Light/Thin Crop
Heavy/Tough Crop
Disc Speed
Adjusng Rear Bae Plate — Roll Condioner
Controls windrow height/width. Directs crop ow that aects width.
1. Remove lynch pin (A).
2. Pull lever (B) inboard to disengage bracket (C):
Move lever forward (raise bae) for narrow swath.
Move lever backward (lower bae) for wide swath.
3. Release lever so tab engages the notch in bracket (C).
4. Secure lever with lynch pin (A).
Adjusng Rear Bae Deector Fins
Control material distribuon across windrow (Narrower windrow)
1. Remove ns from storage posion (on top of bae).
2. Posion deector n (A) under bae.
3. Secure with exisng bolt and nut (B) (bolt head facing down).
4. Adjust to approximately 60° angle (as shown).
5. Torque nut to 69 Nm (51 lbf·). Repeat on other side.
Controls windrow width and placement.
1. Loosen locking handle (A).
2. Slide adjuster bar (B) along adjuster
plate (C) to the desired posion.
3. Engage bar (B) into a notch in the
adjuster plate.
4. Tighten locking handle (A).
5. Adjust the other side to the same
posion.
6. Adjust the rear bae as required.
Adjusng Forming Shield Side Deectors — Roll Condioner
For rm and level ground, increase the ground speed to
16 km/h (10 mph) and higher, or unl the quality of
cung and condioning are compromised.
For uneven and loose ground, slow the ground speed to
minimize bouncing and prevent cuerbar damage and
uneven stubble.
Ground Speed Chart
Adjusting the Windrow
Use this card as a guide only. Refer to your operator’s manual for detailed sengs and adjustment procedures.
Deectors are angled outward
for wide swaths (A).
Deectors are angled inward
for narrow swaths (B).
A - acres/hour B - hectares/hour C - km/hour D - mph E - R116 SP F - R113 SP
Subject to change without noce
Adjusng Roll Gap
Increase condioning:
1. Loosen jam nut (A) on both sides of the condioner.
2. Turn lower nut (B) counterclockwise to decrease roll gap (C).
3. Tighten jam nut (A) on both sides of the condioner.
Decrease condioning:
1. Loosen jam nut (A) on both sides of the condioner.
2. Turn lower nut (B) clockwise to increase roll gap (C).
3. Tighten jam nut (A) on both sides of the condioner.
Adjusng Roll Tension
Decrease tension (light crops):
1. Loosen jam nut (A) on both sides of the condioner.
2. On both sides of the condioner, turn bolt (B) counterclockwise to in-
crease exposed thread (C) an equal amount.
3. Tighten jam nut (A) on both sides of the condioner.
Increase tension (heavy or tough crops):
1. Loosen jam nut (A) on both sides of the condioner.
2. Turn bolt (B) clockwise to decrease exposed thread (C) an equal amount
on both sides of the condioner.
3. Tighten jam nut (A) on both sides of the condioner.
NOTE: Factory seng is suitable for most condions.
M1170/M1240 Windrower
1. Turn scroll knob (A) to highlight le oat (B) or right oat (C).
2. Press knob (A) to acvate the selecon.
3. Rotate the scroll knob to adjust the oat seng.
4. Press the scroll knob when nished making seng adjustments.
NOTE: Adjust the oat in small increments.
M155/M155E4/M205 SP Windrower
1. Coarse adjust oat with drawbolts (A) on both sides of windrower:
Turn clockwise to increase oat (makes header lighter).
Turn counterclockwise to decrease oat (makes header heavier).
2. Fine adjust le oat with switch (B) or right oat with switch (C):
Seng displays at locaon (D).
Press + to increase or - to decrease oat.
Setting Float
Shallow Angle
Use the lower posion when the
ground is uneven, or to produce a
high stubble.
Use the upper posion when the
ground is smooth, or to produce a
short stubble.
Skid Shoes
Lower Posion
Use a steep angle when the ground is
rm, level, or smooth.
Use a shallow angle when the ground is
loose or uneven.
Steep Angle
Adjusting Cutting Height
NOTE: Check the oat aer signicantly changing the header angle.
Upper Posion
Adjusting the Conditioner Rolls
Header Angle
/
