Installation Instructions for Hisun Snow Plow
1. Remove all components from the shipping carton and lay them out for easy reference.
2. Refer to the attached diagram below and find the following parts: #19 (Locking Plate), #20
(Mid Positioning Plate), and #21 (Swivel Plate).
3. As shown in picture, install the parts #19, #20, #21 on the bracket #22 in the order shown.
Secure part #11 (Setting Spring Bolt) bottom upward, while other 5 bolts should be
assembled from the top downward. In addition to the other washers shown, it is also very
important to note that there are (6 quantity) #17 (Washer 8mm) between part #20 and
part #22. Use the #16 bolts, #17 washers, and #18 Lock nuts to secure the parts #19,
#20, and #21 to the #22 (Main Push Tube). Secure the lock nuts tightly.
4. Use the part #15 (Adjust Handle and Wench Hook Pin) to connect part #10 (Adjusting
Handle), part #14 (Hook for Wench Connection) with part #19 (Locking plate). Note 2 #12
(Washers 10mm) must be placed on the outside edges of the #14 (Hook for Wench
Connection) before the #15 pin is
inserted through the #10 (Adjusting
Handle). Use the #13 (Cotter Pin) to
secure the #15 pin. Bend the ends of
the #13 (Cotter Pin) to secure #10 Pin.
5. Make sure part 11# (Setting Bolt
Spring) is on the end of part 10#
(Adjusting Handle).
6. Install the 2 pcs part #2 (Leveling Skid Plates) respectively on the left & right support of
part #22 (Main Push Tube) in order to adjust the height of plow (see the main diagram
for reference).
7. Install the 2 pcs part #2 (Leveling skid plates) respectively on the left & right end of snow
plow, use 2 pcs #3 (nuts 12mm x 1.75mm) to secure them to the plow and to allow the
height of the plow to be adjusted (see the main diagram for reference).
8. Use 2 of the #4 (Bolt 12mm x 37mm x 1.75mm), 2 of the #5 (Washer 12.7mm x 49mm
x 5mm), and 2 of the #6 (Washer 12.7mm x 36mm x5mm) to connect the #21 (Swivel
Plate) bracket with snow plow. Notice the order of the washers and tighten (see the main
diagram for reference).
9. Install the 2 pcs part #8 (Spring Hook) on the snow plow. See the main diagram and
the final assembly photo for reference. Use 2 pcs part #9 (Spring) to connect the bracket
with snow plow.
10. Note: The 400, 500 and 700 UTV’s use the same mounting plate. However, the 500 and
700 have built-in nuts welded on the other side of the front plate.
11. Use 2 pcs #25 (Bolt 10mm x 40mm), 2 pcs #26 (Split Washer 10mm), and #27 (Washer
10mm) to attach the #23 (Bracket Mounting Plate) to the front plate of the frame.
12. On the 400 you will have to reach behind the front plate and hold the nut in place while
the mounting bracket is being attached to the UTV. Again the 500 and 700 have the nuts
welded on the other side of the front plate (see the photos for both).
13. Now it is easy to drive up the snow plow, aligned the snow plow mounting holes with
the holes in the #23 (Bracket Mounting Plate) and use the #24 (Wire Lock Pins) to secure
the plow to the Mounting Plate.
/
