Teleco Flatsat Komfort User manual

Brand: Teleco

Model: Flatsat Komfort

Type: User manual

Teleco Flatsat Komfort is an advanced satellite TV reception system that offers a range of features for easy and convenient TV viewing on the go. With its compact and lightweight design, it's ideal for caravans, motorhomes, and boats. Enjoy a variety of channels and crystal-clear reception wherever your travels take you.

Installation manual

Flat Sat Komfort

TABLE OF CONTENTS Page

Information ...............................................................................................................................................1

List of accessories........................................................................................................................................2

Important notice..........................................................................................................................................3

Assembly instructions..................................................................................................................................5

Installation with cables coming out sideways............................................................................................6

Installation with cables through the centre of the base plate....................................................................8

Flat Sat Komfort – Front view....................................................................................................................9

Flat Sat Komfort – Rear view....................................................................................................................9

Flat Sat Komfort Kits...............................................................................................................................10

How to identify your Flat Sat Komfort Kit.................................................................................................10

Complete Kit with Black Box, Sat Decoder and TV.................................................................................11

Connecting the complete Kit with a Sat FORCE HD CI+ receiver and a 19" Teleco United TV......................12

Connecting the complete Kit with a TivuSat DS510M receiver and a 19" Teleco United TV (Italy only)........13

Connecting the complete Kit with a TNT SD M6000 receiver and a 19" Teleco United TV (France only)...14

Connecting the complete Kit with a TNT HD M5200/M7000 receiver and a

19" Teleco United TV (France only)..........................................................................................................15

Kit with Black Box, Sat Decoder without TV...............................................................................................16

Connecting the Kit with a Sat FORCE HD CI+ receiver .........................................................................17

Connecting the Kit with a TivuSat DS510M receiver (Italy only)..................................................................18

Connecting the Kit with a TNT SD M6000 receiver (France only)...........................................................19

Connecting the Kit with a TNT HD M5200/M7000 receiver (France only)...........................................................20

Configuration without Kit – connection diagram........................................................................................21

LNB rotation for ideal signal reception in extreme areas in Europe........................................................22

Installation tips...........................................................................................................................................23

Technical specifications..............................................................................................................................23

Spare parts tables.....................................................................................................................................24

Kit labels.................................................................................................................................................30

Information

Congratulations on your purchase! Flat Sat Komfort is among the most technologically

advanced products in the field of satellite TV reception. This handbook has been prepared

to provide information on the technical specifications and how to install, use and maintain

your Flat Sat Komfort system:

For additional information, please contact your local dealer or directly the manufacturer:

TELECO s.p.a.

Via E. Majorana 49

48022 LUGO (RA)

Web site: www.telecogroup.com

After-sales service: 899.899.856

TELECO s.p.a. declines all responsibility for any errors contained in this manual. All information

contained herein is up to the date of printing and the above-mentioned revisions. TELECO

s.p.a. reserves the right to make any changes made necessary by the development of its

products.

List of accessories

Flat Sat Komfort is delivered inside a cardboard case that has been specially made to protect

it from knocks and pressure. The following accessories are supplied:

1 External motor-driven unit

2 65-85 cm dish

3 Universal LNB

3 SKEW (OPTIONAL)

4 Black Box

5 MIR remote control expander

6 Motor Connection Cable

7 Antenna/Black Box Connection Lead

8 Power Supply Cable

9 Remote Control

10 Waterproof box to pass leads through

11 Heat-shrinking sheaths

12 Roof attachment plate

13 No. 4 Locknuts M6

14 No. 4 Screws and Locknuts - M6

15 User’s manual and installation manual

16 Jack-Jack lead 0.5 m

16 Jack-Jack lead 2.0 m

Important notice

Flat Sat Komfort is packaged in two separate cartons for transport reasons:

a) the first package contains the driving unit with all the cables, and the Black Box;

b) the second package only contains the dish.

• It is important to check that the dish has not been damaged during transport when

the package is opened. In particular, check the following carefully:

• By resting the dish edge against a flat surface (e.g. the floor or a wall) check that it makes

contact to the surface all around. If it is not so, try and make the edge level, without denting

the dish, or call our After-Sales Service.

• After checking that everything is in order, install the dish on the driving unit as follows:

1) Temporarily connect the Black Box to the Driving unit via the grey motor cable.

2) Connect the Mir remote control expander to the "IR BLACK BOX" connector in the

Black Box.

3) Power the Black Box using a battery.

4) Press the System ON-OFF button on the remote control and wait (about 30 seconds)

for the dish support mast to rise.

5) Once you have reached the desired position, disconnect the power supply cable to

switch off the Flat Sat Komfort.

6) Secure the dish to the mast and screw down the four supplied screws.

7) Turn the unit on again and wait for the antenna to close.

8) Disconnect the Black Box, the battery and install the driving unit on the vehicle.

Recycling: with a view to reducing disposal of waste electrical and electronic

equipment as much as possible, do not throw out this appliance, once it has

reached the end of its life, together with other unsorted municipal waste, but make

use of a recycling centre.

YES NO

Assembly instructions

1) Position the Black Box in an easy accessible, ventilated compartment.

2) On the roof of the vehicle, choose a free area large enough to allow the antenna to

revolve (Fig. 2).

3) Install the connection cables (Grey and White) until you reach the powered OUTSIDE

UNIT installation area.

4) Clean the roof carefully in the area the OUTSIDE UNIT is to be installed in.

5) Remembering that the OUTSIDE UNIT must be fastened as shown on Fig. 3, remove

the BASE PLATE from the outside unit, unscrewing all 4 nuts.

6) Position the base plate as shown on Fig. 4, with the short side towards the driving

direction of the vehicle.

Flat Sat Komfort

650 - 140 cm

Flat Sat Komfort 850

- 160 cm

Driving direction

of the vehicle

When they are present, remove the transparent films from the BASE PLATE (Fig. 5).

7) Clean the lower part of the BASE PLATE carefully, applying a layer of glue on the

whole surface (e.g. SIKAFLEX).

8) Fasten the BASE PLATE to the roof (short side towards the vehicle driving direction),

now fasten the external powered unit to the four stud bolts of the plate, using the four

nuts supplied with the equipment.

Caution: to ensure ideal nut tightening and prevent possible pin breaks, tighten

the nut with a torque wrench set to 8 Newtons/metre

Driving direction

of the vehicle

9) Apply a layer of silicone all around the BASE PLATE in order to make it completely

waterproof (Fig. 5A)

5 5A

Driving direction

of the vehicle

12)Accomodate the cables into a protection raceway up to the point where the cables go

into the vehicle, using the suitable supplied fairlead.

9) Seal the fairlead

carefully so as to

prevent any

infiltration by water

Installation with cables coming out sideways

10) Fasten the OUTSIDE UNIT on the base plate and lead the two cables through any of the 4

existing grooves, according to the position as shown on Fig. 6.

WARNING: When performing this operation, do not draw the two cables forcefully, as this might pull

them out.

Connection with extension

11) Connect the two cables coming from the centre of the OUTSIDE UNIT to the two supplied

extensions, waterproofing the connectors using the two pieces of heat-shrinking tube.

WARNING The Grey and White cables coming

out of the Outside Unit are generally long enough

to allow for connection to the Black Box. If it is

not so, use the extension cables and perform

the following operations:

Installation with cables through the centre of the base plate

WARNING The Grey and White cables coming out of the Outside Unit are generally long

enough to allow for connection to the Black Box. If it is not so, use the extension cables and

perform the following operations:

Connection with extension

13)Connect the Grey and White extension cables, coming from inside the vehicle (Fig. 10)

to the two cables of the outside unit, waterproofing them using two pieces

of HEAT-SHRINKING TUBE (Fig. 11).

WARNING When performing this operation, do not draw the cables coming from the centre

of the outside unit forcefully, as this might pull them out.

14)Install the OUTSIDE UNIT on the base plate, remembering that:

a) The right position is the one shown on (Fig. 13)..

b) Apply an abundant layer of silicone on both the base plate and the bottom of the driving

unit so as to prevent any infiltration by water. Screw down the 4 supplied nuts

by the screws and tighten properly (Fig. 15).

