Legrand 6 Room Audio Module, IS-0132 Installation guide

6 Room Audio Module, IS-0132
Legrand
Brand
Legrand
Model
6 Room Audio Module, IS-0132
Type
Installation guide

Legrand 6 Room Audio Module, IS-0132, distributes amplified stereo and audio sources to six pairs of speakers through impedance matching volume controls. It's designed for installation in On-Q Home service center enclosures, accommodates up to 14 AWG speaker cable, and features removable terminal blocks for easier wire termination. Additionally, the module occupies minimal space, measuring half an enclosure width and taking up only three vertical inches.

Legrand 6 Room Audio Module, IS-0132, distributes amplified stereo and audio sources to six pairs of speakers through impedance matching volume controls. It's designed for installation in On-Q Home service center enclosures, accommodates up to 14 AWG speaker cable, and features removable terminal blocks for easier wire termination. Additionally, the module occupies minimal space, measuring half an enclosure width and taking up only three vertical inches.

INSTRUCTION/INSTALLATION SHEET
6 ROOM AUDIO DISTRIBUTION MODULE IS-0132 REV.A
1. Introduction
On-
Q
Home 6 Room Audio
Distribution Module
The On-Q Home 6 Room Audio Distribution Module, P/N 364454-01
(see Figure 1), provides the distribution of an amplified stereo and audio source
to six (6) pairs of speakers through On-Q Home Impedance Matching Volume
Controls, P/N 364520-xx. The module can be mounted in any On-Q Home
service center enclosure and can accommodate up to 14 AWG speaker cable.
2. Description
Figure 1
The On-Q Home 6 Room Audio Distribution Module has fourteen (14) removable two-position terminal blocks which are
connected in parallel on a printed circuit board. The terminal blocks can be removed to allow for easier wire termination. The
module is half an enclosure width and occupies three (3) vertical inches of space.
3. Installation
NOTE: Failure to ensure proper impedance to the source my result in damage to audio equipment and speakers.
A. Mounting in enclosure, (see Figure 2)
1) Align tabs on module with slots on the rear of the enclosure.
2) Insert tabs by angling module away from the back of the enclosure.
3) Rotate the module and insert fasteners on module into corresponding
holes on the rear of the enclosure. (Plunger must be in a pulled
position for fastener to engage hole.)
4) Push plunger in to lock module in place. Pull on module to ensure
module is locked properly in place.
B. Connecting Wiring
1) Identify the source (from media center) pair of speaker wires. P
loosely a
osition
long the side of the enclosure and position over terminal
2)
inal, keeping left and right “+” and “-”
4) 1-3 for each set of speakers.
iring layout label on
NOTE: THIS MODULE DOES NOT PROVIDE IMPEDANCE MATCHING ON ITS OWN.
block marked source. Trim with 2-3 inches of excess.
Strip ends 1/4 to 3/8 inch.
3) Insert into appropriate term
identified.
Repeat steps
5) Record source and speaker locations on w
enclosure cover.
Figure 2
Page 1 of 1
301 Fulling Mill Road, Suite G ©Copyright 2004 by OnQ Technologies, Inc All Rights Reserved.
Middletown, PA 17057 www.onqhome.com
(800)-321-2343
Innovations in Home Living.
  • Page 1 1

Legrand 6 Room Audio Module, IS-0132 Installation guide

6 Room Audio Module, IS-0132
Legrand
Brand
Legrand
Model
6 Room Audio Module, IS-0132
Type
Installation guide

Legrand 6 Room Audio Module, IS-0132, distributes amplified stereo and audio sources to six pairs of speakers through impedance matching volume controls. It's designed for installation in On-Q Home service center enclosures, accommodates up to 14 AWG speaker cable, and features removable terminal blocks for easier wire termination. Additionally, the module occupies minimal space, measuring half an enclosure width and taking up only three vertical inches.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents