Toro 60in E-Z Vac Triple Bagging System, Z Master G3 Mower User manual

Brand: Toro

Model: 60in E-Z Vac Triple Bagging System, Z Master G3 Mower

Category: Lawnmowers

Type: User manual

This manual is also suitable for

FormNo.3395-248RevB

48inand52inE-ZVacTwin

BaggingSystemor60inand72in

E-ZVacTripleBaggingSystem

ZMasterG3Mower

ModelNo.78562—SerialNo.290000001andUp

ModelNo.78563—SerialNo.290000001andUp

ModelNo.78564—SerialNo.290000001andUp

Registeratwww.Toro.com.

OriginalInstructions(EN)

*3395-248*B

ThisproductcomplieswithallrelevantEuropeandirectives.

Fordetails,pleaseseetheDeclarationofIncorporation(DOI)

atthebackofthispublication.

Introduction

Readthisinformationcarefullytolearnhowtooperateand

maintainyourproductproperlyandtoavoidinjuryand

productdamage.Youareresponsibleforoperatingthe

productproperlyandsafely.

YoumaycontactTorodirectlyatwww.Toro.comforproduct

safetyandoperationtrainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourproductready.Figure1,Figure2andFigure3identies

thelocationofthemodelandserialnumbersontheproduct.

Writethenumbersinthespaceprovided.

Figure1

1.Blowermodelandserialnumberlocation

ModelNo.

SerialNo.

Figure2

48-and52-inchbaggerserialnumber

1.Baggermodelandserialnumberlocation

Figure3

60-and72-inchbaggerserialnumber

1.Baggermodelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhassafety

messagesidentiedbythesafetyalertsymbol(Figure4),

whichsignalsahazardthatmaycauseseriousinjuryordeath

ifyoudonotfollowtherecommendedprecautions.

Figure4

1.Safetyalertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanicalinformation

andNoteemphasizesgeneralinformationworthyofspecial

attention.

8111LyndaleAvenueSouth

Bloomington,MN55420

Contactusatwww.Toro.com.

PrintedintheUSA

AllRightsReserved

Contents

Safety...........................................................................3

SafetyandInstructionalDecals.................................4

Setup............................................................................5

1PreparingtheMachine...........................................6

2InstallingtheSideBumpers....................................6

3InstallingtheBaggerMountingBrackets...................7

4InstallingtheHoodAssemblyandBags....................7

5InstallingtheMuferDeector...............................9

6RoutingtheBlowerBeltintotheBlower

Assembly...........................................................10

7InstallingtheBlowerAssembly..............................10

8InstallingtheDischargeTubes...............................12

9InstallingtheBeltCover........................................16

10InstallingtheWeights..........................................17

11InstallingtheBumpers........................................19

12AdjustingtheParkingBrake.................................19

13CheckingtheTirePressure..................................20

Operation....................................................................20

PositioningtheAdjustableBafe..............................21

EmptyingtheGrassBags.........................................21

ClearingObstructionsfromtheBagger

System..............................................................21

RemovingtheBagger..............................................22

UsingtheGrassDeector.......................................22

TransportingtheMachine........................................22

OperatingTips......................................................22

Maintenance.................................................................24

RecommendedMaintenanceSchedule(s)......................24

CleaningtheHoodScreen.......................................24

CleaningtheBaggerandBags...................................24

InspectingtheBlowerBelt.......................................24

ReplacingtheBlowerBeltfor60-and72-inch

Machines...........................................................24

ReplacingtheBlowerBeltfor48-and52-inch

Machines...........................................................25

CheckingandAdjustingtheBlowerLatch..................25

GreasingtheIdlerArm...........................................26

InspectingtheBagger.............................................26

InspectingtheMowerBlades...................................26

InstallingtheMowerBlades.....................................26

ReplacingtheGrassDeector..................................26

Storage........................................................................27

Troubleshooting...........................................................28

Safety

ThefollowinglistcontainssafetyinformationspecictoToro

productsandothersafetyinformationyoumustknow.

•Becomefamiliarwiththesafeoperationoftheequipment,

withtheoperatorcontrols,andsafetysigns.

•Useextracarewithgrasscatchersorotherattachments.

Thesecanchangetheoperatingcharacteristicsandthe

stabilityofthemachine.

•Followthemanufacturer'srecommendationsforadding

orremovingwheelweightsorcounterweightstoimprove

stability.

•Donotuseagrasscatcheronsteepslopes.Aheavy

grasscatchercouldcauselossofcontroloroverturnthe

machine.

•Slowdownanduseextracareonhillsides.Besureto

travelintherecommendeddirectiononhillsides.Turf

conditionscanaffectthestabilityofthemachine.Use

extremecautionwhileoperatingneardrop-offs.

•Keepallmovementonslopesslowandgradual.Donot

makesuddenchangesinspeed,directionsorturning.

•Thegrasscatchercanobstructtheviewtotherear.Use

extracarewhenoperatinginreverse.

•Usecarewhenloadingorunloadingthemachineintoa

trailerortruck.

•Neveroperatewiththedischargedeectorraised,

removedoraltered,unlessusingagrasscatcher.

•Keephandsandfeetawayfrommovingparts.Donot

makeadjustmentswiththeenginerunning.

•Stoponlevelground,disengagedrives,chockorblock

wheels,shutoffenginebeforeleavingtheoperator's

positionforanyreasonincludingemptyingthegrass

catcheroruncloggingthechute.

•Ifyouremovethegrasscatcher,besuretoinstallany

dischargedeectororguardthatmighthavebeen

removedtoinstallthegrasscatcher.Donotoperatethe

machinewithouteithertheentiregrasscatcherorthe

grassdeectorinplace.

•Stoptheenginebeforeremovingthegrasscatcheror

uncloggingthechute.

•Donotleavegrassingrasscatcherforextendedperiods

oftime.

•Grasscatchercomponentsaresubjecttowear,damage

anddeterioration,whichcouldexposemovingpartsor

allowobjectstobethrown.Frequentlycheckcomponents

andreplacewithmanufacturer'srecommendedparts,

whennecessary.

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedorlost.

1-653558

98-5954

103-3508

106-0871

106-3339

106-5517

1.Warning—donottouchthehotsurface.

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Leftbumper

Rightbumper1

Carriagebolt(3/8x1-1/4inches)

Flangenut(3/8inch)

Installthesidebumpers.

Uppermountingbracket1

Lowermountingbracket1

Carriagebolt(3/8x1-1/4inches)

Carriagebolt(1/2x2–1/2inches)

Flangenut(3/8inch)

Flangenut(1/2inch)

Installthebaggermountingbrackets.

Hoodassembly1

Bag(48-inchand52-inchdecks)

Bag(60-inchand72-inchdecks)

Pinandhairpin-cotterassembly2

Installthehoodassemblyandbags.

Muferdeector

Flangenut(3/8inch)

Carriagebolt(3/8x1-1/4inches)

Installthemuferdeector.

Blowerbelt(fromBlowerandDriveKit)

Routetheblowerbeltintotheblower

assembly.

Blowerassembly(fromtheBlowerand

DriveKit)

Spring(fromtheBlowerandDriveKit)

Installtheblowerassembly.

Uppertube1

Lowertube1

Bolt(#10x3/4inches)

Locknut(#10)

Washer(7/32inch)

Installthedischargetubes.

Beltcover(fromBlowerandDriveKit)

1Installthebeltcover.

Casterweight(ifneeded)

Clevispin

Hairpincotter2

Lockwasher(3/8inch)

Weight-mountbracket1

Bolt(3/8x1-1/2inches)

Flatwasher(3/8inch)

Carriagebolt(5/16x3/4inch)

Flangenut(5/16inch)

Frontweight(48-inch,52-inch,and

60-inchdecks)

Frontweight(72-inchdecks)

Installtheweights.

ProcedureDescription

Qty.

Use

Bumper2

Spacer

Locknut(5/16inch)

Installthebumpers(formachineswith

MyRide™suspensionsystem).

Nopartsrequired

–

Adjusttheparkingbrake.

Nopartsrequired

–

Checkthetirepressure.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

PreparingtheMachine

NoPartsRequired

Procedure

Performthefollowingproceduretopreparethemachinefor

attachingtheblowerandnishingkit.

1.DisengagethePTO,movethemotion-controllevers

totheNEUTRAL-LOCKEDpositionandsettheparking

brake.

2.Stoptheengine,removethekey,andwaitforallmoving

partstostopbeforeleavingtheoperatingposition.

3.Repairallbentordamagedareasofmachinedeckand

replaceanymissingparts.

4.Cleanthemachineofanydebrisonthemachinedeck

orrearpartofthemachinetoeaseinstallation.

InstallingtheSideBumpers

Partsneededforthisprocedure:

Leftbumper

1Rightbumper

Carriagebolt(3/8x1-1/4inches)

Flangenut(3/8inch)

Procedure

1.Removethenutsandboltsholdingthesidebumpers

tothemachine(Figure5).

Note:Discardallnutsandonlythe1boltremoved

fromeachside.

2.Installthenewleftandrightsidebumperswith2

carriagebolts(3/8x1-1/4inches),4previously

removedcarriagebolts,and6angenuts(3/8inch)as

showninFigure5.

Figure5

1.Flangenut(3/8inch)4.Leftbumper

2.Rightbumper

5.Bolt(3/8x1-1/4inches)

3.Useexistingbolts

InstallingtheBaggerMounting

Brackets

Partsneededforthisprocedure:

1Uppermountingbracket

1Lowermountingbracket

Carriagebolt(3/8x1-1/4inches)

Carriagebolt(1/2x2–1/2inches)

Flangenut(3/8inch)

Flangenut(1/2inch)

Procedure

1.Installthelowermountingbrackettothemachine

framewith4carriagebolts(3/8x1-1/4inches)and

4angenuts(3/8inch)asshowninFigure6.

2.Installtheuppermountingbrackettotheleftandright

sidebumperswith2carriagebolts(1/2x2-1/2inches)

and2angenuts(1/2inch)asshowninFigure6.

Figure6

1.Carriagebolt(1/2x2-1/2

inches)

4.Lowermountingbracket

2.Uppermountingbracket

5.Carriagebolt(3/8x1-1/4

inches)

3.Flangenut(1/2inch)6.Flangenut(3/8inch)

InstallingtheHoodAssembly

andBags

Partsneededforthisprocedure:

1Hoodassembly

Bag(48-inchand52-inchdecks)

Bag(60-inchand72-inchdecks)

2Pinandhairpin-cotterassembly

Procedure

1.Positionthehoodassemblyonitsback.

2.Slidehooksontothelowermountingbracket(Figure

7).

3.Rotatethehoodassemblyuponthelowerbagger

mountingbracket(Figure7).

4.Aligntheholeinthebaggerwiththeuppermounting

bracket(Figure7).

5.Installthepinandsecureitwiththehairpincotteron

bothsides(Figure7).

Figure7

1.Lowermountingbracket4.Hairpincotterconnected

tolanyard

2.Hook5.Pinconnectedtolanyard

3.Hoodassembly

6.Installthebagtabintothenotchinthehoodassembly

(Figure8orFigure9).

Note:Dothisforallthebags.

Note:Thebagswillrestonthebaggerframe.

Figure8

Twinbaggershown

1.Hoodassembly4.Notch

2.Bag

5.Baggerframe

3.Bagtab

Figure9

Triplebaggershown

1.Hoodassembly4.Notch

2.Bag

5.Baggerframe

3.Bagtab

7.Lowerthebaggerhoodoverthebags(Figure10or

Figure11).

Figure10

Twinbaggershown

1.Hood3.Baggerlatch

2.Bag4.Latchhook

Figure11

Triplebaggershown

1.Hood3.Baggerlatch

2.Bag4.Latchhook

8.Positionthebaggerlatchunderthelatchhook(Figure

12).

9.Pushdownonbaggerlatchuntilitlocksintoplace

(Figure12).

Figure12

1.Baggerlatch2.Latchhook

InstallingtheMuferDeector

Partsneededforthisprocedure:

Muferdeector

Flangenut(3/8inch)

Carriagebolt(3/8x1-1/4inches)

Procedure

Installthemuferdeectortothesideofthebaggerframe

(Figure13).

Note:Ensurethemuferdeectorispositionedoverthe

tailpipeofthemufer.

Figure13

1.Muferdeector3.Carriagebolt(3/8x1-1/4

inches)

2.Flangenut(3/8inch)

RoutingtheBlowerBeltinto

theBlowerAssembly

Partsneededforthisprocedure:

Blowerbelt(fromBlowerandDriveKit)

Procedure

1.For60-and72-inchmachinedecks,installthebelt

aroundtheblowerpulley(Figure14).