Flat Sat Komfort – Rear Black Box View

1) F type connector – input from LNB converter of the driving unit

2) F type connector – signal output to be connected to any satellite receiver

3) B type USB connector – connection to a PC for updating purpose

4) Connector for connection to the driving unit

5) Diagnostics button (for technical staff only)

6) Connector for power supply input from battery and safety cable

7) 5 A blade fuse

8) SCART connector – TV output

9) SCART connector – Decoder input

10) Jack Connector - Decoder (for Kit configuration only)

11) Jack Connector - TV (for Kit configuration only)

12) Connector for MIR Remote Control Expander

3 4

1) Power-on indication LED

Flat Sat Komfort – Front Black Box View

Flat Sat Komfort Kits

Flat Sat Komfort can be purchased in the following configurations:

• Complete Kit with Black Box, Sat Decoder and TV

• Kit with Black Box and Sat Decoder (without TV)

• Without Kit, with Black Box only (without both TV and Sat Decoder)

How to identify your Flat Sat Komfort Kit

In order to identify the configuration you purchased, make sure that the Kit labels are applied

on the proper Kit-matching devices. The label which is applied on the back of the devices

is as follows:

Example:

Black Box

Decoder Sat

In the complete KIT with Black Box, Sat DECODER and TV there are no. 4 Kit labels, one

on the Black Box, one on the remote control battery compartment, one on the Sat DECODER

and one on the TV. The Rec Type and the TV Type must be the same on all the 4 labels.

In the KIT with Black Box and Sat DECODER there are no. 3 Kit labels, one on the Black

Box, one on the remote control battery compartment and one on the Sat DECODER. The

Rec Type and the TV Type must be the same on all the 3 labels.

In the configuration without KIT, i.e. with the Black Box only, the Kit label is only provided

on the Black Box and on the remote control battery compartment.

The KIT labels of the devices which are contained in this kit are attached on the last page

of this handbook.

Remote

control

Rec Type: Force HD CI+ (A)

TV Type: 19" Teleco United (d)

KIT

Rec Type: Force HD CI+ (A)

TV Type: 19" Teleco United (d)

KIT

Rec Type: Force HD CI+ (A)

TV Type: 19" Teleco United (d)

KIT

Rec Type: Force HD CI+ (A)

TV Type: 19" Teleco United (d)

KIT

Complete Kit with Black Box, Sat Decoder and TV

This configuration will allow you to:

• control your Black Box, TV and DECODER with ONE remote control. You can switch

the whole system on and off via one button.

• control all the three devices via the remote control using the infrared TV sensor.

The following Kits are available:

Complete Kit with Sat FORCE HD CI+ receiver and 19" Teleco United TV

Complete Kit with TivuSat DS510M receiver and 19" Teleco United TV (Italy only)

Complete Kit with TNT SD M6000 receiver and 19" Teleco United TV (France only)

Complete Kit with TNT HD M5200/M7000 receiver and 19" Teleco United TV (France only)

Connection diagrams

16)Connect the grey cable (motors) to the MOTOR UNIT connector and the white coaxial

cable (antenna) to the LNB connector of the Black Box.

17)Connect the BLACK cable of the Black Box to the NEGATIVE POLE of the vehicle 12

Volt Battery and the RED cable to the POSITIVE POLE + (remember not to mix

the + and - poles up), using 2 cables of 2.5 mm2 cross section.

18)The GREEN safety cable of the Black Box must be connected to Pin 15 of the vehicle

ignition key cylinder (D+). In this way, whenever the engine is started, this cable receives

a positive +12 Vdc voltage, which will automatically lower the antenna and lock all functions

of the Black Box simultaneously.

19) Connecting the Decoder

a) Connect the RECEIVER connector of the Black Box to the LNB input of the Decoder

via a coax cable.

b) Connect the RECEIVER IN connector of the Black Box to the Scart output of the

Decoder via a Scart cable.

c) Connect the IR Receiver connector of the Black Box to the IR connector of the

Decoder via a jack-jack lead.

20) Connecting the TV

a) Connect the TV SCART connector of the Black Box to the Scart input of the TV via a

Scart cable.

b) Connect the "IR TV" connector of the Black Box to the "IR" connector of the TV via

a jack-jack lead.

WARNING

Any power connection made in points

other than as indicated (e.g. on the

alternator) can give rise to equipment

malfunction and/or damage resulting

in loss of the warranty.

FORCE HD CI+

DS510M

TV 19" TELECO United

IR ReceiverIR TV

White

Green

Grey

Not connected

redblack

Connecting the complete Kit with a Sat FORCE HD CI+ receiver and a

19" Teleco United TV

DS510M

TV 19" TELECO United

IR TV

Connecting the complete Kit with a TivuSat DS510M receiver and a

19" Teleco United TV (Italy only)

WARNING

Any power connection made in points

other than as indicated (e.g. on the

alternator) can give rise to equipment

malfunction and/or damage resulting

in loss of the warranty.

