AITERMINAL Electric Standing Desk Frame Single Motor Adjustable Motorized Stand Up Desk-Gray(Frame Only) User manual

Brand
AITERMINAL
Model
Electric Standing Desk Frame Single Motor Adjustable Motorized Stand Up Desk-Gray(Frame Only)
Type
User manual

AITERMINAL Electric Standing Desk Frame Single Motor Adjustable Motorized Stand Up Desk-Gray(Frame Only) is a height-adjustable standing desk frame that allows you to alternate between sitting and standing throughout the day, promoting better posture, increased productivity, and reduced risk of chronic health conditions associated with prolonged sitting.

The desk frame is constructed from durable steel and features a powerful single motor that обеспечивает smooth and quiet height adjustment. The frame is easy to assemble and can be adjusted to a height range of 27.6" to 46.5".

The desk frame comes with a programmable keypad that allows you to save four different height presets. The keypad also features a lock function to prevent accidental height adjustments.

AITERMINAL Electric Standing Desk Frame Single Motor Adjustable Motorized Stand Up Desk-Gray(Frame Only) is a height-adjustable standing desk frame that allows you to alternate between sitting and standing throughout the day, promoting better posture, increased productivity, and reduced risk of chronic health conditions associated with prolonged sitting.

The desk frame is constructed from durable steel and features a powerful single motor that обеспечивает smooth and quiet height adjustment. The frame is easy to assemble and can be adjusted to a height range of 27.6" to 46.5".

The desk frame comes with a programmable keypad that allows you to save four different height presets. The keypad also features a lock function to prevent accidental height adjustments.

Electric Standing Desk
User Manual
Model: AIT002W
TABLE OF CONTENTS
Parts and Hardware List
Parts
01
02
Hardware
02
Step 1 03
Step 2 04
Step 3 04
Step 4 05
Step 5 05
Step 6 06
06Step 7
07Step 8
07Step 9
08Step 10
09Step 11
Operation Guide
10
PARTS AND HARDWARE LIST
NO Component Name Qty
Crossbar
Foot Pad
ST4.8*19 Screw
4mm Hex Spanner
M6*14 Screw
Driveshaft
Right Leg
Foot Margin
Bracket
Rubber Cushion
ST3.5*19 Screw
M6*12 Screw
Plastic Pad
ST4.8*25 Screw
1
2
3
4
5
6
7
A
B
C
D
1
2
2
4
1
Left Leg
1
1
Control Box
8
1
Key Pad
9
1
8
1
2
2
6
12
6
6
A B C
D
E F G
H I
J
7
1
4
8
2
3
6
5
9
01
E
F
H
G
Wrench
I
1
Cable Tie
J
1
PARTS
HARDWARE
5 Right Leg x1
2 Bracket x2
7 Driveshaft x1
9 Key Pad x1 10 Power Cord x18 Control Box x1
3 Foot Margin x2
4 Foot Pad x4
ST3.5*19
Screw x 2
ST4.8*19
Screw x 2
ST4.8*25
Screw x 6
M6*12
Screw x 12
Plastic Pad x 6 Rubber Cushion
x 6
M6*14
Screw x 8
4mm Hex
Spanner x1
6 Left Leg x1
Wrench x1
1 Crossbar x1
Cable Tie x 5
02
A B C D E
JIHGF
STEP 1
4mm Hex Spanner
03
Loosen 8 pcs M6*10screws,they were attached before packing.
Adjust the beam to proper position and then tighten the screws.
Tool Required H
STEP 2
STEP 3
Attach foot margins to leg using 8 pcs M6*14 screws and tighten
with 4mm hex spanner.
Attach legs to crossbar ends using 8 pcs M6*12 screws.
4mm Hex Spanner M6*12screw 8PCS
04
Tool Required H
Hardware Required
B Screws
M6*14 screws 8pcs
4mm Hex Spanner
Tool Required H
Hardware Required
A Screws
STEP 4
Attach brackets to each crossbar end using 4 pcs M6*12 screws.
STEP 5
Loosen the left nut from the driveshaft using wrench.Turn the left
nut counterclockwise to remove it from the driveshaft.Keep the
plastic grommet inside the left nut.
Left Nut
Right Nut
Center Rod
05
4mm Hex Spanner
M6*12 screw 4pcs
Tool Required H
Hardware Required
B Screws
Tool Required I
Wrench
Nut
STEP 6
STEP 7
Slightly loosen the right nut by turning it once again. Pull the
center rod out and insert it into the left leg.
Push the center rod all the way in.Then leave a small gap(about
0.2 in)between center rod and left leg, turn the right nut to lock the
drive
shaft in place.Do not let the right nut touch the left leg.
Use the wrench to tighten the left nut and right nut.
Insert the left nut and plastic grommet into the right leg. Pay atten-
Turn the left nut clockwise to firmly lock the driveshaft in place.
Leave a small gap(about 0.2in) between the left nut and the right
leg so they won't block the driveshaft when it turns.
06
Tool Required I
tion to the insert direction.Push the driveshaft all the way in.
Wrench
STEP 8
Put rubber cushions and plastic pads on the side brackets and
the crossbar.
STEP 9
Attach the brackets and the crossbar to the table top using 6 pcs
ST4.8*25 screws.
Plastic Pad Rubber Cushion
ST4.8*25 Screw 6pcs
07
Hardware Required
F & G
Tool Required
Drill / Driver
Hardware Required
E Screws
STEP 10
Attach the control box using 2 pcs ST4.8*19 screws,then attach
the keypad to the table top using 2 pcs ST3.5*19 screws.
ST4.8*19 Screw 2pcs
ST3.5*19 Screw 2pcs
08
Tool Required
Drill / Driver
Hardware Required
C & D Screws
Plug cables from the motor to the control box and cable from the
keypad.
STEP 11
09
Operation Guide
10
Activating & Troubleshooting
Lock and Unlock
You will need to activate the memory keypad once the desk is fully assembled, Side note :
if the frame doesn’t seem to be working properly, rest assured that most issues can be
fixed using the exact same activation process.
1.If the handset locked, first step is unlock.
2.Begin by pressing and holding the “Up” and “Down” buttons at the same time.
3.Continue to hold as the frame lowers itself all the way down (if extended ), you will hear a
slight beep sound followed by a brief flash on the display.
4.Press the “Up” button once to engage the motors, your desk should be activated and
ready to go.
Press the lock button for 1 second handset locked.
Press the lock button for 3 seconds handset unlock.
To preset a specific height, drive the desk to desired height, press “Up” and 1 buttons at the
same time for about 2 seconds, “P1” should appear on the display,repeat the procedure for
button 2.
Press “1” “2” and “unlock” button together for about 5 seconds, “C-I” should appear on the
display, press the “2” button you should see “I”displayed, you have programmed the
handset from centimeters to inches.
Press“1” “2” and “unlock” button together for about 5 seconds, “C-I” should appear on the
display, press the “1” button you should see “C” displayed, you have programmed the
handset from inches back to centimeters.
Memory Function
Programming Alternative Measurements
Revert Back to Centimeters
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

AITERMINAL Electric Standing Desk Frame Single Motor Adjustable Motorized Stand Up Desk-Gray(Frame Only) User manual

Brand
AITERMINAL
Model
Electric Standing Desk Frame Single Motor Adjustable Motorized Stand Up Desk-Gray(Frame Only)
Type
User manual

AITERMINAL Electric Standing Desk Frame Single Motor Adjustable Motorized Stand Up Desk-Gray(Frame Only) is a height-adjustable standing desk frame that allows you to alternate between sitting and standing throughout the day, promoting better posture, increased productivity, and reduced risk of chronic health conditions associated with prolonged sitting.

The desk frame is constructed from durable steel and features a powerful single motor that обеспечивает smooth and quiet height adjustment. The frame is easy to assemble and can be adjusted to a height range of 27.6" to 46.5".

The desk frame comes with a programmable keypad that allows you to save four different height presets. The keypad also features a lock function to prevent accidental height adjustments.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents