Electric Standing Desk
User Manual
Model: AIT001G
TABLE OF CONTENTS
Parts and Hardware List
Parts
01
02
Hardware
02
Step 1 03
Step 2 04
Step 3 04
Step 4 05
Step 5 05
Step 6 06
07Step 7
Operation Guide 08
PARTS AND HARDWARE LIST
NO Component Name Qty
Foot Pad
Legs
M6*12 Screw
ST4.8*25 Screw
ST3.5*19 Screw
Cross Bar
Bracket
Foot Margin
M6*14 Screw
Rubber Cushion
Plastic Pad
ST4.8*19 Screw
1
2
3
4
5
A
B
C
D
E
F
G
4
2
2
2
1
Control Box
6
1
Key Pad
7
1
2
6
4mm Hex Spanner
H
1
Cable Tie
I
5
12
6
8
6
2
BA
C
D
E
I
F G
H
4
5
1
2
3
6
7
01
PARTS
HARDWARE
5 Crossbar x1
1 Foot Pad x4
2 Foot Margin x2
6 Control Box x 1 7 Keypad x1
3 Bracket x2 4 Legs x2
ST3.5*19
Screw x 2
ST4.8*19
Screw x 2
ST4.8*25
Screw x 6
M6*12
Screw x 12
Plastic Pad x6 Rubber Cushion x 6
M6*14
Screw x8
4mm
Hex Spanner x1
Cable Tie x 5
02
A
F G H I
B C D E
STEP 1
Loosen 8 pcs M6*10screws,they were attached before packing.
Adjust the crossbar to proper position and then tighten the 8 pcs
screws.
M6*10 screw 8 pcs
4mm Hex Spanner
03
Tool Required H
STEP 2
STEP 3
Attach foot margins to leg using 8 pcs M6*14 screws and tighten with
4mm hex spanner.
Attach legs to crossbar ends using 8 pcs M6*12 screws.
4mm Hex Spanner
M6*12screw 8 pcs
M6*14 screws 8 pcs
4mm Hex Spanner
04
Tool Required H
Hardware Required
A Screws
Tool Required H
Hardware Required
B Screws
4mm Hex Spanner
STEP 4
Attach brackets to each crossbar end using 4 pcs M6*12 screws.
STEP 5
Put rubber cushions and plastic pads on the side brackets and
crossbar.
M6*12screw 4 pcs
Plastic Pad Rubber Cushion
05
Tool Required H
Hardware Required
A Screws
Hardware Required : F & G
STEP 6
ST4.8*25 Screw 6 pcs
ST4.8*19crew 2 pcs
ST3.5*19 2 pcs
Attach the brackets and the crossbar to the table top using 6 pcs
ST4.8*25 screws.Attach the control box using 2pcs ST4.8*19 screws
Attach the keypad to the table top using 2 pcs
ST3.5*19 screws.
06
Tool Required
Drill / Driver
Hardware Required
C&D&E Screws
STEP 7
Plug cables from two motors to the control box and cable from the
keypad.
07
Operation Guide
08
Activating & Troubleshooting
Lock and Unlock
You will need to activate the memory keypad once the desk is fully assembled, Side note :
if the frame doesn’t seem to be working properly, rest assured that most issues can be
fixed using the exact same activation process.
1.If the handset locked, first step is unlock.
2.Begin by pressing and holding the “Up” and “Down” buttons at the same time.
3.Continue to hold as the frame lowers itself all the way down (if extended ), you will hear a
slight beep sound followed by a brief flash on the display.
4.Press the “Up” button once to engage the motors, your desk should be activated and
ready to go.
Press the lock button for 1 second handset locked.
Press the lock button for 3 seconds handset unlock.
To preset a specific height, drive the desk to desired height, press “Up” and 1 buttons at the
same time for about 2 seconds, “P1” should appear on the display,repeat the procedure for
button 2.
Press “1” “2” and “unlock” button together for about 5 seconds, “C-I” should appear on the
display, press the “2” button you should see “I ” displayed, you have programmed the
handset from centimeters to inches.
Press“1” “2” and “unlock” button together for about 5 seconds, “C-I” should appear on the
display, press the “1” button you should see “C” displayed, you have programmed the
handset from inches back to centimeters.
Memory Function
Programming Alternative Measurements
Revert Back to Centimeters
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
AITERMINAL AIT001G User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
bol com Electric Standing Desk User manual
-
AOKE YDZF3 Series Assembly Instructions
-
EFFYDESK Home Frame 2022 User manual
-
Keys Fitness 4500T User manual
-
AbCoaster PRO Owner's manual
-
EFFYDESK ED-BIZ User manual
-
-
EFFYDESK Height-Adjustable Electric Standing Desk User manual
-
-
