AMX VPX-1701 Quick start guide

AMX
Brand
AMX
Model
VPX-1701
Category
Soundbar speakers
Type
Quick start guide
Overview
This guide pertains to the VPX-17014K Scaling Presentation
Switcher(FG1010-357). The purpose of this document is to
illustrate how the device is to be installed and set up in its
simplest configuration by a trained technician.
What’s in the Box?
The following items are included with the VPX-1701:
•
[7] 5-pin Phoenix Male Connector (3.5 mm, 5pins)
•
[1] 6-pin Phoenix Male Connector (3.5 mm, 6pins)
•
[1] AC power cable with US pins
•
[1] AC power cable with UK pins
•
[1] AC power cable with EU pins
•
[2] Mounting ears
•
[8] Mounting screws
Power
Active power requirements:
•
Voltage, AC (typical): 100~240VAC
•
Power consumption (max): 45W
Environ mental Requirements
The environmental requirements for the are as follows:
•
Operating Temperature: 32° F (0° C) to 122° F (50° C)
•
Storage Temperature: -4° F (-20° C) to 140° F (60° C)
•
Operating Humidity: 10% to 90% RH (non-condensing)
•
Storage Humidity: 10% to 90% RH (non-condensing)
Installat ion
Connections
1.
Attach the proper cable from any Video Source to the
Input port on the VPX-1701. There are 2 VGA and 5
HDMI inputs. See switching section for details on which
input is selected as the a ctive source.
2.
Attach a HDMI cable from the VPX-1701 HDMI OUTPUT
port to a display, projector or another sinkdevice.
3.
If required, connect the HDBT OUT port on the VPX-1701to
a HDBT Receiver to work together.
4.
If used, connect a USB Host device to the unit, connect
it to the USB Hos
t Port and make sure the HDBT
Receiver is working in USB device mode.
5.
If required, connect an amplifier, soundbar or other
audio device to the audio o utput on theVPX-1701.
6.
If necessary, the Ethernet port can be connected to a
NetLinx NX Integrated Controller to add system level
control of the unit. Please see www.amx.com for details
on choosing the correct controller and setting up the
network.
7.
Attach the correct AC Plug to the DC Adapter for your
location. Plug in and ti
ghten the DC connector to the
VPX-1701 and plug the adapter into the proper ACoutlet.
Switching Operation
VPX-1701 supports auto switching and manual control from the
front panel.
QUICK START GUIDE
VPX-1701
4K Scaling Presentation Switcher
A.
When Auto Switching is enabled, the unit automatically
switches following the rules below:
1.
If more than one input port has an active signal, the priority
order is: VGA 1=> VGA 2=> HDMI 1=> HDMI 2 => HDMI 3=>
HDMI 4=> HDMI 5.
2.
When a new input is connected the lastconnection made
is the first connection u sed.
3.
When you remove a connection: System Automatically
switches to the highest priority input w ith an active signal
follow the priorities shown in section 1. If all input ports are
not active, the current input port is chosen.
B.
Manual Switching is allowed only when Auto Switchingis
disabled
Note: Auto Switching is e nabled or disabled by using the API
Commands or via the on-board web interface.
Identify the IP address of the VPX-1701
Press an d keep hold the INPUT SELECT button VGA IN1 and VGA IN2
at the same time for 3 seconds, the IP will be presented on the
display connected to the HDMI OUT port.
Please note that if the address is typed as http:// or if only the IP
address is typed, it will be redirected to a secure port on an H TTPS://
connection. Also note that the included certificate will most likely
need to be trusted at least once by each browser the first time the
web inte
rface is connected.
From the web interface, the device can be configured with NetLinx
D:P:S configuration, adjust output volume, change IP address,
enable manual switching, etc.
Attaching Insta llation Brackets
To a ttach the installation brackets:
1.
Attach the i nstallation bracket to the enclosure using the
screws that were provided in the packageseparately.
2.
The bracket is attached to the enclosure as shown.
3.
Repeat steps 1-2 for the other side o f the unit.
4.
Attach the brackets to the surface or rack you want to hold
the unit against using the screws (provided byothers).
Mounting Screws (x2 per side)
Additional Documentation
Additional documentation for this device i s available at
www.amx.com. Refer to the AMX VPX-1701 4K Scaling
Presentation Switcher Instruction Manual for additional d etail s on
typical system diagrams, installing, upgrading, and controlling
the VPX-1701.
© 2017 Har man. All rights reserved. Modero, AMX, AV FOR AN IT WORLD, HARMAN, and their respective log os are registered trademarks of
HARMAN. Oracle, Java and any oth er company or brand name referenced may be trademarks/registered trademarks of their respective companies.
AMX does not assume responsibility for errors or omissions. AMX also reserves the r ight to alter specifications without prior notice at any time.
The AMX Warranty a nd Return Policy and related d ocumen
ts can be viewed/downloaded at www.amx.com.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153
AMX (UK) LTD, AMX by HARMAN - Unit C, Auster Road, Clifton Moor, York, YO30 4GD United Kingdom ? +44 1904-343-100 ? www.amx.com/eu/
5100550 REV: B
Last Revised:10/11/2018
VPX-1701
  • Page 1 1

AMX VPX-1701 Quick start guide

AMX
Brand
AMX
Model
VPX-1701
Category
Soundbar speakers
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents