Please read the entire instruction manual before beginning
YOU MAY NEED
1
Hex Wrench
Thin Sink
Mounting
Support
4
Turn off water supply valves and relieve pressure!
Pry off plug button using a small flathead screwdriver.
Unscrew set screw using Hex Wrench.
Remove handle.
Remove handle.
Unscrew dome cap counter clockwise by hand.
Unscrew retaining nut using adjustable wrench.
Remove cartridge assembly and inspect seals.
Contact Giagni for any parts needed or re-assemble parts
by reversing steps.
Handle Removal Maintenance
Valve Cartridge Removal Maintenance
PACKING LIST
Sprayer
Faucet
Body
Giagni warrants to the initial consumer purchaser of this product to be free from defects in material and
workmanship during normal residential use for a lifetime. This warranty do not cover normal wear and tear
or damage to the surface caused by the use of chemicals or chlorides. Damage caused by accident,
misuse, abuse, or practices not in compliance with the care guide included with the product is not covered
by this warranty.
If any defects develop under warranty from the date of purchase, Giagni will replace the product or
defective components. Improper use or installation will immediately void this warranty. No other liability or
obligation is to be assumed. Proof of purchase (original sales receipt) from an authorized Giagni reseller
must be provided to Giagni for all warranty claims. Giagni will not be responsible for shipping charges,
labor charges, installation or any other consequential costs. In no event shall the responsibility of Giagni
exceed the purchase price of the product.
Care
Warranty
GF-183A Series Kitchen Faucet
Rubber Washer
Metal Washer
Mounting Nut
O-Ring
Giagni, Inc
Mount Vernon, NY
1-888-560-5222
www.giagni.com
1. Clean the faucet regularly with clear water or mild liquid soap, rinse the faucet with clear water then
dry with a soft cotton cloth.
2. Do not use any abrasive cleansers, polishes, cloths, scouring pads or paper towels.
3. Do not use any acidic detergents.
3
Flush the lines of air and debris by moving the handle to
the open position and running the water in both the hot
and cold positions for about a minute. This keeps that debris
from clogging the sprayer.
Be sure the hot and cold settings are properly operating.
If they are switched, switch the supply line connections to
the supply valves.
Replace the sprayer and rubber washer. See that the
sprayer is operating in both modes. The sprayer should reset
to aerator mode after the faucet is shut off.
Check for leaks, both in the on and off positions.
8
INSTALLATION PROCEDURES
Turn off the water supply valves
If you are replacing an existing faucet, remove the faucet
from the sink and clean the sink surface thoroughly.
Make sure the O-Ring is placed onto the bottom of
Base Ring before installing.
Install faucet through the desired hole in the sink and/or
countertop.
Position faucet as desired and tighten the Mounting Nut.
Connect hot and cold water supply lines to your water
supply valves. The supply lines are marked accordingly.
2
1
2
4
6
Close
Open
Hot
Cold
Remove the Sprayer from the hose. Be sure to find and put
aside the rubber washer that seals it to the hose.
Keep the hose docked in the arm
Rotate the handle to the closed position.
NOTE: For mounting directly onto thin sinks, a Thin Sink
Mounting Support is supplied to help stabilize the faucet.
If used, it is the first item to go onto the faucet from below.
Do not use for thicker sinks or when mounting faucet to a
countertop.
From underside of sink, attach the mounting hardware
to the faucet body in this order:
1. Thin Sink Mounting Support (optional)
2. Rubber Washer
3. Metal Washer
4. Mounting Nut
3
O-Ring
Thin Sink
Mounting Support
(Flat side up)
Optional
Turn on the water supply valves.
7
Closed
Open
5
/
