KRAUS Oletto™ Single Handle Kitchen Faucet KPF-2631 User manual

Brand: KRAUS

Model: Oletto™ Single Handle Kitchen Faucet KPF-2631

Type: User manual

Single Handle Kitchen Faucet

KPF-2631

INSTALLATION GUIDE

Oletto

™

Congratulations on the purchase of your new

Please keep the box and packaging materials until your product is

completely installed. If you have any questions, require technical

assistance, or have any problems with your product:

Please contact our Customer Service Team

1-800-775-0703 / customerservice@kraususa.com

Have the model number available, and retain a copy of your receipt

with purchase date for reference.

If for any reason this product does not meet your expectations,

please be sure to repack this product in the original box and

packaging material to avoid damage during transit.

DO NOT RETURN TO STORE

Prior to Installation:

•

Make sure you have all necessary parts by checking the diagram and parts list. If

any part is missing or damaged, please contact Kraus Customer Service at 800-775-

0703 for a replacement

•

Pre-drilled countertop hole size requirement: 1-3/8”(min)

• Max countertop thickness: 2-1/8”

Tools you will need:

Wrench Phillips Screwdriver

Safety Goggles

Silicone Sealant

(optional)

Pipe Tape

Turn o the hot and cold water lines at the angle stops and turn on the old faucet

to release any built-up pressure

A. Sprayer

C. Escutcheon

D. Gasket

Diagram and Parts List

F. Weight

G. Weight Clip

B. Faucet Body

E. Easy Install Assembly

H. Quick Connector

I. 2.5mm Hex Wrench

J. 6mm Hex Wrench

Faucet Dimension

Installer Tip:

10 1/4"

[259mm]

21 7/8"

[555mm]

2 1/8"

[54.1mm]

11"

[279.6mm]

9 1/8"

[233.2mm]

8 1/2"

[215.4mm]

2 1/2"

[62mm]

10 3/4"

[274.6mm]

8 1/4"

[209.5mm]

[52mm]

21 5/8"

[549mm]

3/8”-compression

Step 1a: Installing the easy install assembly (Without escutcheon)

Shut o the water supply. Remove the old

faucet. Clean the mounting surface. Check

for the proper thickness of the sink.

Insert the base (a) into sink. If your model

does have a escutcheon, skip to step 1 b.

Step 1b: Installing the easy install assembly (With escutcheon)

Place the escutcheon (C) and the gasket (D)

on the sink. Insert the base (a) into

escutcheon (C). Note: “Front” on the base (a)

must face the front of the sink. The two

mounting plates (b) on the base (a) must be

loose and movable during the installation of

the base (a). If the sink is uneven, use silicone

under the gasket (D).

NOTE: “Front” on the base (a) must face the

front of the sink. The two mounting plates (b)

on the base (a) must be loose and movable

during the installation of the base (a).

Step 2: Installing the easy install assembly

Fig 1 Fig 2

Press the base (a) and escutcheon (C) so that they can not move, then turn the

screws with the provided hex wrench (J, HEX: 6.0mm) clockwise, as shown Fig 1.

When the mounting plates (b) make contact with the sink (1), continue to turn

the screw with the provided hex wrench (J, HEX: 6.0mm) clockwise, as shown

Fig 2, until the base (a) is completely tightened and secured, as shown Fig.4.

Fig 3

Fig 4

Step 3: Installing the faucet

Insert the hose (1) supply lines (2) and quick connect hose (3) one by one

through the hole of the base (a). Carefully insert the hoses into the base.

Place the faucet assembly onto the base (a) as shown in the above gure.

Secure the faucet assembly (B) by tightening the set screw with the provided

hex wrench (I, Hex: 2.5 mm).

Step 4: Securing the faucet assembly

Install the weight clip (G) at the point of

the hose marking "weight here". Insert

the weight (F) onto the weight clip (G)

by sliding it down onto the weight clip (G).

Step 5: Connect waterlines to main valve

Attach waterlines to angle stops

and tighten until snug. Turn on angles

stops and check for leaks (DO NOT TURN

FAUCET ON)

Weight

here

Weight

here

NOTE

are installed before connecting to

the main valve

Step 6: Flush faucet

Pull the hose assembly out of the spout and

remove the sprayer (A) by unscrewing it

from the hose in a counterclockwise direction.

Be sure to hold the end of the hose down into

the sink and turn the faucet on to the warm

position where it mixes hot and cold water.

Flush the water lines for one minute. This

ushes away any debris that could cause

damage to internal parts. Check for leaks.

Re-tighten any connections if necessary, but

do not overtighten. Reinstall the sprayer (A)

by hand tightening it back onto the sprayer

hose.

After installation is completed, turn on the

hot and cold water supplies. Check for leaks.

NOTE: Please make sure washer is

installed attaching sprayer to hose.

Replacement Parts

1. Sprayer

Replacement Parts List Part #

2. Washer

3. Sprayer Hose

5. Inverter

6. O-ring

7. Inverter

9. Bonnet Nut

10. Cap

11. Handle

Finish / Color

KP27254

KP27255

KP27256

KP27257

KP27258

KP27259

KP27250

KP27251

KP27252

8. Cartridge

4. Spring Assembly

KP27253

12. Screw

KP27260

KP27001

13. Index KP27002

*Denotes faucet component color options:

Gray hose with Chrome connector (GRCH) ; Gray hose with Spot-Free Stainless connector (GRSFS);

Black hose w/ Matte Black connector (BLMB); Black hose with Spot-Free Antique Champagne Bronze (BLSFACB);

Black hose with Brushed Brass (BLBB);

CH- Polished Chrome ; SFS - Spot Free Stainless Steel ; MB - Matte Black; BB - Brushed Brass;

SFACB - Spot Free Antique Champagne BronzeGR - GreyBL - Black

14. Escutcheon

15. Block

KP27261

16. O-ring

KP27073

KP27092

17. Easy Install Assembly

18. Filter Washer

KP27262

19. Weight & Clip Assembly

KP27167

KP27236

20. Hex Wrench

21. Hex Wrench

KP27020

KP27263

WHITE

22. 1.8GPM Flow Restrictor

KP27074-WH

23. Quick Connector

Assembly

KP27090

GR, BL*

BB, CH, SFS, MB,

SFACB*

BB, CH, SFS, MB,

SFACB*

BLBB, GRCH,

GRSFS, BLMB,

BLSFACB*

GR, BL*

BB, CH, SFS, MB,

SFACB*

BB, CH, SFS, MB,

SFACB*

BB, CH, SFS, MB,

SFACB*

Troubleshooting

If you have followed the instructions carefully and your faucet still does not work

properly, take the following coorective steps:

Care & Maintenance

*To keep the product clean & shining, follow the steps below

1. Rinse with clean water & dry with a soft cloth

2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners

3. Do not use cloth with a coarse surface

4. Unscrew the aerator and clean when necessary

*This installation manual is subject to change without further notice.

Hexagon Nut

Hot

Water

Cold

Water

Open

Left

Hot Water

Push

25˚

90˚

PROBLEM CAUSE ACTION

Leakage under the

handle

Bonnet nut (9) has

come loose

Remove the index (13).

Loosen screw (12) with hex

wrench (20). Remove the

handle (11) and cap (10).

Tighten bonnet nut (9) with an

adjustable wrench

The aerator has an

irregular or reduced

water ow

The aerator is dirty or

mis-tted

Remove the aerator and

check for debris.

Ensure that the rubber

washer is properly installed

Water will not shut o

completely

Cartridge may need to

be adjusted or replaced

Remove the index (13).

Loosen screw (12) with hex

wrench (20). Remove the

handle (11) and cap (10).

Tighten bonnet nut (9) with an

adjustable wrench. Remove the

cartridge (8). Check for cracks

There is leaking from the

sink drain at the base of

the sink.

The sink has a rough or

irregular surface.

Apply additional silicone

sealant to the beveled side of

the drain ange. Retighten

and test for leaks

There is a low ow of

water.

The lter washer in the

hose connectors is dirty.

Turn o the water supply at

water valve and unscrew the

hose connectors from water

supply lines. Clean the lter

washer in the water lines with

hot water, removing any debris

or calcium build up

Codes/Standards Applicable:

Faucet Warranty

Restrictions

This warranty does not cover antediluvian, discontinued, or display products, whether such items are purchased at

discount outlets, unauthorized dealers, and/or sold on clearance.

