Giagni 813G BN Installation guide

Brand
Giagni
Model
813G BN
Category
Faucets
Type
Installation guide
1
4
Handle Removal Maintenance Valve Cartridge Removal Maintenance
Please read the entire instruction manual before beginning
YOU MAY NEED
PACKING LIST
GF-183N Series Kitchen Faucet
Hex Wrench
Thin Sink
Mounting
Support
Sprayer
Faucet
Body
Rubber Washer
Metal Washer
Mounting Nut
O-Ring
Giagni warrants to the initial consumer purchaser of this product to be free from defects in material and
workmanship during normal residential use for a lifetime. This warranty do not cover normal wear and tear
or damage to the surface caused by the use of chemicals or chlorides. Damage caused by accident,
misuse, abuse, or practices not in compliance with the care guide included with the product is not covered
by this warranty.
If any defects develop under warranty from the date of purchase, Giagni will replace the product or
defective components. Improper use or installation will immediately void this warranty. No other liability or
obligation is to be assumed. Proof of purchase (original sales receipt) from an authorized Giagni reseller
must be provided to Giagni for all warranty claims. Giagni will not be responsible for shipping charges,
labor charges, installation or any other consequential costs. In no event shall the responsibility of Giagni
exceed the purchase price of the product.
Care
Warranty
Giagni, Inc
Mount Vernon, NY
1-888-560-5222
[email protected]
www.giagni.com
1. Clean the faucet regularly with clear water or mild liquid soap, rinse the faucet with clear water then
dry with a soft cotton cloth.
2. Do not use any abrasive cleansers, polishes, cloths, scouring pads or paper towels.
3. Do not use any acidic detergents.
Turn off water supply valves and relieve pressure!
Pry off plug button using a small flathead screwdriver.
Unscrew set screw using Hex Wrench.
Remove handle.
Remove handle.
Unscrew dome cap counter clockwise by hand.
Unscrew retaining nut using adjustable wrench.
Remove cartridge assembly and inspect seals.
Contact Giagni for any parts needed or re-assemble parts
by reversing steps.
Washer
8
3
Closed
Open
Hot
Cold
INSTALLATION PROCEDURES
Turn off the water supply valves
If you are replacing an existing faucet, remove the faucet
from the sink and clean the sink surface thoroughly.
Make sure the O-Ring is placed onto the bottom of
Base Ring before installing.
Install faucet through the desired hole in the sink and/or
countertop.
Position faucet as desired and tighten the Mounting Nut.
2
1
2
4
NOTE: For mounting directly onto thin sinks, a Thin Sink
Mounting Support is supplied to help stabilize the faucet.
If used, it is the first item to go onto the faucet from below.
Do not use for thicker sinks or when mounting faucet to a
countertop.
From underside of sink, attach the mounting hardware
to the faucet body in this order:
1. Thin Sink Mounting Support (optional)
2. Rubber Washer
3. Metal Washer
4. Mounting Nut
3
O-Ring
Thin Sink
Mounting Support
(Flat side up)
Optional
Flush the lines of air and debris by moving the both handles to
the open position and running the water in both the hot
and cold positions for about a minute. This keeps debris
from clogging the aerator and sprayer.
Be sure the hot and cold settings are properly operating.
If they are switched, switch the supply line connections to
the supply valves.
Replace the Sprayer and rubber washer.
Replace the Aerator and rubber washer.
See that the sprayer is operating in both modes.
Check for leaks, both in the on and off positions.
Connect hot and cold water supply lines to your water
supply valves. The supply lines are marked accordingly.
Remove the Sprayer from the hose. Be sure to find and put
aside the rubber washer that seals it to the hose.
Remove the Aerator from the spout. Be sure to find and put
aside the rubber washer that seals it to the spout.
Keep the hose docked in the arm
Rotate the faucet handle to the closed position.
Turn on the water supply valves.
7
6
5
Closed
Open
Sprayer
Aerator
Washer
Washer
Closed
Open
  • Page 1 1
  • Page 2 2

Giagni 813G BN Installation guide

Brand
Giagni
Model
813G BN
Category
Faucets
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents