Axxess AX-ADXSVI-FT1 Datasheet

Axxess
Brand
Axxess
Model
AX-ADXSVI-FT1
Category
Car kits
Type
Datasheet

Axxess AX-ADXSVI-FT1

The Axxess AX-ADXSVI-FT1 is an accessory and NAV output CAN interface designed for use with Fiat 500 vehicles manufactured from 2012 onwards. It provides a 12-volt 10-amp accessory output and retains retained accessory power (RAP). This interface can be used in both amplified and non-amplified systems and provides NAV outputs for parking brake, reverse, and vehicle speed sensor (VSS).

The AX-ADXSVI-FT1 also includes a prewired ASWC-1 harness for steering wheel audio controls (ASWC-1 sold separately). Additionally, it features high-level speaker input and retains OE BT/USB and 3.5mm audio. This interface is USB updatable for future software updates.

Axxess AX-ADXSVI-FT1

The Axxess AX-ADXSVI-FT1 is an accessory and NAV output CAN interface designed for use with Fiat 500 vehicles manufactured from 2012 onwards. It provides a 12-volt 10-amp accessory output and retains retained accessory power (RAP). This interface can be used in both amplified and non-amplified systems and provides NAV outputs for parking brake, reverse, and vehicle speed sensor (VSS).

The AX-ADXSVI-FT1 also includes a prewired ASWC-1 harness for steering wheel audio controls (ASWC-1 sold separately). Additionally, it features high-level speaker input and retains OE BT/USB and 3.5mm audio. This interface is USB updatable for future software updates.

INSTAX-ADXSVI-FT1
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 12/17/13
INSTAX-ADXSVI-FT1
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 12/17/13
INSTAX-ADXSVI-FT1
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 12/17/13
INSTAX-ADXSVI-FT1
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 12/17/13
AX-ADXSVI-FT1
Fiat 500 accessory and NAV output CAN interface 2012-up
• Providesaccessory(12volt10amp)
• RetainsR.A.P.(retainedaccessorypower)
• Usedinbothamplifiedandnon-amplifiedsystems
• ProvidesNAVoutputs(parkingbrake,reverse,andV.S.S.)
• PrewiredASWC-1harnessincluded(ASWC-1soldseparately)
• Highlevelspeakerinput
• RetainsOEBT/USBand3.5mmaudio
• USBupdateble
Note: ThisharnessmustbeusedinconjunctionwiththeAX-ADXSVI
APPLICATIONS
FIAT
500 2012-up
WIRING UP THE AX-ADXSVI-FT1
• ConnecttheYellowwiretotheradio’s12voltbatteryormemorywire.
• ConnecttheBlackwiretotheradio’sgroundwire.
• ConnecttheRedwiretotheignitionwireoftheaftermarketradio
• ConnecttheOrangewiretotheilluminationwireoftheaftermarketradio.Ifthe
aftermarketradiohasnoilluminationwire,tapeofftheOrangewire.
• Connectthe Blue/White wiretotheradio'sampturnonwire.
• ConnecttheWhitewiretotheleftfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheWhite/Blackwiretotheleftfrontnegativespeakeroutputofthe
aftermarketradio.
AX-ADXSVI-FT1
Fiat 500 accessory and NAV output CAN interface 2012-up
• Providesaccessory(12volt10amp)
• RetainsR.A.P.(retainedaccessorypower)
• Usedinbothamplifiedandnon-amplifiedsystems
• ProvidesNAVoutputs(parkingbrake,reverse,andV.S.S.)
• PrewiredASWC-1harnessincluded(ASWC-1soldseparately)
• Highlevelspeakerinput
• RetainsOEBT/USBand3.5mmaudio
• USBupdateble
Note: ThisharnessmustbeusedinconjunctionwiththeAX-ADXSVI
APPLICATIONS
FIAT
500 2012-up
WIRING UP THE AX-ADXSVI-FT1
• ConnecttheYellowwiretotheradio’s12voltbatteryormemorywire.
• ConnecttheBlackwiretotheradio’sgroundwire.
• ConnecttheRedwiretotheignitionwireoftheaftermarketradio
• ConnecttheOrangewiretotheilluminationwireoftheaftermarketradio.Ifthe
aftermarketradiohasnoilluminationwire,tapeofftheOrangewire.
• Connectthe Blue/White wiretotheradio'sampturnonwire.
• ConnecttheWhitewiretotheleftfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheWhite/Blackwiretotheleftfrontnegativespeakeroutputofthe
aftermarketradio.
AX-ADXSVI-FT1
Fiat 500 accessory and NAV output CAN interface 2012-up
• Providesaccessory(12volt10amp)
• RetainsR.A.P.(retainedaccessorypower)
• Usedinbothamplifiedandnon-amplifiedsystems
• ProvidesNAVoutputs(parkingbrake,reverse,andV.S.S.)
• PrewiredASWC-1harnessincluded(ASWC-1soldseparately)
• Highlevelspeakerinput
• RetainsOEBT/USBand3.5mmaudio
• USBupdateble
Note: ThisharnessmustbeusedinconjunctionwiththeAX-ADXSVI
APPLICATIONS
FIAT
500 2012-up
WIRING UP THE AX-ADXSVI-FT1
• ConnecttheYellowwiretotheradio’s12voltbatteryormemorywire.
• ConnecttheBlackwiretotheradio’sgroundwire.
• ConnecttheRedwiretotheignitionwireoftheaftermarketradio
• ConnecttheOrangewiretotheilluminationwireoftheaftermarketradio.Ifthe
aftermarketradiohasnoilluminationwire,tapeofftheOrangewire.
• Connectthe Blue/White wiretotheradio'sampturnonwire.
• ConnecttheWhitewiretotheleftfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheWhite/Blackwiretotheleftfrontnegativespeakeroutputofthe
aftermarketradio.
AX-ADXSVI-FT1
Fiat 500 accessory and NAV output CAN interface 2012-up
• Providesaccessory(12volt10amp)
• RetainsR.A.P.(retainedaccessorypower)
• Usedinbothamplifiedandnon-amplifiedsystems
• ProvidesNAVoutputs(parkingbrake,reverse,andV.S.S.)
• PrewiredASWC-1harnessincluded(ASWC-1soldseparately)
• Highlevelspeakerinput
• RetainsOEBT/USBand3.5mmaudio
• USBupdateble
Note: ThisharnessmustbeusedinconjunctionwiththeAX-ADXSVI
APPLICATIONS
FIAT
500 2012-up
WIRING UP THE AX-ADXSVI-FT1
• ConnecttheYellowwiretotheradio’s12voltbatteryormemorywire.
• ConnecttheBlackwiretotheradio’sgroundwire.
• ConnecttheRedwiretotheignitionwireoftheaftermarketradio
• ConnecttheOrangewiretotheilluminationwireoftheaftermarketradio.Ifthe
aftermarketradiohasnoilluminationwire,tapeofftheOrangewire.
• Connectthe Blue/White wiretotheradio'sampturnonwire.
• ConnecttheWhitewiretotheleftfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheWhite/Blackwiretotheleftfrontnegativespeakeroutputofthe
aftermarketradio.
INSTAX-ADXSVI-FT1
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 12/17/13
INSTAX-ADXSVI-FT1
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 12/17/13
INSTAX-ADXSVI-FT1
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 12/17/13
INSTAX-ADXSVI-FT1
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 12/17/13
• ConnecttheGraywiretotherightfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheGray/Black wiretotherightfrontnegativespeakeroutputofthe
aftermarketradio.
• ConnecttheGreenwiretotheradio’sleftrearpositivespeakeroutput.
• ConnecttheGreen/Blackwiretotheradio’sleftrearnegativespeakeroutput.
• Connectthe Purplewiretotheradio’srightrearpositivespeakeroutput.
• Connectthe Purple/Blackwiretotheradio’srightrearnegativespeakeroutput.
Thefollowingwiresarefortheaftermarketradiosthathavenavigationbuiltin.
• Connectthe Light Greenwiretotheparkingbrakewireoftheaftermarketnavigation
radio(ifapplicable).
• ConnecttheBlue/PinkwiretotheVSSorspeedsensewireoftheaftermarket
navigationradio(ifapplicable).
• Connectthe Green/Purplewiretothereversewireoftheaftermarketnavigationradio
(ifapplicable).
• PlugtheAUX/3.5mmorBT/USBRCAstotheaftermarketradio'saudioAUXinput.
• Cyclethekeybyturningtheignitiononfor30seconds,then“off”and“on”againto
testtheradio.
ASWC-1 (if installing)
AftertheXSVIisinitialized,plugintheASWCintothe12pinharnessofthe
AX-ADXSVI-FT1andrefertotheASWCinstructions.
Caution: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the
aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Caution: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the
aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Caution: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the
aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Caution: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the
aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
• ConnecttheGraywiretotherightfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheGray/Black wiretotherightfrontnegativespeakeroutputofthe
aftermarketradio.
• ConnecttheGreenwiretotheradio’sleftrearpositivespeakeroutput.
• ConnecttheGreen/Blackwiretotheradio’sleftrearnegativespeakeroutput.
• Connectthe Purplewiretotheradio’srightrearpositivespeakeroutput.
• Connectthe Purple/Blackwiretotheradio’srightrearnegativespeakeroutput.
Thefollowingwiresarefortheaftermarketradiosthathavenavigationbuiltin.
• Connectthe Light Greenwiretotheparkingbrakewireoftheaftermarketnavigation
radio(ifapplicable).
• ConnecttheBlue/PinkwiretotheVSSorspeedsensewireoftheaftermarket
navigationradio(ifapplicable).
• Connectthe Green/Purplewiretothereversewireoftheaftermarketnavigationradio
(ifapplicable).
• PlugtheAUX/3.5mmorBT/USBRCAstotheaftermarketradio'saudioAUXinput.
• Cyclethekeybyturningtheignitiononfor30seconds,then“off”and“on”againto
testtheradio.
ASWC-1 (if installing)
AftertheXSVIisinitialized,plugintheASWCintothe12pinharnessofthe
AX-ADXSVI-FT1andrefertotheASWCinstructions.
• ConnecttheGraywiretotherightfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheGray/Black wiretotherightfrontnegativespeakeroutputofthe
aftermarketradio.
• ConnecttheGreenwiretotheradio’sleftrearpositivespeakeroutput.
• ConnecttheGreen/Blackwiretotheradio’sleftrearnegativespeakeroutput.
• Connectthe Purplewiretotheradio’srightrearpositivespeakeroutput.
• Connectthe Purple/Blackwiretotheradio’srightrearnegativespeakeroutput.
Thefollowingwiresarefortheaftermarketradiosthathavenavigationbuiltin.
• Connectthe Light Greenwiretotheparkingbrakewireoftheaftermarketnavigation
radio(ifapplicable).
• ConnecttheBlue/PinkwiretotheVSSorspeedsensewireoftheaftermarket
navigationradio(ifapplicable).
• Connectthe Green/Purplewiretothereversewireoftheaftermarketnavigationradio
(ifapplicable).
• PlugtheAUX/3.5mmorBT/USBRCAstotheaftermarketradio'saudioAUXinput.
• Cyclethekeybyturningtheignitiononfor30seconds,then“off”and“on”againto
testtheradio.
ASWC-1 (if installing)
AftertheXSVIisinitialized,plugintheASWCintothe12pinharnessofthe
AX-ADXSVI-FT1andrefertotheASWCinstructions.
• ConnecttheGraywiretotherightfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheGray/Black wiretotherightfrontnegativespeakeroutputofthe
aftermarketradio.
• ConnecttheGreenwiretotheradio’sleftrearpositivespeakeroutput.
• ConnecttheGreen/Blackwiretotheradio’sleftrearnegativespeakeroutput.
• Connectthe Purplewiretotheradio’srightrearpositivespeakeroutput.
• Connectthe Purple/Blackwiretotheradio’srightrearnegativespeakeroutput.
Thefollowingwiresarefortheaftermarketradiosthathavenavigationbuiltin.
• Connectthe Light Greenwiretotheparkingbrakewireoftheaftermarketnavigation
radio(ifapplicable).
• ConnecttheBlue/PinkwiretotheVSSorspeedsensewireoftheaftermarket
navigationradio(ifapplicable).
• Connectthe Green/Purplewiretothereversewireoftheaftermarketnavigationradio
(ifapplicable).
• PlugtheAUX/3.5mmorBT/USBRCAstotheaftermarketradio'saudioAUXinput.
• Cyclethekeybyturningtheignitiononfor30seconds,then“off”and“on”againto
testtheradio.
ASWC-1 (if installing)
AftertheXSVIisinitialized,plugintheASWCintothe12pinharnessofthe
AX-ADXSVI-FT1andrefertotheASWCinstructions.
  • Page 1 1
  • Page 2 2

Axxess AX-ADXSVI-FT1 Datasheet

Axxess
Brand
Axxess
Model
AX-ADXSVI-FT1
Category
Car kits
Type
Datasheet

Axxess AX-ADXSVI-FT1

The Axxess AX-ADXSVI-FT1 is an accessory and NAV output CAN interface designed for use with Fiat 500 vehicles manufactured from 2012 onwards. It provides a 12-volt 10-amp accessory output and retains retained accessory power (RAP). This interface can be used in both amplified and non-amplified systems and provides NAV outputs for parking brake, reverse, and vehicle speed sensor (VSS).

The AX-ADXSVI-FT1 also includes a prewired ASWC-1 harness for steering wheel audio controls (ASWC-1 sold separately). Additionally, it features high-level speaker input and retains OE BT/USB and 3.5mm audio. This interface is USB updatable for future software updates.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents