Foundry Networks 2402CF User manual

Brand: Foundry Networks

Model: 2402CF

Category: Network switches

Type: User manual

This manual is also suitable for

EdgeIron 2402CF

Foundry EdgeIron 2402CF

Installation Guide

2100 Gold Street

P.O. Box 649100

San Jose, CA 95164-9100

Tel 408.586.1700

Fax 408.586.1900

www.foundrynetworks.com

February 2003

No part of this work may be reproduced in any form or by any

means – graphic, electronic or mechanical, including

photocopying, recording, taping or storage in an information

retrieval system – without prior written permission of the copyright

owner.

The trademarks, logos and service marks ("Marks") displayed

herein are the property of Foundry or other third parties. You are

not permitted to use these Marks without the prior written consent

of Foundry or such appropriate third party.

Foundry Networks, BigIron, FastIron, IronView, JetCore, NetIron,

ServerIron, Turb o I r on, IronWare, EdgeIron, the Iron family of

marks and the Foundry Logo are trademarks or registered

trademarks of Foundry Networks, Inc. in the United States and

other countries.

F-Secure is a trademark of F-Secure Corporation. All other

trademarks mentioned in this document are the property of their

respective owners.

)HEUXDU\ )RXQGU\1HWZRUNV,QF L

COMPLIANCES

FCC - Class A

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

interference to radio communications. It has been tested and found to comply

with the limits for a Class A computing device pursuant to Subpart B of Part 15 of

FCC Rules, which are designed to provide reasonable protection against such

interference when operated in a commercial environment. Operation of this

equipment in a residential area is likely to cause interference, in which case the

user, at his own expense, will be required to take whatever measures may be

required to correct the interference. You are cautioned that changes or

modifications not expressly approved by the party responsible for compliance

could void your authority to operate the equipment.

You may use unshielded twisted-pair (UTP) cable for RJ-45

connections—Category 3 or greater for 10 Mbps connections, Category 5 for 100

Mbps connections and Category 5 or 5e for 1000 Mbps connections. Use 50/125 or

62.5/125 micron multimode fiber optic cable, or 9/125 micron single-mode cable,

for SFP transceiver connections.

Warnings: 1. Wear an anti-static wrist strap or take other suitable measures to

prevent electrostatic discharge when handling this equipment.

2. When connecting this switch to a power outlet, connect the field

ground lead on the tri-pole power plug to a valid earth ground

line to prevent electrical hazards.

EC Conformance Declaration - Class A

Contact Foundry Networks at:

Foundry Networks Inc.

2100 Gold Street

P.O. Box 649100

San Jose, CA 95164-9100

This information technology equipment complies with the requirements of the

Council Directive 89/336/EEC on the Approximation of the laws of the Member

States relating to Electromagnetic Compatibility and 73/23/EEC for electrical

equipment used within certain voltage limits and the Amendment Directive 93/

LL )RXQGU\1HWZRUNV,QF )HEUXDU\

68/EEC. For the evaluation of the compliance with these Directives, the following

standards were applied:

Warning: Do not plug a phone jack connector in the RJ-45 port. This may damage

this device. Les raccordeurs ne sont pas utilisé pour le systéme téléphonique!

RFI Emission: • Limit class A according to EN 55022:1998

• Limit class A for harmonic current emission according to

EN 61000-3-2/1995

• Limitation of voltage fluctuation and flicker in low-voltage

supply system according to EN 61000-3-3/1995

Immunity: • Product family standard according to EN 55024:1998

• Electrostatic Discharge according to EN 61000-4-2:1995

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

• Radio-frequency electromagnetic field according to

EN 61000-4-3:1996 (80 - 1000 MHz with 1 kHz AM 80%

Modulation: 3 V/m)

• Electrical fast transient/burst according to EN 61000-4-4:1995

(AC/DC power supply: ±1 kV, Data/Signal lines: ±0.5 kV)

• Surge immunity test according to EN 61000-4-5:1995

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

• Immunity to conducted disturbances, Induced by

radio-frequency fields: EN 61000-4-6:1996 (0.15 - 80 MHz with

1 kHz AM 80% Modulation: 3 V/m)

• Power frequency magnetic field immunity test according to

EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)

• Voltage dips, short interruptions and voltage variations

immunity test according to EN 61000-4-11:1994 (>95%

Reduction @10 ms, 30% Reduction @500 ms, >95% Reduction

@5000 ms)

LVD: • EN 60950 (A1/1992; A2/1993; A3/1993; A4/1995; A11/1997)

)HEUXDU\ )RXQGU\1HWZRUNV,QF LLL

Industry Canada - Class A

This digital apparatus does not exceed the Class A limits for radio noise emissions

from digital apparatus as set out in the interference-causing equipment standard

entitled “Digital Apparatus,” ICES-003 of the Department of Communications.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables

aux appareils numériques de Classe A prescrites dans la norme sur le matériel

brouilleur: “Appareils Numériques,” NMB-003 édictée par le ministère des

Communications.

Japan VCCI Class A

7DLZDQ%60,&ODVV$

Australia AS/NZS 3548 (1995) - Class A

Contact Foundry Networks at:

Foundry Networks Inc.

2100 Gold Street

P.O. Box 649100

San Jose, CA 95164-9100

ACN 066 352 010

LY )RXQGU\1HWZRUNV,QF )HEUXDU\

Safety Compliance

Warning: Fiber Optic Port Safety

Avertissment: Ports pour fibres optiques - sécurité sur le plan

optique

Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit

Underwriters Laboratories Compliance Statement

Important! Before making connections, make sure you have the correct cord set.

Check it (read the label on the cable) against the following:

When using a fiber optic port, never look at the

transmit laser while it is powered on. Also, never

look directly at the fiber TX port and fiber cable

ends when they are powered on.

Ne regardez jamais le laser tant qu’il est sous

tension. Ne regardez jamais directement le port TX

(Transmission) à fibres optiques et les embouts de

câbles à fibres optiques tant qu’ils sont sous tension.

Niemals ein Übertragungslaser betrachten,

während dieses eingeschaltet ist. Niemals direkt auf

den Faser-TX-Anschluß und auf die

Faserkabelenden schauen, während diese

eingeschaltet sind.

120 Volts UL Listed/CSA Certified Cord Set

Minimum 18 AWG

Type SVT or SJT three conductor cord

Maximum length of 15 feet

Parallel blade, grounding type attachment

plug rated 15 A, 125 V

240 Volts (Europe

only)

Cord Set with H05VV-F cord having three

conductors with minimum diameter of 0.75

IEC-320 receptacle

Male plug rated 10 A, 250 V

CLASS I

LASER DEVICE

DISPOSITIF LASER

DE CLASSE I

LASERGER

DER KLASSE I

ÄT

)HEUXDU\ )RXQGU\1HWZRUNV,QF Y

The unit automatically matches the connected input voltage. Therefore, no

additional adjustments are necessary when connecting it to any input voltage

within the range marked on the rear panel.

Wichtige Sicherheitshinweise (Germany)

1. Bitte lesen Sie diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie

keine Flüssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes

Tuch zur Reinigung.

4. Die Netzanschlu ßsteckdose soll nahe dem Gerät angebracht und leicht

zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen

oder Fallen könnte Beschädigungen hervorrufen.

7. Die Belüftungsöffnungen dienen der Luftzirkulation, die das Gerät vor

Überhitzung schützt. Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt

werden.

8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.

9. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es

sollte auch nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.

11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom

Stromnetz trennen. Somit wird im Falle einer Überspannung eine

Beschädigung vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten

in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag

auslösen.

13. Öffnen sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen

Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen

und von einer qualifizierten Servicestelle zu überprüfen:

a. Netzkabel oder Netzstecker sind beschädigt.

b. Flüssigkeit ist in das Gerät eingedrungen.

c. Das Gerät war Feuchtigkeit ausgesetzt.

d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert

oder Sie mit

Hilfe dieser Anleitung keine Verbesserung erzielen.

e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

YL )RXQGU\1HWZRUNV,QF )HEUXDU\

15. Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden.

Für einen Nennstrom bis 6 A und einem Gerätegewicht größer 3 kg ist eine

Leitung nicht leichter als H05VV-F, 3G, 0.75 mm

einzusetzen.

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70

dB(A) oder weniger.

)HEUXDU\ )RXQGU\1HWZRUNV,QF YLL

Contents

Chapter 1

About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

How to Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Foundry Networks Technical Support . . . . . . . . . . . . . . . 1-2

Web Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

E-mail Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Telephone Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Warranty Coverage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Chapter 2

About the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Switch Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Management Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Description of Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

RJ-45 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Port Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Power Supply Receptacle . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Chapter 3

Network Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Introduction to Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Application Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Connectivity Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

YLLL )RXQGU\1HWZRUNV,QF )HEUXDU\

1000 Mbps Gigabit Ethernet Collision Domain . . . . . . . .3-2

Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

Chapter 4

Installing the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Selecting a Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Equipment Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

Optional Rack-Mounting Equipment . . . . . . . . . . . . . . . .4-2

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

Desktop or Shelf Mounting . . . . . . . . . . . . . . . . . . . . . . . . .4-4

Connecting to a Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

Chapter 5

Making Network

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Connecting Network Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Twisted-Pair Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Cabling Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Connecting to PCs, Servers, Hubs and Switches . . . . . . .5-2

Wiring Closet Connections . . . . . . . . . . . . . . . . . . . . . . . . .5-3

Fiber Optic Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5

Appendix A

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Diagnosing Switch Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Power and Cooling Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

