AMX CTP-1301 Quick start guide

AMX
Brand
AMX
Model
CTP-1301
Category
Video splitters
Type
Quick start guide

AMX CTP-1301 is a Presentation Connectivity and Transport Kit that enables users to connect and control multiple video sources, audio devices, and control systems in a professional AV setup. It features four inputs, including VGA and HDMI, and an integrated 4K scaler to ensure high-quality video output.

The CTP-1301 supports HDBaseT connectivity, allowing for the transmission of uncompressed 4K video, audio, and control signals over a single Cat5e/6/6a/7 cable. This simplifies installation and reduces cable clutter.

In addition to video and audio connectivity, the CTP-1301 provides various control options. It offers LAN control via Telnet or a web UI, allowing for remote configuration and management. It also features RS232 pass-through, enabling the control of connected devices such as projectors or displays.

AMX CTP-1301 is a Presentation Connectivity and Transport Kit that enables users to connect and control multiple video sources, audio devices, and control systems in a professional AV setup. It features four inputs, including VGA and HDMI, and an integrated 4K scaler to ensure high-quality video output.

The CTP-1301 supports HDBaseT connectivity, allowing for the transmission of uncompressed 4K video, audio, and control signals over a single Cat5e/6/6a/7 cable. This simplifies installation and reduces cable clutter.

In addition to video and audio connectivity, the CTP-1301 provides various control options. It offers LAN control via Telnet or a web UI, allowing for remote configuration and management. It also features RS232 pass-through, enabling the control of connected devices such as projectors or displays.

QUICK START GUIDE
CTP-130 1
Connectivity and Transport Kit - Presentations
Overview
This guide pertains to the CTP-1301 Presentation Connectivity and
Transport Kit (FG1010-710) featuring four inputs with an integrated
4K scaler. The purpose of this document is to illustrate how the
device is to be installed and set up in its simplest configuration by a
trained technician.
What’s in the Box?
The following items are included with the CTP-1301:
•
[1] CTP-1301 TX
•
[1] CTP-1301 RX
•
[1] DC 12V 3A Power Adapter (with US, UK, AUS and
Euro Power Cords)
•
[5] Phoenix Male Connector (3.5mm, 3 Pins)
•
[4] Mounting Bracket
Power
Active power requirements:
•
Voltage, DC (typical): 12V DC 3A
•
Power consumption (max): 7.15W(TX) + 26.83W(RX)
Environmental Requirements
The environmental requirements for the CTP-1301 are as follows:
•
Operating Temperature: 32° F (0° C) to 122° F (50° C)
•
Storage Temperature: 14° F (-10° C) to 140° F (60° C)
•
Operating Humidity: 5% to 85% RH (non-condensing)
•
Storage Humidity: 5% to 85% RH (non-condensing)
Installation
Connections
1.
Connect video source:
Connect the VGA and HDMI sources (such as PC,
Blu- ray player, Apple TV, 4K media player, etc) to
the VGA IN and HDMI IN ports of the CTP-1301 TX.
2.
Connect HDBT OUT:
Connect HDBT OUT of the CTP-1301 TX to HDBT IN of
a receiver like the CTP-1301 RX with a shielded Cat
6/6A/7 cable.
3.
Connect HDMI IN:
Connect an HDMI source to the HDMI IN port of
the CTP-1301 RX.
4.
Connect HDMI OUT:
Connect an HDMI display device (such as projector
or display) to the HDMI OUT port on the CTP-1301 RX.
5.
Connect AUDIO OUT:
If Required, Connect an audio receiver to the AUDIO OUT of
the CTP-1301 RX.
Typical Connection Diagram
6.
Connect for additional control options:
If required, LAN Control (Telnet/Web UI): Connect a PC or
control system to the LAN port of the CTP-1301 RX.
7.
RS232 Pass-through:
If required, connect the RS232-enabled device (e.g. projector)
to RS232 port of the CTP-1301 RX, and connect the projector
screen to RELAY port (1-2) for RS232 signal pass- through.
8.
Connect the power adapter provided to the CTP-1301 RX: One-
way PoH enables power to be sent from CTP-1301 RX to TX along
a single CATX cable, and no additional power adapter is
required at the TX.
9.
Power on all attached devices:
When all is set, check if all LED indicators on the CTP-1301 TX and
RX are normal to ensure installation is successful. For LED
indication, please refer to Panel Description section of the
owner's manual.
Identify the IP addr ess of the CTP-1301
On the CTP-1301 RX, press and hold the HDBT and HDMI Input
buttons for 3 seconds. The current IP address of the device will be
presented on the display connected to the HDMI Out port. Please
note that if the address is typed as http:// or if on
ly the IP address is
typed, it will be redirected to a secure port on an HTTPS://
connection. Also note that the included certificate will most likely
need to be trusted at least once by each browser the first time the
web interface is connected.
From the web interface, the device can be configured with NetLinx
D:P:S configuration, adjust output volume, change IP address, enable
manual switching, etc.
Attaching Installation Brackets
To attach the installation brackets:
1.
Position and install the mounting brackets with the four
mounting screws provided.
location with the mounting screws.
3. Mount and secure the CTP-1301
TX/RX to a surface or a suitable
2.
Repeat steps 1 for the CTP-1301 TX/RX.
2. Repeat step 1 for the other side of the CTP-1301 TX/RX
Additional Document ation
Refer to the AMX CTP-1301 Presentation Connectivity and
Transport Kit users guide for additional details on installing,
upgrading, and controlling the CTP-1301.
© 2017 Harman. All rights reserved. Modero, AMX, AV FOR AN IT WORLD, HARMAN, and their respective logos are registered trademarks
of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective
companies. AMX does
not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice
at any time. The AMX Warranty and Return Policy and related documents can be viewed/downloaded atwww.amx.com.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 | www.AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153
AMX (UK) LTD, AMX by HARMAN - Unit C, Auster Road, Clifton Moor, York, YO30 4GD United Kingdom | +44 1904-343-100 | www.amx.com/eu/
5100545 REV:B
Last Revised: 10/11//2018
CTP-1301 TX
CTP-1301 RX
CTP-1301 RX
Control System
PC
Projector ScreenProjectorBYOD System
HDBT
CTP-1301 TX
Blu-ray PlayerPCPC
HDMI INHDMI
IN
AUDIO
IN
VGA IN
AUDIO
OUT
HDMI
OUT
HDMI IN Relay
Control
RS232
Amplifier
Ethernet Switch
Ethernet
Ethernet
Ethernet
(e.g. NX-3200)
  • Page 1 1

AMX CTP-1301 Quick start guide

AMX
Brand
AMX
Model
CTP-1301
Category
Video splitters
Type
Quick start guide

AMX CTP-1301 is a Presentation Connectivity and Transport Kit that enables users to connect and control multiple video sources, audio devices, and control systems in a professional AV setup. It features four inputs, including VGA and HDMI, and an integrated 4K scaler to ensure high-quality video output.

The CTP-1301 supports HDBaseT connectivity, allowing for the transmission of uncompressed 4K video, audio, and control signals over a single Cat5e/6/6a/7 cable. This simplifies installation and reduces cable clutter.

In addition to video and audio connectivity, the CTP-1301 provides various control options. It offers LAN control via Telnet or a web UI, allowing for remote configuration and management. It also features RS232 pass-through, enabling the control of connected devices such as projectors or displays.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents