Vector SPKST72 Operating instructions
- Type
- Operating instructions
S
NOW
P
LOW
&
MOUNT
ASS
EMBLY
Before You Start
A
IMPORTANT:
732001150100 62" Snow Plow Kit, Blade, & Push Tube
732001150200 72" Snow Plow Kit, Blade, & Push Tube
732001150300 Snow Plow Mount Bracket, 450 ~ 1000 Utility Model
732001150400 Snow Plow Mount Bracke, ATV model
732001150500 Snow Plow Mount Bracket, 1000cc Spo Model
Manual No. 80-20PLOW
2.
** **
2.
7.
!! ! OPERATION!!!
Assembly Instructions
Position Lever ahead and turn the blade to the desired
position. The Lever will spring back when the blade is at
the correct angle.
The blade skids are adjustable so the blade can be
lowered but still held a certain distance off the ground.
The blade is designed to trip when it strikes an object or
digs in too far. When pressure is released the blade
springs back into position. Blade spring tension may be
set stiffer by tightening the Locknuts on the bottom of the
Eyebolts. For less spring tension, loosen the Locknuts.
Do not exceed 5 MPH with blade installed.
Operate with extreme caution on slopes, steep grades
and rough terrain.
Keep away from blade and moving parts during
operation.
When plowing snow or dirt into a pile, start backing up
before raising the blade.
Do not ram the blade into the pile ** SLOW DOWN
BEFORE HITTING THE PILE. **
Be aware of possible hidden objects under snow.
Wear head protection, safety glasses and shoes as
recommended in the machine's Operator's Manual.
Allow no riders on blade or machine while moving or
stationary.
Keep bystanders away from blade and machine while
moving or stationary.
When blade is not in use, turn of the engine, set and lock
brakes, and lower blade to down position.
Only mature adults over the age of 16 should operate the
machinery. Do not operate this machinery if you are
under the age of 16.
Please read and follow all of the instructions in the
owner?s manual.
Please read and follow all of the instructions in the
machine's operations manual.
Keep all bystanders a minimum of 15 Meters away from
the machine and Blade when it is in operation.
Do not use this equipment at night (in the dark) or under
poor weather conditions, unless your machine has
adequate lighting, which produces clear safe vision.
Due to the extra length of the blade, loss of directional
control may result when pushing heavy material.
Use with Caution!
A detailed listing of parts for this accessory kit is
provided on page 3-
6
. Use the list as a checklist to
inventory parts received. Please contact your local
HISUN dealer of any missing hardware.
! Due to reduced ground clea
rance remove plow Mount
Brackets before trail riding.
! Do not exceed 5 MPH with th
e blade or its brackets
installed
OPERATION TIPS
! When plowing snow or dirt into a pile, back away from
the pile before attempting to raise the blade
!
For best results set the suspension to the stiffest setting
if possible
! The Blade is shipped with the Blade Skids mounted
upside down for boxing. Be sure to mount the Skids
properly before using your blade.
MAINTENANCE
! Periodically check for wear and tightness of all bolts,
nuts and fasteners. Replace or tighten as necessary.
Grease all pivot points and hinges as needed
PUSH TUBE TO BLADE BRACKET ASSEMBLY
S/N
NAME
PART NO.
QTY
REMARKS
1
Main Push Tube
81200-1001
1
2
Mid Disc
81312-1001
1
3
Swivel Bracket
81311-1001
1
4
Top Locking Plate
81321-1001
1
5
Bolt M8x25mm
9310708025060
6
6
Adjusting Handle
81313-1001
1
7
Pulley Plate
81332-1001
2
8
Pin M10x25mm
GB/T 800-1986
1
9
Pulley
81331-1001
1
10
Pin M8x25mm
GB/T 800-1986
1
11
Lock Nut M8 B09M827
6
12
Socket Head Bolt M10x16mm
GB/T 70.1-2000
2
13
Lock Nut M10 B10M1012527
2
14
Spring
81333-1001
1
15
Split Pin
QC/T623 Q501
2
16
Washer M10
GB/T 5286-2001
1
17
Washer M8 461681150000
1
18
Lock Pin M10 x 50mm
GB/T 882-1986
2
19
Mount Bracket
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
See page 5
FASTENER THREAD SIZE AND TORQUE: 8MM BOLTS AND NUTS IS 10-15 FT.LBS
10MM BOLTS AN
D NUTS IS 20-25 FT.LBS.
12MM BOLTS AND NUTS IS 35-40 FT.LBS.
BLADE TO BRACKET ASSEMBLY
S/N
NAME
PART NO.
QTY
REMARKS
20
Snow Plow Blade
81100-1001
1
21
Bolt M12*30
GB/T 16674.1-2004
2
22
Washer
81316-1001
2
23
Mid Washer
81317-1001
2
24
Lock Nut M12
GB/T 6183.1-2000
2
25
Leveling Skid Feet
P115000893020000
2
26
Nut M14
GB/T 41-2000
4
27
Tension Spring
81334-1001
2
28
Eye Bolts
81334-1001
2
29
Washer M8
GB/T 5286-2001
4
30
Nut M8
GB/T 41-2000
4
FASTENER THREAD SIZE AND TORQUE: 8MM BOLTS AND NUTS IS 10-15 FT.LB
S
10MM BOLTS AN
D NUTS IS 20-25 FT.LBS.
12MM BOLTS AND NUTS IS 35-40 FT.LBS.
** PLEASE INSTALL THE “TENSION SPRINGS” WITH CONSTANT TENSION, YOU CAN ADJUST THE “EYE
BOLTS” FOR THE TENSION DESIRED.
** YOU WILL NEED TO ADJUST THE “ LEVELING SKID FEET” TO ALLOW THE BLADE TO SLIGHTLY
CONTACT GROUND WHEN FULLY LOWERED.
26
27
28
29
30
21
20
22
23
24
25
COMPLETED ASSEMBLY
VEHICLE PLOW MOUNT BRACKETS
1. 1000cc Sport Plow Mount Bracket
2. Hisun Part Number: 732001150500
1. 450 ~ 1000 Utility Plow Mount Bracket
2. Hisun Part Number: 732001150300
1. ATV Plow Mount Bracket
2. Hisun Part Number: 732001150400
UTILITY MODEL - 450cc ~ 1000cc
SPORT MODEL - Strike 1000
ATV MODEL - 550cc ~ 1000cc
Sport Mount Bracket - Strike 1000
INSTALLATION INSTRUCTIONS:
1. Locate and remove the rear 10mm bolts (A) that
secure the winch to the frame. Shown in Figure 1.
2. Remove the 2 rectangle plastic caps from the
frame tubing.
3. Loosely tighten the 10mm bolts from #1 above.
4. Adjust bracket so that both holes align to the
center of the frame tubing on the left and right
(B).
5. Drill (4) holes through the frame tubing so that
the hold down bracket can be slid into the tubing
and secured with the 100mm hardware.
6. When completed the bracket assembly should
look like Figure 2.
7. Torque all hardware to 20-25 ft.lbs.
Figure 2
Figure 1
B
10MM BOLTS AND NUTS TORQUE TO 20-25 FT.LBS.
Qty.
Fastener Components:
Part Description
4................. Hex Bolt M10x1.25x30mm
4................. Lock Washer M10
4................. Flat Washers M10
PART # 732001150500
A
Utility Mount Bracket - 450cc ~ 1000cc
PART # 732001150300
Fastener Components:
Qty. Part Description
4................. M10x1.25x30mm Hex Bolt
4................. M10 Lock Washer
4................. M10 Flat Washers
INSTALLATION INSTRUCTIONS:
1. Locate and remove bolts (A) on the lower part of
the front bumper. Shown in Figure 2.
2. Slide the plow mount between the bumper and the
frame. Line it up and attach using the hardware
provided in slots (B) underneath the frame shown
in Figure 3. Loosely tighten bolts.
3. With the hardware provided reattach the bumper
to the frame going through the mount slots (C).
Shown in Figure 4.
4. Center the mount and tighten all hardware down
evenly.
Figure 3
Figure 4
Figure 2
B
A
A
C
10MM BOLTS AND NUTS TORQUE TO 20-25 FT.LBS.
ATV Mount Bracket - 550cc ~ 1000cc
PART # 732001150400
Fastener Components:
Qty. Part Description
4................. U Bolts
8.................
M8 Flat Washers
8.................
M8 Lock Washers
INSTALLATION INSTRUCTIONS:
1. Remove both front and middle protection cover
from frame (A). Set protective covers to the side.
Shown in Figure 1.
2. Place the Plow Mount up against the frame so
that the frame will be centered between the holes
but as far toward the front of the ATV as
possible.
3. Install U-bolts and hardware. (Figure 2)
4. You can align the protective covers back up and
drill 3/4" holes so that when the covers will
secure back to the frame.
Figure 1
A
10MM BOLTS AND NUTS TORQUE TO 20-25 F
T.LBS.
8.................
M8 Hex Nuts
Figure 2
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Vector SPKST72 Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Sanus M10KIT Installation guide
-
Meyer 09917 Operating instructions
-
Denali MA11151 Quick Manual
-
KFI Products 106245 User manual
-
Suzuki LT160 User manual
-
Draw-Tite 75123 Installation guide
-
Kellfri 37-SBATV3 Owner's manual
-
Detail K2 AVAL8219ELT User manual
-
MOOSE V-Plow Operating instructions
-
DK2 AVAL8219 User manual
