ESAB FABRICATOR® 211i 3-IN-1 Multi Process Welding Systems User manual

Brand: ESAB

Model: FABRICATOR® 211i 3-IN-1 Multi Process Welding Systems

Category: Welding System

Type: User manual

This manual is also suitable for

ESAB Fabricator® 211i 3-IN-1 Multi Process Welding Systems

A-12922

210

115V

208/230V

3163339

Révision : AA Issue Date: September 2, 2015 Manual No.: 0-5422

Operating

Manual

ESAB Fabricator

211i

3-IN-1 Multi Process

Welding Systems

esab.com

WE APPRECIATE YOUR BUSINESS!

Congratulations on your new ESAB product. We are proud to have you as our customer and will strive to

provide you with the best service and reliability in the industry. This product is backed by our extensive

warranty and world-wide service network. To locate your nearest distributor or service agency, visit us on

the web at www.esab.com.

This Operating Manual has been designed to instruct you on the correct use and operation of your ESAB

product. Your satisfaction with this product and its safe operation is our ultimate concern. Therefore please

take the time to read the entire manual, especially the Safety Precautions. They will help you to avoid potential

hazards that may exist when working with this product.

YOU ARE IN GOOD COMPANY!

The Brand of Choice for Contractors and Fabricators Worldwide.

ESAB is a Global Brand of manual and automation Plasma Cutting Products.

We distinguish ourselves from our competition through market-leading, dependable products that have stood

the test of time. We pride ourselves on technical innovation, competitive prices, excellent delivery, superior

customer service and technical support, together with excellence in sales and marketing expertise.

Above all, we are committed to developing technologically advanced products to achieve a safer working

environment within the welding industry.

WARNING

Read and understand this entire Manual and your employer’s safety practices before install-

ing, operating, or servicing the equipment.

While the information contained in this Manual represents the Manufacturer's best judgement,

the Manufacturer assumes no liability for its use.

Plasma Cutting Power Supply

ESAB Fabricator

211i 3-in-1 Multi Process Welding Systems™

Operating Manual Number 0-5422

Published by:

ESAB

2800 Airport Rd.

Denton, TX 76208

www.esab.com

Reproduction of this work, in whole or in part, without written permission of the

publisher is prohibited.

The publisher does not assume and hereby disclaims any liability to any party for

any loss or damage caused by any error or omission in this Manual, whether such

error results from negligence, accident, or any other cause.

Original Publication Date: September 2, 2015

Revision Date:

Record the following information for Warranty purposes:

Where Purchased:_______________________________ __________

Purchase Date:__________________________________ __________

Power Supply Serial #:___________________________ __________

Torch Serial #:___________________________________ __________

Be sure this information reaches the operator.

You can get extra copies through your supplier.

CAUTION

These INSTRUCTIONS are for experienced operators. If you are not fully familiar

with the principles of operation and safe practices for arc welding and cutting equip-

ment, we urge you to read our booklet, “Precautions and Safe Practices for Arc

Welding, Cutting, and Gouging,” Form 52-529. Do NOT permit untrained persons to

install, operate, or maintain this equipment. Do NOT attempt to install or operate this

equipment until you have read and fully understand these instructions. If you do not

fully understand these instructions, contact your supplier for further information. Be

sure to read the Safety Precautions before installing or operating this equipment.

USER RESPONSIBILITY

This equipment will perform in conformity with the description thereof contained in this manual and accom-

panying labels and/or inserts when installed, operated, maintained and repaired in accordance with the instructions

provided. This equipment must be checked periodically. Malfunctioning or poorly maintained equipment should not be

used. Parts that are broken, missing, worn, distorted or contaminated should be replaced immediately. Should such re-

pair or replacement become necessary, the manufacturer recommends that a telephone or written request for service

advice be made to the Authorized Distributor from whom it was purchased.

This equipment or any of its parts should not be altered without the prior written approval of the manufacturer.

The user of this equipment shall have the sole responsibility for any malfunction which results from improper use,

faulty maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a service facility

designated by the manufacturer.

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR

OPERATING.

PROTECT YOURSELF AND OTHERS!

TABLE OF CONTENTS

SECTION 1: SAFETY ........................................................................................ 1-1

1.0 Safety Precautions .......................................................................................... 1-1

SECTION 2 SYSTEM:

INTRODUCTION ..................................................................................... 2-1

2.01 How To Use This Manual ................................................................................ 2-1

2.02 Equipment Identiﬁcation ................................................................................. 2-1

2.03 Receipt Of Equipment ..................................................................................... 2-1

2.04 Description ..................................................................................................... 2-2

2.05 Transportation Methods .................................................................................. 2-2

2.06 User Responsibility ......................................................................................... 2-2

2.07 Fabricator 211i Portable System Package (Part No. W1004201) .................... 2-2

2.08 Duty Cycle ....................................................................................................... 2-3

2.09 Speciﬁcations ................................................................................................. 2-4

Optional Accessories ...................................................................................... 2-6

2.11 Volt-Ampere Curves ........................................................................................ 2-7

SECTION 3: INSTALLATION, OPERATION AND SETUP ................................................ 3-1

3.01 Environment ................................................................................................... 3-1

3.02 Location .......................................................................................................... 3-1

3.03 Ventilation ....................................................................................................... 3-1

3.04 Electricity Supply ........................................................................................... 3-1

3.05 Electromagnetic Compatibility ........................................................................ 3-3

3.06 ESAB Regulator .............................................................................................. 3-4

3.07 Leak Testing The System ................................................................................ 3-6

When You Finish Using The Regulator ............................................................ 3-6

3.09 Storage Of The Regulator ............................................................................... 3-6

3.10 Fabricator 211i Power Source Controls, Indicators And Features ................... 3-7

3.11 Attaching the ESAB Fusion 220A MIG Gun ................................................... 3-13

3.12 Installing 33/44 lb Spool (12" diameter) ...................................................... 3-14

3.13 Installing 12.5 lb Spool ( 8" diameter) .......................................................... 3-15

3.14 Installing 1 lb Spool (4" diameter) ................................................................ 3-16

3.15 Inserting Wire Into The Wire Feed Mechanism ............................................. 3-17

3.16 Feed Roller Pressure Adjustment .................................................................. 3-18

3.17 Changing the Feed Roll ................................................................................. 3-18

3.18 Wire Reel Brake ............................................................................................ 3-19

3.19 Setup For MIG (GMAW) Welding With Gas Shielded MIG Wire .................... 3-19

3.20 Setup For MIG (FCAW) Welding With Flux Core (Gasless) Wire ................... 3-21

3.21 Setup For SPOOL GUN MIG (GMAW) Welding With Gas Shielded MIG Wire 3-22

3.22 Setup For LIFT TIG (GTAW) Welding ............................................................. 3-23

3.23 Setup For STICK (SMAW) Welding .............................................................. 3-25

TABLE OF CONTENTS

SECTION 4:

BASIC WELDING GUIDE ............................................................................. 4-1

4.01 MIG (GMAW/FCAW) Basic Welding Technique ............................................... 4-1

4.02 MIG (GMAW/FCAW) Welding Troubleshooting ............................................... 4-5

4.03 STICK (SMAW) Basic Welding Technique ....................................................... 4-8

4.04 Effects of Arc Welding Various Materials ........................................................ 4-8

4.04 STICK (SMAW) Welding Troubleshooting ..................................................... 4-15

4.05 TIG (GTAW) Basic Welding Technique .......................................................... 4-17

4.06 TIG (GTAW) Welding Problems ..................................................................... 4-19

SECTION 5: POWER SOURCE PROBLEMS AND ROUTINE SERVICE REQUIREMENTS ............ 5-1

5.01 Power Source Problems ................................................................................. 5-1

5.02 Routine Service and Calibration Requirements ............................................... 5-2

5.03 Cleaning the Welding Power Source ............................................................... 5-5

5.04 Cleaning the Feed Rolls ................................................................................... 5-6

SECTION 6: KEY SPARE PARTS .......................................................................... 6-1

6.01 Tweco Fusion 220A MIG Gun .......................................................................... 6-1

6.02 Power Source Spare Parts .............................................................................. 6-2

APPENDIX 1: FABRICATOR 211i CIRCUIT DIAGRAM ................................................. A-1

REVISION HISTORY ........................................................................................ A-2

INTERNATIONAL CONTACT INFORMATION ................................................. REAR COVER

ESAB FABRICATOR 211i

Manual 0-5422 1-1 SAFETY INSTRUCTIONS AND WARNINGS

1.0 Safety Precautions

Users of ESAB welding and plasma cutting equipment have the ultimate responsibility for ensuring that anyone who works

on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements

that apply to this type of welding or plasma cutting equipment. The following recommendations should be observed in

addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well acquainted with the operation of the welding or plasma cutting

equipment. Incorrect operation of the equipment may lead to hazardous situations which can result in injury to the

operator and damage to the equipment.

1. Anyone who uses welding or plasma cutting equipment must be familiar with:

- its operation

- location of emergency stops

- its function

- relevant safety precautions

- welding and / or plasma cutting

2. The operator must ensure that:

- no unauthorized person stationed within the working area of the equipment when it is started up.

- no one is unprotected when the arc is struck.

3. The workplace must:

- be suitable for the purpose

- be free from drafts

4. Personal safety equipment:

- Always wear recommended personal safety equipment, such as safety glasses, ﬂame proof

clothing, safety gloves.

