Project
Item No.
Quantity
Model 40GS-KLS - 40 gallon (151 litres) gas short height stationary kettle
CONSTRUCTION
316 stainless steel, one-piece welded construction
Fully jacketed kettle
All exposed surfaces shall be stainless steel
Kettle body is sheathed in stainless steel and air gap insulated.
ASME shop inspected, stamped and registered with the National Board
for operation up to a maximum working pressure of 30 PSI. Unit shall be
UL listed for sale in USA and Canada. Unit shall be registered in Canada
with a CRN number.
Outer sheathing and air insulating gap retains heat and keeps kettle
exterior cooler to the touch.
OPERATION
Gas-heated, self-contained steam source provides temperatures of 150
to 270°F
Gas regulator valve and electronic ignition module
Thermostatically controlled to shut off automatically when desired tem-
perature is reached or on when temperature falls below desired setting
Factory charged with chemically-pure water and rust inhibitors to ensure
long life and minimum maintenance
All controls are front mounted in easy reach of the operator
Regulating thermostat
Pressure gauge
Power on/off switch
Heat, power and lower water indicator lights
Water level sight glass
Pressure safety relief valve
Pressure limit control
Low water cut-off
STANDARD FEATURES
One-piece domed cover with counter balanced spring-assist
Faucet bracket
2” sanitary tangent drawoff
Removable 1/4” perforated stainless steel strainer
One year parts and labor warranty*
* For all international markets, contact your local distributor.
BLODGETT
www.blodgett.com
44 Lakeside Avenue, Burlington, VT 05401 • Phone: (802) 658-6600 • Fax: (802) 864-0183
OPTIONS AND ACCESSORIES
(AT ADDITIONAL CHARGE)
Etched markings
Gallons
Litres
Strainer
1/8” perforated disc strainer
1/4” perforated disk strainer
Solid disc strainer
Basket inserts
Swing faucets
Automatic water filler
3” tangent drawoff
Kettle brush kit
Contour measuring strip
40GS-KLS
Short Height Gas Tri-Leg Stationary Kettle
40GS-KLS SHORT HEIGHT STATIONARY KETTLE
BLODGETT
www.blodgett.com
44 Lakeside Avenue, Burlington, VT 05401 • Phone: (802) 658-6600 • Fax: (802) 864-0183
40GS-KLS TRI-LEG STATIONARY KETTLE
Printed in U.S.A. NOTE: FOR COMMERCIAL USE ONLY
NOTE: The company reserves the right to make substitutions of
components without prior notice.
54.25
(1327)
27.13
(638)
2 (51)
min side
clearance
6 (152) dia
draft diverter
flue outlet
4 (102) rear
clearance
2 (51)
min side
clearance
4.75 (121)
43.25 (1099)
4 (102)
3.75
(171)
TOP VIEW
30.38
(772)
Kettle
Leg Position
30°
NOTES:
1. Dimensions are inches (mm).
2. Minimum distance from combustible
walls: 2 (51) on sides and 4 (102) from
rear. Blodgett recommends 8 (203) on
right side for servicing.
18 (457) flue height
38
(965)
rim height
25
(635)
Faucet
bracket
7 (178)
FRONT VIEW
Adjustable
bullet feet
71.75
(1822)
w/cover
open
21.38
(543)
7.5 (191)
6 (152)
Gas connection
7/8” dia
Electrical connection
9.5
(241)
2 (51)
tangent
draw off
Cover open
(not shown in
other views)
32.38 (822) O.D.
26 (660) I.D.
RIGHT SIDE VIEW
APPROVAL/STAMP
P/N S00146 Rev A (4/11)
SHORT FORM SPECIFICATIONS
Provide Blodgett model 40GS-KLS (40 gallon)short height gas heated, stainless steel, fully steam jacketed kettle. Unit shall include 2” sanitary tangent draw-off valve, and No. 51 spring
assisted cover. Steam jacket is insulated and ASME code constructed for maximum working pressure of 30 PSI. Unit is thermostatically controlled, with electronic ignition as standard.
CSA design certified and NSF listed. Provide options and accessories as indicated.
MAXIMUM INPUT: Natural Gas Propane
40GS-KLS 100,000 BTU 85,000 BTU
GAS SUPPLY:
1/2" NPT connection required. A gas shut-off valve must be installed in
supply piping convenient and adjacent to unit.
Inlet Pressure:
Natural 4.5" W.C. min, 14” W.C. max
Propane 11" W.C. min, 14” W.C. max
ELECTRICAL CONNECTION:
Requires one 115 Volt, single-phase, 60 HZ, 2 AMP supply.
SHIPPING INFORMATION:
Approx. Weight:
40GS-KLS 620 lbs. (281 kg)
/