White

Green

Grey

Not connected

redblack

IR Receiver

ON/OFF

MODEM

VCR

SPDIF

MIR

OUT

AUDIO

VIDEO

LNB

TNT SAT SD M 6000

ANT VCR SCARTSPDIF TV SCART DC IN

TV 19" TELECO United

IR ReceiverIR TV

Connecting the complete Kit with a TNT SD M6000 receiver and a

19" Teleco United TV (France only)

White

Green

Grey

Not connected

redblack

WARNING

Any power connection made in points

other than as indicated (e.g. on the

alternator) can give rise to equipment

malfunction and/or damage resulting

in loss of the warranty.

TNT SAT HD M 5200/M7000

LNB IN HDMI TV SCART IRDC INAUDIO

TV 19" TELECO United

IR ReceiverIR TV

Connecting the complete Kit with a TNT HD M5200/M7000 receiver and a

19" Teleco United TV (France only)

White

Green

Grey

Not connected

redblack

WARNING

Any power connection made in points

other than as indicated (e.g. on the

alternator) can give rise to equipment

malfunction and/or damage resulting

in loss of the warranty.

Kit with Black Box and Sat Decoder, without TV

This configuration will allow you to:

• control your Black Box and DECODER with ONE remote control, but NOT your TV.

You can switch the Black Box and the Decoder on and off via one button.

• In this configuration, you will control the TV via its remote control as it is not part of the Kit.

The following Kits are available:

Kit with Sat FORCE HD CI+ receiver

Kit with TivuSat DS510M receiver (Italy only)

Kit with TNT SD M6000 receiver (France only)

Kit with TNT HD M5200/M7000 receiver (France only)

Connection diagrams

16)Connect the grey cable (motors) to the MOTOR UNIT connector and the white coax

cable (antenna) to the LNB connector of the Black Box.

17)Connect the BLACK cable of the Black Box to the NEGATIVE POLE of the vehicle

12 Volt Battery and the RED cable to the POSITIVE POLE + (remember not to mix

the + and - poles up), using 2 cables of 2.5 mm2 cross section.

18)The GREEN safety cable of the Black Box must be connected to Pin 15 of the vehicle

ignition key cylinder (D+). In this way, whenever the engine is started, this cable receives

a positive +12 Vdc voltage, which will automatically lower the antenna and lock all functions

of the Black Box simultaneously.

19) Connecting the Decoder

a) Connect the RECEIVER connector of the Black Box to the LNB input of the Decoder

via a coax cable.

b) Connect the RECEIVER IN connector of the Black Box to the Scart output of the

Decoder via a Scart cable.

c) Connect the IR Receiver connector of the Black Box to the IR connector of the

Decoder via a jack-jack lead.

20)Connecting the TV

a) Connect the TV SCART connector of the Black Box to the Scart input of the TV via a

Scart cable.

Connecting the Kit with a Sat FORCE HD CI+ Receiver

FORCE HD CI+

MIR

TV Not

Supplied

IR Receiver

WARNING

Any power connection made in points

other than as indicated (e.g. on the

alternator) can give rise to equipment

malfunction and/or damage resulting

in loss of the warranty.

White

Green

Grey

Not

connected

redblack

.Connecting the Kit with a TivuSat DS510M Receiver (Italy only)

DS510M

MIR

TV Not

Supplied

WARNING

Any power connection made in points

other than as indicated (e.g. on the

alternator) can give rise to equipment

malfunction and/or damage resulting

in loss of the warranty.

White

Green

Grey

Not

connected

redblack

IR Receiver

ON/OFF

MODEM

VCR

SPDIF

MIR

OUT

AUDIO

VIDEO

LNB

IR Receiver

Connecting the Kit with a TNT SAT SD M 6000 Receiver (France only)

TNT SAT SD M 6000

ANT VCR SCARTSPDIF TV SCART DC IN

MIR

TV Not

Supplied

WARNING

Any power connection made in points

other than as indicated (e.g. on the

alternator) can give rise to equipment

malfunction and/or damage resulting

in loss of the warranty.

White

Green

Grey

Not

connected

redblack

Page is loading ...

Teleco Flatsat Komfort User manual

Teleco Flatsat Komfort User manual

Teleco Flatsat Komfort User manual

Related papers

Other documents