- Do not wear loose ﬁtting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions:

- Make sure the return cable is connected securely.

- Work on high voltage equipment may only be carried out by a qualiﬁed electrician.

- Appropriate ﬁre extinguishing equipment must be clearly marked and close at hand.

- Lubrication and maintenance must not be carried out on the equipment during operation.

Dispose of electronic equipment at the recycling facility!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic Equipment and its

implementation in accordance with national law, electrical and/or electronic equipment that has reached

the end of its life must be disposed of at a recycling facility.

As the person responsible for the equipment, it is your responsibility to obtain information on approved

collection stations.

For further information contact the nearest ESAB dealer.

ESAB can provide you with all necessary cutting protection and accessories.

SECTION 1: SAFETY

ESAB FABRICATOR 211i

SAFETY INSTRUCTIONS AND WARNINGS 1-2 Manual 0-5422

WARNING

Arc welding and cutting can be injurious to yourself and others.

Take precautions when welding and cutting. Ask for your employer's

safety practices which should be based on manufacturers' hazard

data.

ELECTRIC SHOCK - Can kill.

- Install and earth (ground) the welding or plasma cutting unit in accordance with appli-

cable standards.

- Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet cloth-

ing.

- Insulate yourself from earth and the workpiece.

- Ensure your working stance is safe.

FUMES AND GASES - Can be dangerous to health.

- Keep your head out of the fumes.

- Use ventilation, extraction at the arc, or both, to take fumes and gases away from

your breathing zone and the general area.

ARC RAYS - Can injure eyes and burn skin.

- Protect your eyes and body. Use the correct welding / plasma cutting screen and

ﬁlter lens and wear protective clothing.

- Protect bystanders with suitable screens or curtains.

FIRE HAZARD

- Sparks (spatter) can cause ﬁre. Make sure therefore that there are no inﬂammable

materials nearby.

NOISE - Excessive noise can damage hearing.

- Protect your ears. Use earmuffs or other hearing protection.

- Warn bystanders of the risk.

MALFUNCTION - Call for expert assistance in the event of malfunction.

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERAT-

ING.

PROTECT YOURSELF AND OTHERS!

WARNING

Do not use the power source for thawing frozen pipes.

CAUTION

Class A equipment is not intended for use in residential locations

where the electrical power is provided by the public low-voltage

supply system. There may be potential difﬁculties in ensuring

electromagnetic compatibility of class A equipment in those loca-

tions, due to conducted as well as radiated disturbances.

CAUTION

This product is solely intended for metal removal. Any other use

may result in personal injury and / or equipment damage.

CAUTION

Read and understand the instruction manual before

installing or operating.

ESAB FABRICATOR 211i

Manual 0-5422 2-1 INTRODUCTION

SECTION 2 SYSTEM:

INTRODUCTION

2.01 How To Use This Manual

This Owner’s Manual applies to just speciﬁcation or part numbers

listed on page i.

To ensure safe operation, read the entire manual, including the

chapter on safety instructions and warnings.

Throughout this manual, the words WARNING, CAUTION, DANGER,

and NOTE may appear. Pay particular attention to the information

provided under these headings. These special annotations are

easily recognized as follows:

NOTE!

An operation, procedure, or background

information which requires additional

emphasis or is helpful in efﬁcient operation

of the system.

CAUTION

A procedure which, if not properly followed,

may cause damage to the equipment.

WARNING

A procedure which, if not properly followed,

may cause injury to the operator or others

in the operating area.

WARNING

Gives information regarding possible electri-

cal shock injury. Warnings will be enclosed

in a box such as this.

DANGER

Means immediate hazards which, if not

avoided, will result in immediate, serious

personal injury or loss of life.

Additional copies of this manual may be purchased by contacting

ESAB at the address and phone number in your area listed on

back cover of this manual. Include the Owner’s Manual number

and equipment identiﬁcation numbers.

Electronic copies of this manual can also be downloaded at no

charge in Acrobat PDF format by going to the ESAB web site

listed below

http://www.esab.com

2.02 Equipment Identiﬁcation

The unit’s identiﬁcation number (speciﬁcation or part number),

model, and serial number usually appear on a data tag attached

to the rear panel. Equipment which does not have a data tag

such as torch and cable assemblies are identiﬁed only by the

speciﬁcation or part number printed on loosely attached card or

the shipping container. Record these numbers on the bottom of

page i for future reference.

2.03 Receipt Of Equipment

When you receive the equipment, check it against the invoice to

make sure it is complete and inspect the equipment for pos-

sible damage due to shipping. If there is any damage, notify the

carrier immediately to ﬁle a claim. Furnish complete information

concerning damage claims or shipping errors to the location in

your area listed in the inside back cover of this manual.

Include all equipment identiﬁcation numbers as described above

along with a full description of the parts in error.

Move the equipment to the installation site before un-crating

the unit. Use care to avoid damaging the equipment when using

bars, hammers, etc., to un-crate the unit.

ESAB FABRICATOR 211i

INTRODUCTION 2-2 Manual 0-5422

2.04 Description

The ESAB Fabricator 211i is a self contained single phase multi

process welding system that is capable of performing MIG

(GMAW/FCAW), STICK (SMAW) and LIFT TIG (GTAW) welding

processes. The Power Source is equipped with an integrated wire

feed unit, digital voltage and amperage meters, and a host of

other features in order to fully satisfy the broad operating needs

of the modern welding professional. The Power Source is also

fully compliant to Standard CSA E60974-1-00 and UL 60974.1.

The ESAB Fabricator 211i provides excellent welding perfor-

mance across a broad range of applications when used with

the correct welding consumables and procedures. The following

instructions detail how to correctly and safely set up the machine

and give guidelines on gaining the best efﬁciency and quality

from the Power Source. Please read these instructions thoroughly

before using the unit.

2.05 Transportation Methods

WARNING

ELECTRIC SHOCK can kill. DO NOT TOUCH

live electrical parts. Disconnect input power

conductors from de-energized supply line

before moving the welding power source.

WARNING

FALLING EQUIPMENT can cause serious

personal injury and equipment damage.

Lift Power Source with handles built into the top of the front and

rear molded panels.

Use handcart or similar device of adequate capacity.

If using a fork lift vehicle, place and secure Power Source on a

proper skid before transporting.

2.06 User Responsibility

This equipment will perform as per the information contained

herein when installed, operated, maintained and repaired in

accordance with the instructions provided. This equipment must

be checked periodically. Defective equipment (including welding

leads) should not be used. Parts that are broken, missing, plainly

worn, distorted or contaminated, should be replaced immediately.

Should such repairs or replacements become necessary, it is

recommended that such repairs be carried out by appropriately

qualiﬁed persons approved by ESAB. Advice in this regard can be

obtained by contacting an Accredited ESAB Distributor.

This equipment or any of its parts should not be altered from

standard speciﬁcation without prior written approval of ESAB.

The user of this equipment shall have the sole responsibility for

any malfunction which results from improper use or unauthorized

modiﬁcation from standard speciﬁcation, faulty maintenance,

damage or improper repair by anyone other than appropriately

qualiﬁed persons approved by ESAB.

2.07 Fabricator 211i Portable System

Package (Part No. W1004201)

• Fabricator 211i Power Source

• 12 ft. (3.6 m) ESAB

Fusion 220 Amp MIG Gun

• Victor Argon Regulator / Flowmeter

• Drive Rolls:

.023"/.030" (0.6/0.8 mm) "V" groove,

.023"/.035" (0.6/0.9 mm)"V" groove (tted with .035"

groove lined up),

.030"/.035" (0.8/0.9 mm) "V" knurled for Flux Cored Wire,

• Velocity Contact Tips (1 each)

.023"(0.6 mm), .030"(0.8 mm),

.035"(0.9 mm) (tted)

.045"(1.2 mm)

• Electrode Holder with 13 ft. (4 m) lead

• Work Clamp with 10 ft. (3.1 m) lead

• Shielding Gas hose assembly

• 15A/20A Adapter Plug from 208/230V AC 50 Amps to 115V

Amps Circuits

• ESAB Cap

• Electrodes

• Large Spring

• Operating Manual

• DVD

A-12923

Figure 2-1: Fabricator 211i System Packaged W1004201

ESAB FABRICATOR 211i

Manual 0-5422 2-3 INTRODUCTION

2.08 Duty Cycle

The rated duty cycle of a Welding Power Source, is a statement of the time it may be operated at its rated welding current output with-

out exceeding the temperature limits of the insulation of the component parts. To explain the 10 minute duty cycle period the following

example is used. Suppose a Welding Power Source is designed to operate at a 20% duty cycle, 210 amperes at 24.5 volts. This means

that it has been designed and built to provide the rated amperage (210A) for 2 minutes, i.e. arc welding time, out of every 10 minute

period (20% of 10 minutes is 2 minutes). During the other 8 minutes of the 10 minute period the Welding Power Source must idle and

allowed to cool. The thermal cut out will operate if the duty cycle is exceeded.