In-Band Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Appendix B

Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1

Twisted-Pair Cable and Pin Assignments . . . . . . . . . . . . . . . . . B-2

10BASE-T/100BASE-TX Pin Assignments . . . . . . . . . . . B-2

Straight-Through Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . B-4

Crossover Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4

)HEUXDU\ )RXQGU\1HWZRUNV,QF L[

1000BASE-T Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5

1000BASE-T Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . B-6

Cable Testing for Existing Category 5 Cable . . . . . . . . . . B-6

Adjusting Existing Category 5 Cabling . . . . . . . . . . . . . . B-6

Console Port Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7

DB-9 Port Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . B-7

Console Port to 9-Pin DTE Port on PC . . . . . . . . . . . . . . . B-7

Console to 25-Pin DTE Port on PC . . . . . . . . . . . . . . . . . . B-8

Appendix C

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Base Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1

Management Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3

Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4

CE Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4

Glossary

Index

[ )RXQGU\1HWZRUNV,QF )HEUXDU\

CHAPTER 1

ABOUT THIS GUIDE

Audience

This guide is for system administrators with a working

knowledge of network management.

You should be familiar with switching and networking concepts.

Nomenclature

This guide uses the following typographical conventions to show

information:

Italichighlights the title of another publication and occasionally

emphasizes a word or phrase.

codeshows text that must be entered exactly as it appears in this

guide.

1RWH emphasizes an important fact or calls your attention to a

dependency.

How to Get Help

If you need assistance, Foundry Networks is committed to

ensuring that your investment in our products remains

cost-effective by offering a variety of support options.

BOUT

HIS

UIDE

Foundry Networks Technical Support

Foundry Networks technical support will ensure that the fast and

easy access that you have come to expect from your Foundry

Networks products will be maintained.

Web Access

Point your browser to the following URL:

http://www.foundrynetworks.com.

Navigate to Services/Technical Support.

Click the Login button, then enter your user name and password

to gain access to the Foundry support site.

E-mail Access

Technical requests can also be sent to the e-mail address:

VXSSRUW#IRXQGU\QHWFRP

Telephone Access

◆ 785%2&$//8QLWHG6WDWHV

◆ 2XWVLGHWKH8QLWHG6WDWHV

Warranty Coverage

Contact Foundry Networks using any of the methods listed

above for information about the standard and extended

warranties.

Related Publications

Refer to the Foundry EdgeIron User Guide for instructions on how

to configure and manage the switch.

CHAPTER 2

ABOUT THE SWITCH

Overview

This switch is an ideal solution for delivering Internet access to

individual users in multi-dwelling or multi-tenant units (MDUs/

MTUs), such as apartment housing blocks, commercial buildings

or hotels. This switch provides rate-limitable connections to

individual users with secure port-to-port isolation between users

– all with conventional Ethernet cabling and adapters. At an

MDU/MTU site, up to 24 other switches can be cascaded from

one switch, providing broadband Internet access for up to 24

individual users on each switch.

Figure 2-1. Front and Rear Panels

Media Slots

Combo Gigabit

Ethernet ports

RJ-45/SF

System Indicators

PWR, Diag, Stack

10/100 Mbps RJ-45 Ports

Port Status Indicators (1-24)

On Amber: 10 Mbps link

Flashing Amber: 10 Mbps link/activity

On Green: 100 Mbps link

Flashing Green: 100 Mbps link/activity

Console Port

Use this port for console connection

Module Status Indicators (25/26)

On Amber: 10/100 Mbps link

Flashing Amber 10/100 Mbps link/activity

On Green: 1000 Mbps link

Flashing Green: 1000 Mbps link/activity

100-240V~

50/60Hz, 2A

Power Socket

BOUT

THE

WI TCH

Switch Architecture

The switch contains 24 10/100 Mbps Fast Ethernet ports on the

front panel. Each port can provide a dedicated link directly to an

end-user PC, or be attached to another Ethernet switch/hub at

the end-user’s premises and used as a shared link. The switch

completely eliminates the bottlenecks of dial-up internet access

by offering a configurable bandwidth of up to 100 Mbps full

duplex for each end-user connection. For all port connections, the

switch’s 8.8 Gbps bandwidth capacity is more than enough to

handle even the most demanding environments.

Auto-negotiation is used to select the optimal transmission speed

and communication mode for each connection. With

store-and-forward switching and flow control, maximum data

integrity is always maintained, even under heavy loading.

This switch includes two port: 1000BASE-SX and RJ-45. These

ports allow users the flexibility to use either fiber or copper

media.

The switch also supports a stacking module that can be installed

into slot M1. The stacking module allows up to eight units to be

linked together and managed from one unit using one IP address.

Management Options

This switch contains a comprehensive array of LEDs for

“at-a-glance” monitoring of network and port status. It also

includes a management agent that allows you to configure or

monitor the switch using its embedded management software, or

via SNMP applications. To manage the switch, you can make a

direct connection to the RS-232 console port (out-of-band), or you

can manage the switch through a network connection (in-band)

using Telnet, the on-board Web agent, or Windows-based

network management software.

VER VI E W

The management agent provides a wide range of advanced

performance-enhancing features. Port-based VLANs provide

traffic security and efficient use of network bandwidth. QoS

priority queueing ensures the minimum delay for

mo v in g

real-time multimedia data through the switch. Flow control

eliminates the loss of packets due to bottlenecks caused by port

saturation. Port security is provided to filter unwanted traffic

from the switch.

Some of the switch’s advanced features are described below. For

a detailed description, refer to the Foundry EdgeIron User Guide.

VLANs

This switch supports up to 255 VLANs. A Virtual LAN is a

collection of network nodes that share the same collision domain

regardless of their physical location or connection point in the

network. By segmenting your network into VLANs, you can:

• Eliminate broadcast storms which severely degrade

performance in a flat network.

• Simplify network management for node changes/moves by

remotely configuring VLAN membership for any port, rather

than having to manually change the node’s physical

connection.

• Provide data security by restricting all traffic to the

originating VLAN, except where a connection is explicitly

defined via the switch’s routing service.

This switch supports Private VLANs as an extension of the

common VLAN. Private VLANs can be used to provide

port-based security and isolation between ports within a VLAN.

Private VLANs deliver per port security, requiring only one

VLAN on every switch, not every port. This feature greatly

BOUT

THE

WI TCH

minimizes the total number of VLANs required. Private VLANs

and normal VLANs can exist simultaneously in the same switch.

Multicast Switching

Specific multicast traffic can be assigned to its own VLAN to

ensure that it does not interfere with normal network traffic and

to guarantee real-time delivery by setting the required priority

level for the designated VLAN. The switch uses IGMP Snooping.

Traffic Priority

This switch provides Quality of Service (QoS) by prioritizing

each packet based on the required level of service, using four

distinct categories with Weighted Round Robin queuing. It uses

IEEE 802.1p and 802.1Q tags to prioritize incoming traffic based

on input from the end-station application. These functions can be

used to provide independent priorities for delay-sensitive data

and best-effort data.

Description of Hardware

RJ-45 Ports

The switch base unit contains 24 10BASE-T/100BASE-TX RJ-45

ports. All of these ports support automatic MDI/MDI-X

operation, so you can use straight-through cables for all network

connections to PCs or servers, or to other switches or hubs. (See

“10BASE-T/100BASE-TX Pin Assignments” on page -2.)

Each of these ports support IEEE 802.3x auto-negotiation, so the

optimum transmission mode (half or full duplex), and data rate

(10 or 100 Mbps) can be selected automatically, if this feature is

also supported by the attached device. If a device connected to

one of these ports does not support auto-negotiation, the correct

speed will be sensed by the port, but the transmission mode will

default to half duplex.

ESCRI PTI ON

ARDWARE

Each port also supports auto-negotiation of flow control, so the

switch can automatically prevent port buffers from becoming

saturated.

Port Status LEDs

The base unit also includes a display panel for key system and

port indications that simplify installation and network

troubleshooting. The LEDs, which are located on the front panel

for easy viewing, are shown below and described in the

following tables.

Figure 2-2. Port Status LEDs

Port Status LEDs

LED Condition Status

Base Unit Ports

1~24

(Link/

Activity)

On/Flashing

Amber

Port has established a valid 10 Mbps

network connection. Flashing indicates

activity.

On/Flashing

Green

Port has established a valid 100 Mbps

network connection. Flashing indicates

activity.

Off There is no valid link on the port.

BOUT

THE

WI TCH

Figure 2-3. System Status LEDs

Module Ports

25, 26

(Link/

Activity)

On/Flashing

Amber

Port has established a valid 10/100

Mbps network connection. Flashing

indicates activity.

On/Flashing

Green

Port has established a valid 1000 Mbps

network connection. Flashing indicates

activity.

Off There is no valid link on the port.

System Status LEDs

LED Condition Status

PWR On Green The unit’s internal power supply is

operating normally.

On Amber The unit’s internal power supply has

failed.

Off The unit has no power connected.

Port Status LEDs

LED Condition Status

Page is loading ...

Foundry Networks 2402CF User manual

Brand: Foundry Networks

Model: 2402CF

Category: Network switches

Type: User manual

This manual is also suitable for

EdgeIron 2402CF

Download PDF

report

Foundry Networks 2402CF User manual

This manual is also suitable for

Foundry Networks 2402CF User manual

Related papers

Other documents