
5
SIM Card Slot
5
Insert mini SIM card (2FF) with the gold contact facing down.
Push mini SIM card (2FF) inwards to eject it
* Power off the MXConnect router before inserting or removing the SIM card
PRODUCT SUPPORT AND CONTACT INFORMATION
Most problems can be solved by referring to the Troubleshooting section in the User Manual.
If you have other inquiries or need further technical support, please contact with your Internet Service Provider or visit us at
www.bectechnologies.net
FCC Caution:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this devise may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
(No Use for MX-230 M1)
POWERRESET
WAN
AUX
WAN
MAIN
GPS
POWERRESET
WAN
AUX
WAN
MAIN
GPS
POWERRESET
WAN
AUX
WAN
MAIN
GPS
POWERRESET
WAN
AUX
WAN
MAIN
GPS
Note: GPS and 3G/4G-LTE antenna(s) sold separately
/