10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220

FABRICATOR 211i

Welding Current (AMPS)

SAFE OPERATING REGION

(MIG, TIG & STICK)

100

Duty Cycle (PERCENTAGE)

MIG

STICK / TIG

Art # A-11265

Figure 2-2: Fabricator 211i Duty Cycle on 208/230V AC

Welding Current (AMPS)

Duty Cycle (PERCENTAGE)

Art # A-11274

100

0102030405060708090100 110 120 130140 150

FABRICATOR 211i

SAFE OPERATING REGION

(MIG, TIG & STICK)

TIG

STICK

MIG

Figure 2-3: Fabricator 211i Duty Cycle on 115V AC

ESAB FABRICATOR 211i

INTRODUCTION 2-4 Manual 0-5422

2.09 Speciﬁcations

Description Fabricator 211i Multi Process 3 in 1 Welder

Power Source Part No. W1004200

Power Source Dimensions H17.12" x W10.47" x D 24.29" (435mm x 266mm x D617mm)

Power Source Mass 57.3lb (26kg)

Cooling Fan Cooled

Welder Type Multi Process Welding System

Applicable Standard CSA E60974-1-00 / UL60974-1 / IEC 60974-1

Number of Phases Single Phase

Nominal Supply Voltage 208/230 VAC ± 10% 115VAC± 10%

Nominal Supply Frequency 50/60Hz 50/60HZ

Welding Current Range

MIG Mode

STICK Mode

TIG Mode

10-210 Amps

10-200 Amps

10-140 Amps

10-110 Amps

10-150 Amps

Wirefeed Speed Range 100 - 600 IPM 100 - 400 IPM

MIG Welding Voltage Range 14.5 - 24.5V DC 14.5 - 19V DC

Nominal OCV 70V DC

Effective Input Current (I1eff)

for MIG (GMAW/FCAW)

for STICK (SMAW)

for LIFT TIG (GTAW)

14.4A/11.2A

16.8A/15.8A

11.7A/11.5A

15.5A

17.8A

17.4A

Maximum Input Current (I1max)

for MIG (GMAW/FCAW)

for STICK (SMAW)

for LIFT TIG (GTAW)

32.2A/25.0A

33.6A/31.6A

23.3A/22.9A

24.5A

30.1A

29.4A

Single Phase Generator Requirement 7.5 kVA *3.7 kVA

MIG (GMAW/FCAW) Welding Output, 104°F, 10 min. 210A @ 20%,24.5V

122A @ 60%, 20.1V

95A @ 100%, 18.8V

110A @ 45%,19.5V

99A @ 60%, 19.0V

77A @ 100%, 17.9V

STICK (SMAW) Welding Output,1040°F, 10 min. 200A @ 25%,28.0V

130A @ 60%, 25.2V

101A @ 100%, 24.0V

110A @ 35%,24.4V

90A @ 60%, 23.6V

70A @ 100%, 22.8V

TIG (GTAW) Welding Output, 104°F, 10 min. 200A @ 25%,18.0V

130A @ 60%, 15.2V

101A @ 100%, 14.0V

150A @ 35%,16.0V

115A @ 60%, 14.6V

90A @ 100%, 13.6V

Open Circuit Voltage 70 V

Protection Class IP23S

Table 2-1: Fabricator 211i Speciﬁcations

Note 1: The Effective Input Current should be used for the determination of cable size & supply requirements.

Note 2: Motor start fuses or thermal circuit breakers are recommended for this application. Check local requirements for your situ-

ation in this regard.

Note 3: Generator Requirements at the Maximum Output Duty Cycle.

* Some 115 VAC, 15 amp/20 amps electrical outlets tted with GFCI (Ground Fault Circuit Interrupt) protection against a nuisance trip

with this equipment due to worn or out of tolerance components in the GFCI. In such cases have the 115 VAC, 15 amp/20 amp FGCI

electrical outlet replaced by a qualiﬁed electrical trades person.

ESAB FABRICATOR 211i

Manual 0-5422 2-5 INTRODUCTION

NOTE!

The recommended time delay fuse or circuit breaker size for 115V is 30 amp. An individual branch circuit

capable of carrying 30 amperes and protected by fuses or circuit breaker is recommended for this applica-

tion. Fuse size is based on not more than 200 percent of the rated input amperage of the welding Power

Source (Based on Article 630, National Electrical Code)

ESAB continuously strives to produce the best product possible and therefore reserves the right to change,

improve or revise the speciﬁcations or design of this or any product without prior notice. Such updates or

changes do not entitle the buyer of equipment previously sold or shipped to the corresponding changes,

updates, improvements or replacement of such items.

The values speciﬁed in the table above are optimal values, your values may differ. Individual equipment

may differ from the above speciﬁcations due to in part, but not exclusively, to any one or more of the fol-

lowing; variations or changes in manufactured components, installation and conditions and local power grid

supply conditions..