This warranty does not cover instances of negligence, misuse, abuse, improper installation, carelessness, accident, hard

water or mineral deposits, exposure to corrosive materials, misapplication, damages caused by improper maintenance,

alteration of the product, or failure to follow care or installation instructions enclosed with your product. Avoid using

abrasive cleaners such as powders, bleach, ammonia, alcohol, or chlorine. Avoid using abrasive pads, steel wool, or wire

brushes, as these will damage and wear down the ﬁnish.

This warranty does not apply to Products that have not been installed or operated in accordance with instructions

supplied by Kraus and all applicable rules, regulations, and legislation pertaining to such installations.

This warranty does not apply unless the Kraus product is installed by a fully insured and licensed trade professional.

Kraus insists that such professionals have experience in the installation of bathroom and kitchen manufactured goods.

This warranty does not cover labor charges or costs of removal and reinstallation of said product. This warranty does

not allow recovery of incidental or consequential damages, such as loss of use, delay, property damage, or other

consequential damages, and Kraus accepts no liability for such damages.

This warranty does not cover Marine or Outdoor Installation.

Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of

merchantability and ﬁtness for a particular purpose, or compliance with any code.

NSF/ANSI 372

NSF/A N SI 61

ASME A112.18.1

1.8GPM 6.8L/min maximum

LEAD FREE

Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”).

Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location.

The warranty is non-transferable.

Kraus warrants the structure and ﬁnish of the product to be free from defects in material and workmanship under

normal usage for the lifetime of the product. The warranty commences from the initial date of purchase by the owner or

trade professional, from an authorized Kraus dealer, through the lifetime of the original owner or end-user.

Kraus warrants the mechanical components such as but not limited to sprayhead assembly (includes engine, aerators,

structure, restrictors, back ﬂow preventers, sprayer hoses, braided supply line hoses which encompasses nylon,silicon

and stainless steel, etc) of the product to be free from defects in material and workmanship under normal usage for a

period of one (1) year. The warranty commences from the initial date of purchase by the owner or trade professional,

from an authorized Kraus dealer, through the one (1) year term of the original owner or end-user.

Kraus warrants the mechanical component (cartridge) of the product to be free from defects in material and

workmanship under normal usage for a period of ﬁve (5) years. The warranty commences from the initial date of

purchase by the owner or trade professional, from an authorized Kraus dealer, through the ﬁve (5) year term of the

original owner or end-user.

Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be

repaired or replaced with a product of equal value at the option of Kraus. This warranty extends to the original owner or

end-user, and is not transferable to a subsequent owner.

Kraus warrants all electronic parts other than batteries to be free from defects in material and workmanship for a

period of two (2) years. The warranty commences from the initial date of purchase by the owner or trade professional,

from an authorized Kraus dealer, through the two (2) year term of the original owner or end-user. No warranty is provided

on batteries.

If you are a homeowner please contact a Kraus Customer Service Representative at:

Kraus USA, Inc.

12 Harbor Park Drive

Port Washington, NY 11050

Toll-free 800-775-0703

[email protected]

If you are a plumbing contractor or trade professional please contact a Kraus

Pro Representative at:

If you are an Authorized Partner please contact a Partner Support Representative at:

In requesting warranty service, please be ready to provide:

1. Proof of purchase.

2. A description of the problem.

Download the Kraus Care & Maintenance Guide at:

http://www.kraususa.com/maintenance

Commercial Warranty

Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and

business use.

Shipping charges will be covered foe the ﬁrst (1) year of the warranted replacement part or product (HI, AK, and Puerto

Rico shipping charges may apply). International shipping fees are not included.

All incidental or consequential damages are speciﬁcally excluded. No additional warranties, express or implied, are

given, including but not limited to any implied warranty of merchantability or ﬁtness for a particular purpose.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long

an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you speciﬁc

legal rights, and you may also have other rights which vary from state to state.

Kraus USA, Inc.

12 Harbor Park Drive

Port Washington, NY 11050

516-801-8955

[email protected]

Kraus USA, Inc.

12 Harbor Park Drive

Port Washington, NY 11050

516-801-8954

[email protected]

IMPORTANT

http://www.kraususa.com/registration

Activate Your Warranty

Access Premium Customer Support

Get Product Information

www.kraususa.com

KRAUS Oletto™ Single Handle Kitchen Faucet KPF-2631 User manual

KRAUS Oletto™ Single Handle Kitchen Faucet KPF-2631 User manual

KRAUS Oletto™ Single Handle Kitchen Faucet KPF-2631 User manual

Related papers

Other documents