Figure14

Blowerfor60-and72-inchmachines

1.Idlerpulley

4.Springpeg

2.Machinedeckpulley5.Belt

3.Spring

6.Blowerpulley

2.For48-and52-inchmachines,loosenthebelt-guide

bolt(Figure15).

3.Installthebeltaroundtheblowerpulleyandxed-idler

pulley(Figure15).

4.Tightenthebelt-guidebolt.

Figure15

1.Idlerpulley5.Belt

2.Machinedeckpulley6.Belt-guidebolt

3.Spring

7.Fixed-idlerpulley

4.Springpeg

8.Blowerpulley

InstallingtheBlowerAssembly

Partsneededforthisprocedure:

Blowerassembly(fromtheBlowerandDriveKit)

Spring(fromtheBlowerandDriveKit)

Procedure

WARNING

Anuncovereddischargeopeningcouldallowthe

lawnmowertothrowobjectsatyouorbystanders,

resultinginseriousinjury.Also,contactwiththe

bladecouldoccur.

•Neveroperatethelawnmowerunlessyouinstall

acoverplate,amulchplate,oragrasschuteand

catcher.

•Makesurethatthegrassdeectorisinstalled

whenthegrasschuteandcatcherareremoved.

1.Removethesidedischargechutefromthemowerdeck

(Figure16).

Note:Saveallthehardwareandthesidedischarge

chute.Installthesidedischargechutewhenthebagger

andblowerareremoved.

Figure16

1.Bolt

5.Springinstalled

2.Spacer6.Grassdeector

3.Locknut

7.Lendofspring(place

behindthedeckedge

beforeinstallingthebolt)

4.Spring8.J–hookendofspring

2.Slidetheblower-assemblypegintothepivothole

(Figure17orFigure18).

Figure17

48-and52-inchmowerdeckshown

1.Blowerassembly3.Pivothole

2.Mowerdeck4.Blower-assemblypeg

Figure18

60-and72-inchmowerdeckshown

1.Blowerassembly3.Pivothole

2.Mowerdeck4.Blower-assemblypeg

3.Closetheblowerassemblytoseeifthelatchesare

adjustedcorrectly.

Note:Loosenortightentheboltsothelatchesrmly

holdtheblowerassemblyagainstthemowerdeck,but

canbereleasedbyhand(Figure19).

Figure19

1.Latch3.Blowerassembly

2.Bolt

4.InstallthespringasshowninFigure20.

Note:Makesurethatthehooksareinthecorrect

position.

Figure20

1.Spring-loadedidlerpulley

3.Long-hookend

2.Short-hookend

5.Pullthespring-loadedidlerpulleybackandroutethe

beltaroundthemower-deckpulley.

Note:Ensurethatthebeltisroutedaroundtheblower

pulleyscorrectly(Figure21).

Figure21

1.Mower-deckpulley3.Blower

2.Spring-loadedidlerpulley

InstallingtheDischargeTubes

Partsneededforthisprocedure:

1Uppertube

1Lowertube

Bolt(#10x3/4inches)

Locknut(#10)

Washer(7/32inch)

Procedure

Important:Makesurethatthemowerdeckisin

thelowestheight-of-cutpositionwhileinstallingthe

dischargetubes.

Note:Remembertoreplacethegrassdeectorwhenthe

baggerisremovedfromthemachine.RefertoReplacingthe

GrassDeector(page26).

1.DisengagethePTOandsettheparkingbrake.

2.Stoptheengine,removethekey,andwaitforallmoving

partstostopbeforeleavingtheoperatingposition.

3.Lowerthemachinedecktothelowestheight-of-cut

position.

4.Removethebagsforviewingthetubeunderthehood.

5.Installtheuppertubeintothebaggeropeningandpull

itbackoutsothattherubbersealisprotrudingout

(Figure22orFigure23).

Figure22

Twinbaggershown

1.Uppertube3.Baggerhood

2.Baggeropening

Figure23

Triplebaggershown

1.Uppertube3.Baggerhood

2.Baggeropening

6.Withthehoodinthedownposition,measurethe

distancethetubeisinsidethehood.

Measurefromthehoodplatetotheedgeofthetubeas

showninFigure24.

Note:Thisdistanceneedstobe19mm(3/4inch).

Figure24

1.Hoodplate

4.19mm(3/4inch)

2.Uppertube

5.Edgeoftube

3.Hoodinthedownposition

7.Oncethe19mm(3/4inch)measurementhasbeen

achieved,marktheuppertubeontheoutsidewhere

therubbersealprotrudesout(Figure25).

Note:Thisismarkedtoensurethecorrectposition

fortheuppertubewhendrillingtheholesand

connectingtheupperandlowertubes.

Note:Therubbersealmustprotrudeoutfromthe

baggerhood.

Figure25

1.Uppertube3.Baggerhood

2.Rubbersealprotrudingout4.Markhereagainstthe

rubberseal

8.Installthelowertubeintotheuppertube(Figure26).

Figure26

1.Lowertube2.Uppertube

9.Slidethelowertubeontothebootandlatchthem

together(Figure27orFigure28).

Note:Thereisalatchonthetopandbottomofthe

blowerhousing.

Figure27

Twinbaggershown

1.Blowerassembly

3.Latch(twinbaggershown)

2.Lowertube

Figure28

Triplebaggershown

1.Blowerassembly

3.Latch(triplebagger

shown)

2.Lowertube

10.Makesurethatthemachinedeckisinthelowest

height-of-cutposition.

11.ChecktomakesurethatthemarkfromFigure25is

stillinplace.

12.Usingthe3holesorindentationsintheuppertubeasa

template,drill3holes(7/32inchdiameter)wherethe

upperandlowertubesjointogether(Figure29).

Figure29

1.Baggerhood4.Lowertube

2.Uppertube5.Blowerassembly

3.Drill7/32inchdiameter

holeshere(useuppertube

asatemplate)

13.Removethelowertubefromtheblower.

14.Jointheupperandlowertubeswith3bolts(#10x

3/4inches),3atwashers(7/32inch),and3locknuts

(#10)asshowninFigure30.

Figure30

1.Lowertube

4.Locknut(#10)

2.Uppertube

5.Bolt(#10x3/4inches)

3.Flatwasher(7/32inch)

15.Installthelowertubeontotheblowerhousingand

secureitwiththelatches.

16.Installthebagsontothebagger.

InstallingtheBeltCover

Partsneededforthisprocedure:

Beltcover(fromBlowerandDriveKit)

Procedure

1.Lowerthemowerdecktothelowestheight-of-cut

position.

2.Installthenewbeltcoversothatthenotchesonboth

sidesgooverthebelt-coversupportsandsecurethe

latch(Figure31orFigure32).

G009305

Figure31

48-and52-inchbaggershown

1.Beltcover3.Notch

2.Belt-coversupport

G009303

Figure32

60-and72-inchbaggershown

1.Beltcover3.Notch

2.Belt-coversupport

InstallingtheWeights

Partsneededforthisprocedure:

Casterweight(ifneeded)

Clevispin

2Hairpincotter

Lockwasher(3/8inch)

1Weight-mountbracket

Bolt(3/8x1-1/2inches)

Flatwasher(3/8inch)

Carriagebolt(5/16x3/4inch)

Flangenut(5/16inch)

Frontweight(48-inch,52-inch,and60-inchdecks)

Frontweight(72-inchdecks)

Procedure

TocomplywithANSI/OPEIB71.4-2012Standard,add

weightstothemachine.

CAUTION

Thebaggeraddsalotofweighttotherearofthe

machineandmaycauseanunstablecondition

whichcouldresultinalossofcontrol.

Thefollowingtableshowswhatweightsareusedwhena

baggerisinstalled.

Frontweights

used

Casterweights

used

48-inchmachine

deckwithbagger

52-inchmachine

deckwithbagger

60-inchmachine

deckwithbagger

72-inchmachine

deckwithbagger

1.Installcasterweightsonthefrontcasterswithaclevis

pinandahairpincotter(Figure33).

2.Installthenutontoeachtapboltandinstallthetap

boltsintoeachweight(Figure33).

3.Tightenthetapboltsoittouchestheframeandthen

tightenthejamnutagainsttheweight.

Figure33

1.Tapbolt(3/8x1-1/2

inches)

4.Hairpincotter

2.Nut(3/8inch)5.Clevispin

3.Casterweight

6.Installthetapboltagainst

theframeandtightenthe

nut.

4.Installtheweight-mountbracketunderthefootrest

with2carriagebolts(5/16x3/4inch)and2ange

nuts(5/16inch)asshowninFigure34).

Figure34

1.Carriagebolt(5/16x3/4

inch)

3.Flangenut(5/16inch)

2.Weight-mountbracket

5.Installthefrontweightsontopofthefootrest(Figure

35).

6.Securethefrontweightsontopofthefootrestandto

theweight-mountbracketwith6bolts(3/8x1inch),6

lockwashers(3/8inch),3angenuts(3/8inch)and6

atwashers(3/8inch)asshowninFigure35.

Figure35

1.Frontweight

4.Bolt(3/8x1inch)

2.Flatwasher(3/8inch)5.Holeinfootrest

3.Lockwasher(3/8inch)6.Flangenut(3/8inch)

Figure36

1.Weight-mountbracket

3.Lockwasher(3/8inch)

2.Flatwasher(3/8inch)4.Bolt(3/8x1inch)

InstallingtheBumpers

MachineswithMyRide™Suspension

System

Partsneededforthisprocedure:

2Bumper

Spacer

Locknut(5/16inch)

Procedure

For48-inch,52-inch,and60-inchdecks,installthe

bumperstothe2outsideholesofthetoeboard(Figure37).

Figure37

1.Locknut3.Bumper

2.Spacer

For72-inchdecks,installthebumperstothe2insideholes

ofthetoeboard(Figure38).

Figure38

1.Locknut3.Bumper

2.Spacer

AdjustingtheParkingBrake

NoPartsRequired

Procedure

Checktomakesuretheparkingbrakeisadjustedproperly.

RefertoyourOperator’sManualforthecorrectprocedure.

CheckingtheTirePressure

NoPartsRequired

Procedure

Note:Increasethetirepressureduetotheadditionalweight.

Checkandincreasetheairpressureinthefrontcasterwheels

andreartires(Figure39).

Airpressureinthereartires:138kPa(20psi)

Airpressureinthefrontcasterwheels:172kPa(25psi)

Figure39

Operation

Note:Determinetheleftandrightsidesofthemachine

fromthenormaloperatingposition.

Important:Settheparkingbrakewhenleavingthe

machineunattended,evenifjustforafewminutes.

WARNING

Toavoidpersonalinjury,followtheseprocedures:

•Becomefamiliarwithalloperatingandsafety

instructionsinthe

Operator's Man ual

foryour

machinebeforeusingthisattachment.

•Neverremovethebaggerorbaggertubeswhile

theengineisrunning.

•Alwaysshuttheengineoffandwaitforall

movingpartstostopbeforeclearingan

obstructionfromthebaggingsystem.

•Neverdomaintenanceorrepairswhilethe

engineisrunning.

•Settheparkingbrake.

WARNING

Withoutthegrassdeector,baggertubesor

completebaggerassemblymountedinplace,you

andothersareexposedtobladecontactandthrown

debris.Contactwiththerotatingmowerblade(s)

andthrowndebriswillcauseinjuryordeath.

•Alwaysinstallthegrassdeectorwhenremoving

thebaggerandchangingtosidedischarge

mode.

•Ifthegrassdeectoriseverdamaged,replaceit

immediately.Thegrassdeectorroutesmaterial

downtowardtheturf.

•Neverputyourhandsorfeetunderthemower

deck.

•Nevertrytoclearthedischargeareaormower

bladesunlessyoumovethepowertake-off

(PTO)tooffandrotatetheignitionkeytooff.

Alsoremovethekeyandpullthewireoffthe

sparkplug(s).

•Turnofftheenginebeforeuncloggingthe

dischargechute.

Page is loading ...

Toro 60in E-Z Vac Triple Bagging System, Z Master G3 Mower User manual

Brand: Toro

Model: 60in E-Z Vac Triple Bagging System, Z Master G3 Mower

Category: Lawnmowers

Type: User manual

This manual is also suitable for

Download PDF

report

Toro 60in E-Z Vac Triple Bagging System, Z Master G3 Mower User manual

This manual is also suitable for

Toro 60in E-Z Vac Triple Bagging System, Z Master G3 Mower User manual

Related papers

Other documents