ESAB FABRICATOR 211i

INTRODUCTION 2-6 Manual 0-5422

Optional Accessories

26V TIG Torch & Accessories (required for TIG welding) Part No. W4014603

ESAB Spool Gun (required for aluminum MIG welding) Part No. 1027-1390

Professional 4 Wheel Cart, Dual Cylinder ................... Part No. W4015002

Professional 4 Wheel Cart, Single Cylinder ................ Part No. W4015001

Small Cart, Single Cylinder .......................................... Part No. W4014700

Roll Cage ...................................................................... Part No. W4015104

Foot Control ................................................................. Part No. 600285

ESAB Helmet (USA Only) ............................ Part No. 4100-1004

Drive Roll .023" - .030" (0.6/0.8mm ) V groove, (ﬁtted) Part No. 7977036

Drive Roll .023" - .035" (0.6/0.9 mm) V groove . Part No. W4014800

Drive Roll .035"/.045" (0.9/1.2 mm) V groove .. Part No. 7977660

Drive Roll .030" - .035" (0.8/0.9 mm) U groove .. Part No. 7977731

Drive Roll .040" - 3/64" (1.0/1.2 mm) U groove . Part No. 7977264

Drive Roll .030" - .035" (0.8/0.9 mm) V knurled Part No. 7977732

Drive Roll .045"(1.2 mm) V knurled ............. Part No. 704277

Stick Lead, 200A, 13ft, 50mm Dinse ............. Part No. WS200E13

Ground Lead, 200A, 10Ft, 50mm Dinse .......... Part No. WS200G10

ESAB Regulator/ Flowgauge ................................ Part No. 130781-4169

Accessory Kit for TIG Torch ................................... Part No. P062900010

12.5 ft cable length; 12.5 ft gas hose length; 8 pin control

plug; 1/16", 3/32", 1/8" thoriated tungstens; 1/16", 3/32",

1/8" collets; 1/16", 3/32",1/8:" collet bodies; No. 5, 6, 7

Alumina nozzle; short back cap; long back cap

160A, 12ft (3.6M) Length, suits 4" (100mm) spools

For remote amperage control when TIG welding

WeldSkill Auto-Darkening Helmet Skull & Fire (USA Only)

1/16", 3/32", 1/8" thoriated tungstens; 1/16", 3/32", 1/8"

collets; 1/16", 3/32",1/8:" collet bodies; No. 5, 6, 7

Alumina nozzle; short back cap; long back cap

ESAB FABRICATOR 211i

Manual 0-5422 2-7 INTRODUCTION

2.11 Volt-Ampere Curves

Voltage-Amperage Curves shows maximum voltage and amperage output capabilities of welding power source. Curves of other set-

tings fall between curves shown.

Art # A-11297

Figure 2-4: Fabricator 211i Volt-Ampere Curves

ESAB FABRICATOR 211i

INTRODUCTION 2-8 Manual 0-5422

This Page Intentionally Blank

ESAB FABRICATOR 211i

Manual 0-5422 3-1 SAFETY INSTRUCTIONS AND WARNINGS

3.01 Environment

This Power Source is designed for use in environments with

increased hazard of electric shock. Additional safety precautions

may be required when using unit in an environment with

increased hazard of electric shock. Please refer to relevant local

standards for further information prior to using in such areas.

A. Examples of environments with increased hazard of electric

shock are:

1. In locations in which freedom of movement is restricted,

so that the operator is forced to perform the work in a

cramped (kneeling, sitting or lying) position with physi-

cal contact with conductive parts.

2. In locations which are fully or partially limited by con-

ductive elements, and in which there is a high risk of

unavoidable or accidental contact by the operator.

3. In wet or damp hot locations where humidity or perspi-

ration considerably reduces the skin resistance of the

human body and the insulation properties of accesso-

ries.

B. Environments with increased hazard of electric shock

do not include places where electrically conductive parts in the

near vicinity of the operator, which can cause increased hazard,

have been insulated.

3.02 Location

Be sure to locate the welder according to the following guide-

lines:

A. In areas, free from moisture and dust.

B. Ambient temperature between 14° F (0° C) to 104° F (40°

C).

C. In areas, free from oil, steam and corrosive gases.

D. In areas, not subjected to abnormal vibration or shock.

E. In areas, not exposed to direct sunlight or rain.

F. Place at a distance of 12" (305mm) or more from walls or

similar that could restrict natural air ﬂow for cooling.

G. The enclosure design of this Power Source meets the re-

quirements of IP23S as outlined in EN 60529. This provides

adequate protection against solid objects (greater than 1/2",

12mm) and direct protection from vertical drops. Under

no circumstances should the Power Source be operated

or connected in a micro environment that will exceed the

stated conditions. For further information please refer to

EN 60529.

H. Precautions must be taken against the power source top-

pling over. The power source must be located on a suitable

horizontal surface in the upright position when in use.

SECTION 3: INSTALLATION,

OPERATION AND SETUP

WARNING

This equipment should be electrically con-

nected by a qualiﬁed electrician.

3.03 Ventilation

WARNING

Since the inhalation of welding fumes can

be harmful, ensure that the welding area is

effectively ventilated.

3.04 Electricity Supply

CAUTION

The Electricity Supply voltage should be within

208/230V AC ± 10% or 115 V AC ± 10%. Too

low a supply voltage may cause poor welding

performance in STICK mode such as the arc

snufﬁng out during welding. Too high a supply

voltage will cause components to overheat and

possibly fail. The Welding power Source must

be:

• Correctly installed, if necessary, by a qualied

electrician.

• Correctly earthed (electrically) in accordance

with local regulations.

• Connected to the correct size power point and

fuse as per the Speciﬁcations on page 2-4.

WARNING

The Fabricator 211i must be electrically

connected by a qualiﬁed electrical trades-

person. Damage to the PCA (Power Control

Assembly) could occur if 265 VAC or higher

is applied to the Primary Power Cable.

WARNING

ELECTRIC SHOCK can kill; SIGNIFICANT DC

VOLTAGE is present after removal of input

power. DO NOT TOUCH live electrical parts.

SHUT DOWN welding power source, disconnect input power em-

ploying lockout/tagging procedures. Lock-out/tagging procedures

consist of padlocking line disconnect switch in open position,

removing fuses from fuse box, or shutting OFF and red-tagging

circuit breaker or other disconnecting device.

ESAB FABRICATOR 211i

INSTALLATION/SETUP 3-2 Manual 0-5422

Power Cords Included With Power Supply

Attached to the power supply is an input power cord with a 208/230Volt 50 Amp NEMA 6-50 P for plug. Supplied adapter allow for con-

nection of the power supply input cable plug to 115 V input power.

Art# A-11275

Figure 3-1: 115 VAC Adapter

Electrical Input Requirements

Operate the welding power source from a single-phase 50/60 Hz, AC power supply. The input voltage must match one of the electrical

input voltages shown on the input data label on the unit nameplate. Contact the local electric utility for information about the type of

electrical service available, how proper connections should be made, and inspection required. The line disconnect switch provides a

safe and convenient means to completely remove all electrical power from the welding power supply whenever necessary to inspect or

service the unit. The Welding Power Source must be:

Do not connect in input (WHITE or BLACK) conductor to the ground terminal.

Do not connect the ground (GREEN) conductor to an input line terminal.

• Correctly installed, if necessary, by a qualied electrician.

• Correctly earthed (electrically) in accordance with local regulations.

• Connected to the correct size power point, fuse and primary supply lead based on Table 3-1.

Refer to Figure 3-1 and Table 3-1.

WARNING

An electrical shock or ﬁre hazard is probable if the following electrical service guide recommendations are

not followed. These recommendations are for a dedicated branch circuit sized for the rated output and duty

cycle of the welding Power Source.

50 / 60 Hz Single Phase Supply

Supply Voltage 208/230V AC 115V AC

Input Current at Maximum Output 32 Amps 30 Amps

Maximum Recommended Fuse* or Circuit Breaker Rating * Time

Delay Fuse, UL class RK5. Refer to UL248

50 Amps 30 Amps

Maximum Recommended Fuse^ or Circuit Breaker Rating ^Normal

Operating, UL class K5. Refer to UL248

50 Amps 30 Amps

Minimum Recommended Cord Size 12 AWG 12 AWG

Maximum Recommended Extension Cord Length 50 ft 25 ft

Minimum Recommended Grounding Conductor Size 12 AWG 12AWG

Table 3-1: Electrical Service Guide

CAUTION

The time-delay fuses or circuit breaker of an individual branch circuit may have nuisance tripping when

welding with this product due to the amperage rating of the time-delay fuses or circuit breaker.

ESAB FABRICATOR 211i

Manual 0-5422 3-3 SAFETY INSTRUCTIONS AND WARNINGS

Art# A-11240

Primary Power Cable

115

20A,1Ø

15A,1Ø

208/230V, 50A,1Ø

The Adapter enable

connection to all these

power outlets

115 VAC Adapter

Figure 3-2: Electrical Input Connections

3.05 Electromagnetic Compatibility

WARNING

Extra precautions for Electromagnetic Compatibility may be required when this Welding Power

Source is used in a domestic situation.

A. Installation and Use - Users Responsibility

The user is responsible for installing and using the welding equipment according to the manufacturer’s instructions. If electromag-

netic disturbances are detected then it shall be the responsibility of the user of the welding equipment to resolve the situation with

the technical assistance of the manufacturer. In some cases this remedial action may be as simple as earthing the welding circuit, see

NOTE below. In other cases it could involve constructing an electromagnetic screen enclosing the Welding Power Source and the work,

complete with associated input ﬁlters. In all cases, electromagnetic disturbances shall be reduced to the point where they are no longer

Troublesome.

NOTE!

The welding circuit may or may not be earthed for safety reasons. Changing the earthing arrangements

should only be authorized by a person who is competent to assess whether the changes will increase the

risk of injury, e.g. by allowing parallel welding current return paths which may damage the earth circuits of

other equipment.

ESAB FABRICATOR 211i

INSTALLATION/SETUP 3-4 Manual 0-5422

4. Equipotential Bonding

Bonding of all metallic components in the welding instal-

lation and adjacent to it should be considered. However,

metallic components bonded to the work piece will increase

the risk that the operator could receive a shock by touch-

ing the metallic components and the electrode at the same

time. The operator should be insulated from all such bonded

metallic components.

5. Earthing/grounding of the Work Piece

Where the work piece is not bonded to earth for electrical

safety, nor connected to earth because of its size and posi-

tion, e.g. ship’s hull or building steelwork, a connection

bonding the work piece to earth may reduce emissions in

some, but not all instances. Care should be taken to prevent

the earthing of the work piece increasing the risk of injury

to users, or damage to other electrical equipment. Where

necessary, the connection of the work piece to earth should

be made by direct connection to the work piece, but in

some countries where direct connection is not permitted,

the bonding should be achieved by suitable capacitance,

selected according to national regulations.

6. Screening and Shielding

Selective screening and shielding of other cables and

equipment in the surrounding area may alleviate problems

of interference. Screening the entire welding installation

may be considered for special applications.

3.06 ESAB Regulator

Pressure regulator (Figure 3-3) attached to the cylinder valve

reduce high cylinder pressures to suitable low working pressures

for welding, cutting, and other applications.

LOW PRESSURE

GAUGE (DELIVERY)

HIGH PRESSURE

GAUGE (SUPPLY)

INLET

CONNECTION

OUTLET

CONNECTION

PRESSURE

ADJUSTING

SCREW

A-09414_AC

Figure 3-3: ESAB CS Regulator

WARNING

Use the regulator for the gas and pressure

for which it is designed. NEVER alter a

regulator for use with any other gas.

NOTE!

Regulators purchased with open 1/8”, 1/4”,

3/8”, or 1/2” NPT ports must be assembled

to their intended system.

B. Assessment of Area

Before installing welding equipment, the user shall make

an assessment of potential electromagnetic problems in the

surrounding area. The following shall be taken into account.

1. Other supply cables, control cables, signaling and telephone

cables; above, below and adjacent to the welding equipment.

2. Radio and television transmitters and receivers.

3. Computer and other control equipment.

4. Safety critical equipment, e.g. guarding of industrial

equipment.

5. The health of people around, e.g. the use of pace-makers

and hearing aids.

6. Equipment used for calibration and measurement.

7. The time of day that welding or other activities are to be

carried out.

8. The immunity of other equipment in the environment: the

user shall ensure that other equipment being used in the

environment is compatible: this may require additional

protection measures.

The size of the surrounding area to be considered will depend on

the structure of the building and other activities that are taking

place. The surrounding area may extend beyond the boundaries

of the premises.

C. Methods of Reducing Electromagnetic Emissions

1. Electricity Supply

Welding equipment should be connected to the Electricity

Supply according to the manufacturer’s recommendations.

If interference occurs, it may be necessary to take additional

precautions such as ﬁltering of the Electricity Supply.

Consideration should be given to shielding the supply cable

of permanently installed welding equipment in metallic

conduit or equivalent. Shielding should be electrically

continuous throughout its length. The shielding should

be connected to the Welding Power Source so that good

electrical contact is maintained between the conduit and

the Welding Power Source enclosure.

2. Maintenance of Welding Equipment

The welding equipment should be routinely maintained

according to the manufacturer’s recommendations. All

access and service doors and covers should be closed

and properly fastened when the welding equipment is in

operation. The welding equipment should not be modiﬁed in

any way except for those changes and adjustments covered

in the manufacturer’s instructions.

3. Welding Cables

The welding cables should be kept as short as possible and

should be positioned close together but never coiled and

running at or close to the ﬂoor level.

Page is loading ...

ESAB FABRICATOR® 211i 3-IN-1 Multi Process Welding Systems User manual

Brand: ESAB

Model: FABRICATOR® 211i 3-IN-1 Multi Process Welding Systems

Category: Welding System

Type: User manual

This manual is also suitable for

ESAB Fabricator® 211i 3-IN-1 Multi Process Welding Systems

Download PDF

report

ESAB FABRICATOR® 211i 3-IN-1 Multi Process Welding Systems User manual

This manual is also suitable for

ESAB FABRICATOR® 211i 3-IN-1 Multi Process Welding Systems User manual

Related papers

Other documents