2. Extron
  3. XTP T HWP 101 4K
XTP T HWP 101 4K

Extron XTP T HWP 101 4K User manual

  • Hello! I am an AI chatbot trained to assist you with the Extron XTP T HWP 101 4K User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How many output ports does the XTP T HWP 101 4K have?
    What kind of junction box is required for installation?
    What type of cable is recommended for signal output?
    What are the front panel connections?
    How can the transmitter be configured?
    What are the front panel indicators?
1
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
XTP T HWP 101 4K • Setup Guide
The XTP T HWP 101 4K is a single output XTP
decorator-style wallplate transmitter that can be installed in
a 1-gang UL Listed metal junction box or the provided mud
ring. This guide provides instructions for an experienced
installer to install and connect the XTP T HWP 101 4K.
Rear Panel Front Panel
A
XTP output connector
B
USB configuration connector
C
Reset button
D
DC power connector
E
HDMI input
connector
F
Signal LED
indicators
Figure 1. XTP T HWP 101 4K Panel Features
HDMI IN
PWR HDMI HDCP
Extron
Front
XTP T HWP 101 4K
RESET
CONFIG
XTP OUT
POWER
12V
A MAX
0.3
Rear Top
F
A
B
C
D
E
HDMI IN
PWR HDMI HDCP
Extron
HDMI IN
PWR HDMI HDCP
Extron
XTP T HWP 101 4K
Signal Output
Cable
Cable
Clamp
Decorator-style Faceplate
Screws or
Nails
W
all opening is
ush with edge
of box.
Wall Stud
Figure 2. Metal Junction Box Installation
HDMI IN
PWR HDMI HDCP
Extron
HDMI IN
PWR HDMI HDCP
Extron
XTP T HWP 101 4K
Decorator-style Faceplate
Mountin
g
Scr
ew
Backing Clip
Rotate the Backing Clip
out of the way to insert
the mud ring into the wall.
Figure 3. Mud Ring Installation
Installation
Preparation
CAUTION: Risk of personal injury. Failure to check the item
listed below may result in personal injury.
ATTENTION: Failure to check the item listed below may
result in property damage.
NOTE: If a junction box is required, it must be metal.
Ensure the installation meets building, electrical, and safety codes.
Mounting and Cabling
For additional mounting and cabling considerations, see the
XTP T HWP 101 4K User Guide at www.extron.com. For metal
junction boxes, refer to the manufacturer for additional information.
Installation site preparation
1. Use a soft pencil to mark guidelines on the mounting surface.
For accuracy, use a template or the mounting enclosure.
NOTE: Install junction boxes against wall studs.
2. Cut a hole in the wall. To avoid making the hole too big, cut
inside the marked lines.
3. If using the mud ring in a wall with insulation inside, remove
at least six inches of the insulation around the cutout. If a wall
stud interferes with removing the insulation, remove as much
insulation as possible between the cutout and the wall stud.
4. Test the t by inserting the mud ring or metal junction box into
the hole in the wall. If necessary, enlarge the hole as needed.
Metal junction box or mud ring installation
• To install a UL Listed metal junction box, use mounting screws
to fasten the box to a wall stud (see gure 2).
• To install the provided mud ring, attach the mounting screws
to the mud ring and loosely attach backing clips to the ends of
the screws. Rotate the backing clips so the mud ring ts in the
opening and then tighten them to t snugly against the back of
the wall (see gure 3).
2
68-2876-50 Rev. B
04 17
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517
Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001
© 2017 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Rear panel connections
1. Connect a twisted pair cable between the XTP connector (see figure 1,
A
on page 1) of the XTP T HWP 101 4K and an XTP
receiver or XTP matrix switcher.
ATTENTION: Do not connect this connector to a computer data or
telecommunications network.
The XTP T HWP 101 4K is compatible with shielded twisted pair (F/UTP, SF/UTP, and
S/FTP) cable. Extron recommends using the following practices to achieve full
transmission distances up to 330 feet (100 meters) and reduce transmission errors.
• Use Extron XTP DTP 24 SF/UTP cable for the best performance. At a minimum,
Extron recommends 24 AWG, solid conductor, STP cable with a minimum bandwidth
of 400 MHz.
• Terminate cables with shielded connectors to the TIA/EIA-T568B standard.
• Limit the use of more than two pass-through points, which may include patch points,
punch down connectors, couplers, and power injectors. If these pass-through points
are required, use shielded couplers and punch down connectors.
NOTE: When using shielded twisted pair cable in bundles or conduits, consider the following:
• Do not exceed 40% ll capacity in conduits.
• Do not comb the cable for the rst 20 meters, where cables are straightened, aligned, and secured in tight bundles.
• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
• Separate twisted pair cables from AC power cables.
• Signal LED — Lights green when the transmitter outputs a signal to a compatible receiver or matrix switcher.
• Link LED — Lights yellow when an XTP device is connected and communication is established.
2. Power the XTP T HWP 101 4K in one of the following methods:
• Connect the provided external power supply to the 2-pole captive screw connector (
D
).
• Connect an XTP Power Injector to the XTP connection between the transmitter and a locally powered XTP receiver.
• Connect the transmitter to an XTP matrix switcher and enable the remote power feature on the XTP matrix switcher.
Mounting the device to the metal junction box or mud ring
1. Using the provided screws, attach the XTP T HWP 101 4K to the mud ring or metal junction box through the inner screw
holes (see figure 2 or 3 on the previous page).
2. Using the provided screws, attach the faceplate to the XTP T HWP 101 4K through the outer screw holes (see figure 2 or 3).
Front panel connections
Connect a digital video source to the female HDMI connector (
E
). It accepts HDMI, DVI (with an appropriate adapter), or
Dual-Mode DisplayPort video signals.
Configuration and Control
After the transmitter and all connected devices are properly connected and powered on, the system is fully operational. To
congure the transmitter directly, connect a host device to the rear panel USB conguration connector (
B
). On the host
device, use the Extron XTP System Conguration Software or SIS™ Commands in the Extron DataViewer utility (see the
XTP T HWP 101 4K User Guide at www.extron.com for more information).
Front Panel Indicators
• Power LED — Lights when power is applied to the device.
• HDMI LED — Lights when an active input signal is detected.
• HDCP LED — Lights when an input signal is HDCP-compliant.
SignalLink
TIA/EIA-T568B
Pin Wire Color
1 White-orange
2 Orange
3 White-green
4 Blue
5 White-blue
6 Green
7 White-brown
8 Brown
12345678
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
/