ON Semiconductor EVBUM2798 User guide

Brand: ON Semiconductor

Model: EVBUM2798

Type: User guide

This manual is also suitable for

EVBUM2798 Board

ON Semiconductor EVBUM2798 is an Arduino shield form factor containing a single NCL31000MNITWG LED driver, allowing evaluation of the product with USB to I2C interface or Arduino microcontroller. It features configurable dimming options, including MDAC, ADIM, ADIMP, PWMDIM, and INTDIM, enabling precise control of LED current. Additionally, it supports Visual Light Communication (VLC) using the MDAC or ADIM + PWMVLC methods, allowing data transmission by modulating LED current. The board has four LEDs for status indication and a significant copper cooling plane for efficient heat dissipation.

June, 2021 − Rev. 1

1Publication Order Number:

EVBUM2798/D

NCL31000ASGEVB User

Guide

EVBUM2798/D

Introduction

This guide explains how to use the NCL31000ASGEVB

with an USB to I2C interface or with an arduino

microcontroller board of choice to evaluate the product.

Board Connections

The NCL31000ASGEVB (Figure 1) is an arduino shield

form factor containing a single NCL31000MNITWG LED

driver. These few steps are required to get started.

1. Connect a lab power supply from 24 V to 57 V to

the DC IN connector. A reverse polarity protection

circuit is in place to protect the system against

faulty connections.

2. Connect a LED string rated for 16 V to 42 V to the

LED connector.

3. Optionally, connect an NTC from the LED module

to the TLED connector to measure the LED board

temperature. If doing so, remove R24 and short

R33, see section LED Power.

4. Connect a microcontroller to the arduino interface

connectors and develop firmware to evaluate the

product.

5. An alternative for step 4 is to use an USB to I2C

interface to send commands from the PC to

NCL31000ASGEVB.

Micro−Controller Interface

The NCL31000 hardware requires at least a GND

connection and an I2C or SPI connection to control the main

functions of the chip. The SCL/SDA and connections are

designated to Arduino pins D15 and D14. All Nucleo boards

can be programmed to route an I2C peripheral to these pins.

The default I2C address is 0x52. This is configurable

with zero−ohm resistors.

The NCL310xx devices are internally hardwired to use

either SPI or I2C. For now, NCL31000ASGEVB is only

available with the I2C version populated. Note that the SPI

slave in NCL310xx only supports Mode 2.

For Visual Light Communication, preferably a DAC

connection or alternatively 2 x PWM connections are

needed. See section Dimming and VLC − YellowDot.

The DAC connection is not specified by the Arduino

hardware interface and different microcontroller boards

connect the DAC to different pins. By default,

the NCL31000ASGEVB assumes the DAC can be

connected to A2 or D13 (see Schematic). This is compatible

with the ST Nucleo boards.

Figure 1. NCL31000ASGEVB

www.onsemi.com

EVAL BOARD USER’S MANUAL

EVBUM2798/D

www.onsemi.com

DC−DCs

Two DC−DC supplies are available to supply different

parts of the application. VDD1 is a fixed 3.3 V supply rated

to deliver up to 150 mA and VDD2 is configurable, but on

the EVB it is set for 5 V. It can source up to 500 mA. VDD1

and VDD2 are not connected to the arduino interface so

VDD1 does not by default supply the arduino board because

the arduino interface standard does not provide a 3V3 supply

connection. Some arduino micro−controller boards can be

adjusted so that they can be supplied with 3V3. For example,

the nucleo boards normally need one or more solder bridge

configuration changes to be able to get powered from a 3V3

supply. See the VDD1_EXT connection in the schematic.

The VDD2 cannot be used to supply the micro−controller

since it has to be enabled first in a register after startup. Thus,

by default, without making any changes to the hardware, the

micro−controller board has to be supplied by the USB

connection or another supply.

LED Power

This EVB has a significant copper cooling plane for the

top fet of the LED driver. It is therefore possible to drive

LED loads up to 100 W with this EVB. 2 NTC’s are placed

onto the cooling plane to measure the plane’s temperature to

estimate the top fet junction temperature. One NTC is

connected to the TLED metrology measurement pin so that

the temperature can be monitored over I2C. The second

NTC is electrically connected on one side to the copper

plane and one side floating so that a multimeter can measure

the voltage over the NTC. This is an alternative NTC sensing

method. To measure the NTC voltage from the LED board,

make the connection to the TLED connector and solder R24

and remove R33 to disable the top fet measurement.

It is best to replace the sense resistor with 50 m or place

a second resistor in parallel to reduce the temperature of the

sense resistor and the dissipation when going above 1.6 A

LED current or so. See the Thermal section for more info.

Dimming

To make dimming possible, enable the LED driver by

setting the LED_EN bit in the CTRL register and close the

PWM_EN jumper on the EVB.

There are 5 ways to dim the LEDs. The selection for the

first three methods is made with the DIMSEL jumpers. See

Figure 2.

Figure 2. Dimsel

•MDAC: DAC in MCU connected to DIM pin (Arduino:

A2 or D13)

•ADIM: Analog dimming. A low−pass filtered DC

signal converted from a PWM signal from MCU

(Arduino: D5)

•ADIMP: potmeter on the EVB connected to DIM pin

The others are (DIMSEL does not matter):

•PWMDIM: PWM dimming. PWM from MCU directly

to PWM pin (Arduino: D9)

•INTDIM: The internal 7−bit DAC

EVBUM2798/D

www.onsemi.com

INTDIM

The internal 7−bit DAC can be used to DIM the LEDs.

With 128 dimming steps in the entire range this method

provides a coarse method to dim the LEDs. The lowest

current value is about 10 mA if a 100 m sense resistor is

used. If deep dimming or VLC is not needed this method

may suffice. No extra hardware is needed, only the I2C or

SPI interface.

ADIM

The ADIM signal can dim the LEDs with a higher

accuracy and precision compared to the other methods. It is

possible to accurately dim down to about 0.1% of the

maximum range. The accuracy at these low dimming values

is dominated by the relative offset error, which is no more

than a few mV’s or approximately 0.1% of VREF. The

precision or resolution is defined by the amount of steps the

duty−cycle has in the PWM period. For example, if an 8−bit

timer is used, 256 steps are available. PWM oversampling

can increase this number.

The ADIM method is an alternative to the INTDIM

method. Switching between these methods is possible by

controlling the INTDIMEN bit. To use the ADIM method,

the micro−controller must provide a PWM signal with a

frequency preferably between 1 to 10 kHz. The duty−cycle

defines the dim value. This PWM signal is filtered heavily

and the resulting average value is presented to the DIM

input. The resulting LED current is thus a constant current,

not a PWM’ed current. This ADIM or the MDAC method

can use VLC. Next to low pass filtering the PWM signal, the

filtering circuit also couples the VLC signal on the DIM

signal. To make use of this method configure the DIMSEL

jumper for ADIM and pull the PWM pin high by closing the

PWM jumper.

PWMDIM

The PWMDIM does not provide the widest dim range or

best accuracy and should not be used as the primary dim

method, but it can be used on top of the ADIM method to

achieve hybrid dimming and dim to even lower LED

currents. For example, set ADIM to 220 mV and apply a

PWM signal of 1 kHz and 25% duty−cycle to achieve an

average internal DIM voltage of:

200 mV + 0.25 * 20 mV = 205 mV

Important to note is that the measured LED current from

the ILED metrology register is not valid when using

PWMDIM. This is because the ADC sampling is in the range

of 100 ms and the PWMDIM frequency is the range of

400 Hz and higher and thus oversampling is not possible and

no averaging can be done.

MDAC

This method uses the DAC in the micro−controller, if

available. This method can dim the LEDs and still have the

possibility to use VLC. To use the DAC, route it to A2 or D13

on the Arduino interface (possible for Nucleo−64 or

Nucleo−144 connections) and configure DIMSEL jumper

for ’MDAC’. When using the DAC you cannot use the

SPI_CLK and thus only I2C is an option. One exception is

the Nucleo−64 boards, which connect the DAC to A2 on the

Arduino interface. Also pull the PWM pin high by closing

the PWM jumper.

ADIMP

The potmeter on the EVB can be used to apply a voltage

on the dim pin and manually control the LED current. To

make use of this method configure the DIMSEL jumper for

ADIMP and pull the PWM pin high by closing the PWM

jumper.

Status Indication

The boards have four LEDs. Two green LEDs to indicate

the 3V3 (VDD1) and 5 V (VDD2) supplies are active. Note

that VDD1 must be active on power up. This is a good check

to see if the board (supplies) is operational. VDD2 is

disabled at startup and can be enabled in a register. The

orange INTB LED is active if the INTB line is low. This is

the case when a fault bit is active or became active since the

last read. The red FAULT LED can be used by the

micro−controller.

VLC − YellowDot

The YellowDot program is a luminaire certification

program that allows manufacturers to test and certify that

their LED luminaires are interoperable with Signify’s indoor

positioning technology. A key aspect of YellowDot ready

LED drivers is that data can be transmitted by modulating

data onto the LED current and thus in the light output. The

NCL310xx products are Yellow−dot compatible. This

means that it is possible to modulate the LED current

conform to the Yellow–dot specification. Contact Signify

for more information about this program and the technical

requirements. Modulating the data on the DIM pin can be

done either by using the MDAC (preferred) method or by

using the ADIM method together with the PWMVLC signal.

VLC with MDAC

The DAC voltage controls the DIM voltage directly.

When no data is transmitted, it should regulate a stable DC

value to provide a stable LED current. When transmitting

data, the DAC voltage swings between the 3 voltage levels

at the symbol rate.

VLC with ADIM + PWMVLC

An alternative for the DAC is to use 2 PWM signals. One

is for setting the DC dim value using the ADIM method and

the other PWM signal is connected to the PWMVLC signal.

The PWMVLC data is coupled onto the DIM signal. The

frequency must be about 200 kHz or more. A digital one is

represented by a duty−cycle of 50% + k. A digital zero is

represented by a duty−cycle of 50% − k. The resulting signal

is a 200 kHz PWM signal for which the duty−cycle varies

between 2 values (0.5 − k and 0.5 + k). The symbol rate of

the VLC signal (typ: 4 kHz) is defined by the rate at which

the duty−cycles alternate. The ’k’ value defines the

amplitude of the VLC signal. After filtering the resulting

EVBUM2798/D

www.onsemi.com

signal is a 4 kHz AC signal with a given amplitude. This

signal is capacitively coupled on the DIM signal so for this

to work the ADIM dimming method must be used to define

the DC DIM level.

Thermal

The highest temperatures on the board are to be expected

in the top fet of the LED driver and in the sense resistor of

the LED driver.

LED Sense Resistor

It is best to keep the sense resistor value as small as

possible without impacting the dynamic dimming range too

much. Keep the power dissipation in the 6430 package

below 400 mW. Ideally 200 mW. It is possible to add a sense

resistor in parallel to spread the dissipation (1% or better).

For example, a 120 m 6430 package with a 0.62  3216

package in parallel gives 100 m and a better spreading of

heat.

Thermal Plane

The power dissipation in the top fet is dominated by

switching and conduction losses. The device used on the

board is carefully selected to achieve the lowest power

dissipation. Still, mainly depending on the input voltage,

switching frequency and during highest current, the power

dissipation (Pt) can reach up to about 1.2 W in this device.

A copper cooling plane is required to transfer enough heat

to the environment to keep the temperature of the fet in 4

check. The cooling plane is about 3 x 2 cm. It is present on

3 layers: top, bottom, and one internal layer. The remaining

internal layer is reserved for a ground plane. The copper

extends to the edges of the board. The layers are

interconnected by via’s. See Figure 3. The red area is the

copper plane on the top copper. This copper plane is a bit

overkill for applications that do not require 90 W or more.

Figure 3. Copper Plane

Erratum

Boards with version «ncl31000as» and date

«25/03/2021» had a mistake in the arduino pinout. Headers

J6 and J7 are swapped in the layout and do not correspond

with the correct arduino placement. Modifications have

been made to these connectors so that the board can still be

plugged on top of an arduino mcu. 5 pins have been cut and 3

connections rewired.

Because of this patch the arduino shield fits an arduino

microcontroller board and it can be used as expected except

for the PWM1 pin which is not available due to this patch.

EVBUM2798/D

www.onsemi.com

SCHEMATIC

100 k

VBB

M2G

TP6

VBB

100 n

100 V

GND

VBB1

100 n

100 V

22 F

100 V

VINP 280  @ 100 MHz

L 1

TP4

VINP

100 m 1% 3 W

R11

SVSS SGND

PSNSN_CH1

PSNSP_CH1

TP7

L 2 VBB_LED

DC IN

56 F

80 V

VSS

8  @ 100 MHz VBB_LED

IORE F

NR ST

VI N

A 1

A 3

A 4

A 5

Power

Analog in

SCL

SDA

AVDD

GND

SCK/DAC

MISO

MOSI

GND

T P3 NC

T P2 NC

T P1 NC

VDD 2

A 0

A2/D A C

INTB

VDD1_ E X T

D10

D11

D12

D13

D14

D15

PWM2

PWM1

PWMVLC

CS1

CS2

ADIM1

ADIM2

*SB 2

TP57

GND

TP58

GND

TP59

GND

SCL

SDA

ADI M1

Reverse polarity protection + overvoltage protection

Arduino headers Board pin−out Arduino pin−out

GND

5VOUT

3V3OUT

RST

100 k

33 k

VDD1

LED_FAULT L ED_POE

DEVDET

ADIM1

INTB

INT#

DIO13

DIO14

DIO12

DIO3

DIO2

DIO1

DIO0

DIO6

DIO5 SCL

SDA

GND

910

1112

1314

1516

RSL10

VDD2

*SB1

PWMVLC

ADIM2

PWM1

RSL10 headers

VDD1

39 k

R16

VDD1VDD2

LED4

/INT

390 E

R1 5

L E D1

3V3

L E D3

FAULT

LED_FAULT

2.2 k

R1 2

1 k

R1 3

2.2 k

R1 4

L E D2

Status

GND GND GND

INTB

GND GND

R44

2 3

2N7002W T1G

2 3

2N7002WT1G

100 k

R 9

10 k

R1 0

VDD1

INT#

33 k

R 8

VCC

SCL

SDA 5

7VSS 4

CAT24C512WI−GT3

GND

16V

GND

VDD 1

GND

SCL

SD A

GND GND GND

1 

16 V

1 

Strata EEPROM & HOT PLUG Detection

Pulse INT# on plug event

34 k, 1 F = 50 ms negative pulse

System can also mask INT# for level based interrupt.

Pull gate of first FET low to disable pulse INT# events.

Headers J6 and J7 are swapped in the layout

and do not correspond with the correct arduino

placement. Modifications have been made to

these connectors so that the board can still be

plugged on top of an arduino mcu. The PWM1

pin is not available due to this patch.

EVBUM2798/D

www.onsemi.com

ADIM + VLC

UVLO

CADC

VREF

P9V

PWM

AD1/CSB

SDA/MOSI

SCL/CLK

INTB

DIM

AD2/MISO

P9V

U4B

10 n

C20

GNDGNDGND

16 V

C17

GND

100 n

25 V

C18

10 V

C19

TP23

VREF

TP22

P9V TP24

CADC

VRE

DIM

P9V

PWM _PIN

UVLO

CADC

INT_PIN

SDA/MOSI

SCL/CLK

ADDR1/ CSB

ADDR2/MISO

BAT54ALT1G

GND GND

SCL

SDA

MOSI

BAT54ALT1G

GND

R26 100E

100E

R25

4k7

R22

4k7

R21

VDD1

SCK/DAC

CS1

JP2

PWMEN

VDD1

MISO

INTB

PWM1

100ER28

100E

R29

100E

R30

100E

R27

47 k

R35

130k

R34

VSS

100 k

ANADIM

GND

VRE

VBB

GND

100 n

25 V

C11

GND

10 V

C12

VCC

GND 3

NL 17SZ 125DFT 2G

10 k

R17

10 k

R19

50 V

4 n7n

C14

16 V

C13

GNDGND

TP9

PWM_VLC

4k7

R18

2 k

R20

TP11

TP10

TP15

VRE

TP8

PWM_DIM

UVLO:VBB < 20 V

PWMVLC

ADIM1

TP19

UVLO

MCUDAC

ADIM _POT M

ADIM

MCUDAC

ADI M POTM

ADI M

GND

1 k

R31

MCUDAC SEL

iSN

SCK/DAC

A2/DAC

TP21 DIM

GND

VDD1

10 k

R32

SB3

SB4

1 n

100 V

C15

J8A

3 4

J8B

J8C

DIMSEL

T P14 A D1/C S

T P12 SDA /M OSI

T P13 SC L /C L K

T P16 A D2/M ISO

T P17 INT

T P18 PW M

0ER45

R46

R47

R48

620k

R49

100 V

1 n C10

VSS

R23

2.2 

1 

2.2



1 

L 6

100 μH

VDD2GB

VDD2 SW

IVDD 2

VDD2 sns

GND

6V3

C39

6V3

C41

GND

TP35

VDD2

GND

0.75 E

R41

390 μH

IVDD1

3V3 inp NCL31001

VDDsns

FDC86 02

Q8A

GND

VDD1SW

VDD1GB

GND

6V3

C38

6V3

C40

TP34

VDD1

VDD2

VBB

VSS

PSNSN

PSNSP

GND

N3V3

VBB

U4A

U4E

16 V

C25

VSS

GND

N3V3

PSNSP_CH1

PSNSN_CH1

VDD1_ EXT

*SB9

VBB_LED

470 n

10 V

C16

1 

22 22 

47 F47 F

D10

NSPM0051MUT5G

DCDC

VBB_L

E D

10 n

25 V

C23

GND

L 9

TP30

LDSNSP

TP31

LDSNSN

TP27

VG T

TP26

VGB

160E

R3 6

GND GND

T P33

VL E D+

50 V

10 n

C21

LDSW VL E D+

VL E D−

LDGT

LDGB

100 m

1 W

R40

TP28

VSW

GND

33E

R38

L 7

L 8

L 4

74479876124C

4.7 n

100 V

C37

150 p

100 V

C29

GND

L DC M P

LDSNSN

LDSNSP

TEMP

VLED

iSN

i SN

470n

100V

C3 1

470n

100V

C3 2

470n

100V

C2 4

470n

100V

C3 4

FDM A037N0 8L C

VBB_L

E D

GND

470 p

100 V

C36

GND

470 p

100 V

C35

TP25

LDCMP

TP36

LED+

TP37

LED−

10 k

R39

20 k

R37

GND

BST

50 V

10 n

C22

BAS21AHT1G

NVT FS6H8 88N

BAS21AH

T 1G

GND

GND GND

100 n

100 V

C28

1 2

Rt1

NCP18WF104F12RB

Measure temperature top fet copper plane − Multimeter

TP32

Tfet

TP29

TEMP

100 k

R43

VREF

Measure temperature top fet copper plane

100 n

100 V

C33

iHV

1 2

L 3

7447709470

400 n

100 V

C26

470 n

100 V

C27

A2 J3

LED

A2 J9

TLED

GND

Rt2

NCP18WF104F12RB

GND

R24

R33

LDGT

BST

LDSW

LDGB

VLED

LDSNSP

LDSNSN

TLED

LDCMP

110  @ 100 MHz

LED Driver

EVBUM2798/D

www.onsemi.com

Table 1. BILL OF MATERIAL

Qty Designator Manufacturer Part No. Value Footprint Description

1 D1 ON Semiconductor MMSZ5245BT1G ONSC−SOD−123−2−42

5−04_V

Zener Voltage Regulator, 500 mW,

2−Pin SOD−123, Pb−Free,

Tape and Reel

1 J1 Samtec SSQ−108−03−F−SSSQ−108−03−X−SBoard−To−Board Connector,

2.54 mm, 8 Contacts, Receptacle,

Through Hole, 1 Rows

1 J2 Samtec SSQ−106−03−G−SSSQ−106−03−X−SBoard−To−Board Connector,

2.54 mm, 6 Contacts, Receptacle,

Through Hole, 1 Rows

1 J3 Weidmueller 1862960000 SC_SMT_3_81_90G_0

OMNIMATE Signal − series

BC/SC 3.81

1 J4 61201621721 61201621721 Male Box Header WR−BHD, THT,

Angled, pitch 2.54 mm, 16 pins

1 J5 Weidmueller 1862960000 SC_SMT_3_81_90G_0

OMNIMATE Signal − series

BC/SC 3.81

1 J6 Samtec SSQ−110−03−G−SSSQ−110−03−X−SBoard−To−Board Connector,

2.54 mm, 10 Contacts,

Receptacle, Through Hole,

1 Rows

1 J7 Samtec SSQ−108−03−G−SSSQ−108−03−X−SBoard−To−Board Connector,

2.54 mm, 8 Contacts, Receptacle,

Through Hole, 1 Rows

1 J9 Weidmueller 1862960000 SC_SMT_3_81_90G_0

OMNIMATE Signal − series

BC/SC 3.81

1 L3 7447709470 WE−PD−XXL SMD−Shielded Power Inductor

WE−PD, L = 47.0 H

1 L4 Wurth Electronics 74479876124C SMD 0806 Power Multilayer Inductor

WE−PMI, L = 0.24 H

1 L5 Wurth Electronics 744777239 WE−PD 7345 SMD−Shielded Power Inductor

WE−PD, L = 390 H

1 L6 Wurth Electronics 7447714101 WE−PD 1050 SMD−Shielded Power Inductor

WE−PD, L = 100 H

1 U1 CAT24C512WI−GT3 FP−751BD−01−IPC_C IC EEPROM 512K I2C 1 MHZ

8SOIC

1 U2 ON Semiconductor NL17SZ125DFT2G FP−419A−02−MFG IC BUFFER NON−INVERT 5.5 V

SC88A

1 U4 ON Semiconductor NCL31000 485EP

2D8, D9 ON Semiconductor BAS21AHT1G ONSC−SOD−323−2−47

7−02_V

Low Leakage Switching Diode,

2−Pin SOD−323, Pb−Free,

Tape and Reel

2Q4, Q5 ON Semiconductor 2N7002WT1G ONSC−SC−70−3−419−

04_V

Small Signal MOSFET, 60 V,

340 mA, Single, N−Channel, 3−Pin

SC70, Pb−Free, Tape and Reel

2Rt1, Rt2 NCP18WF104F12RB FP−NCP18−0_15−IPC_

NTC Thermistor for Temperature

Sensor, 0603, 100 kO, 1%,

0.032 mA, 5 V

3D5, D6, D7 ON Semiconductor BAT54ALT1G ONSC−SOT−23−3−318

−08_V

Schottky Barrier Diodes, 3−Pin

SOT−23, Pb−Free, Tape and Reel

5SB1, SB2,

SB3, SB4,

SB9

1005−SB−2Solder bridge

5R5, R7,

R33, R46,

R47

CRG0603ZR OE RESC1608L Resistor

1 R42 RL1220S−R20−F 0.2E RESC2012N Resistor

EVBUM2798/D

www.onsemi.com

Table 1. BILL OF MATERIAL (continued)

1R41 RCWE0603R750FKE

0.75E RESC1608N Resistor

2R13, R31 CRGCQ0603F1K0 1 k RESC1608L Resistor

1 C10 TDK CGA3E2X7R2A102M

080AA

1 n CAPC1608L Capacitor

1 C15 TDK CGA3E2X7R2A102M

080AA

1 n CAPC1608L Capacitor

5C3, C5,

C13, C17,

C25

TDK C1608X7R1C105K08

0AC

1 CAPC1608L Capacitor

1 R44 Harwin D3082−05 2 pins Groundbar D3082−05 2 (1 x 2) Position Shunt Connector

Non−Insulated 0.400 (10.16 mm)

Gold

1 R20 CPF0603F2K0C1 2 k RESC1608L Resistor

2R12, R14 CRGCQ0603F2K2 2.2 k RESC1608L Resistor

1 C12 TDK C2012X7R1C225K12

5AB

2.2 CAPC2012N Capacitor

1 C19 TDK C2012X7R1C225K12

5AB

2.2 CAPC2012N Capacitor

1 J8 Wurth Electronics 61300621121 2.54 mm THT

Dual Pin

Header, 6p

61300621121 Board−To −Board Connector,

Vertical, 2.54 mm, 6 Contacts,

Header, WR−PHD Series,

Through Hole

3R18, R21,

R22

CRG0603F4K7 4k7 RESC1608L Resistor

1 C14 TDK CGA3E2X7R1H472

M080AA

4.7 n CAPC1608L Capacitor

1 C37 TDK C1608X7R2A472K08

0AA

4.7 n CAPC1608L Capacitor

1 L2 Wurth Electronics 7427922808 8  @

100 MHz

WE−MPSB_0603 WE−MPSB EMI Multilayer Power

Suppression Bead, size 0603,

8  @ 100MHz

5R10, R17,

R19, R32,

R39

CRGCQ0603F10K 10 k RESC1608L Resistor

3C20, C21,

C22

TDK CGA3E2X7R1H103K

080AA

10 n CAPC1608L Capacitor

1 R37 CPF0603F20KC1 20 k RESC1608L Resistor

2C38, C40 KEMET C1206C226K9PACT

22 CAPC3216N Capacitor

1 C6 Nichicon UVR2A220MED 22 FCAPPR2.5−6.3x11 Capacitor

1 D10 ON Semiconductor NSPM0051MUT5G 30 kV ESD

70 A 8/20 s

Surge

Case 517CZ Transient Voltage Suppressors

1 R38 CRGCQ0603F33R 33E RESC2012L Resistor

2R4, R8 CRGCQ0603F33K 33 k RESC1608L Resistor

1 R16 CRGH0603F39K 39 k RESC1608L Resistor

1 R35 CRGCQ0603F47K 47 k RESC1608L Resistor

2C39, C41 KEMET C1210C476M9PAC 47 FCAPC3225N Capacitor

1 C7 KEMET A759MS566M1KAAE

045

56 FCAPPR5−10x12.5 Capacitor

1 Q6 ON Semiconductor NVTFS6H888N 80 V, 13 A,

55 m

MKT−MLP08T Power MOSFET 80 V, 55 m, 13 A,

Single N−Channel

1 Q7 FDMA037N08LC 80 V, 6 A,

36.5 m

Case 511DB MOSFET FET 80 V 3.7 M

MLP33

EVBUM2798/D

www.onsemi.com

Table 1. BILL OF MATERIAL (continued)

4R25, R26,

R29, R30

CRGCQ0603F100R 100 E RESC1608L Resistor

1 P1 Vishay TS53YJ103MR10 100 k TS53YJ 5 mm Square Surface Mount

Miniature Trimmers Single−Turn

Cermet Sealed 5 K 250 mW

35.4 V 20%

5R1, R2, R3,

R9, R43

CRGCQ0603F100K 100 k RESC1608L Resistor

1 R40 LVM25FVR100E−TR 100 m RESC6332N Resistor

1 R11 CRA2512−FZ−R100

ELF

100 m 1%

RESC6332N Resistor

3C11, C18,

C23

AVX 06033C104KAT4A 100 n CAPC1608L Capacitor

4C8, C9,

C28, C33

TDK C2012X7R2A104K12

5AA

100 n CAPC2012L Capacitor

www.onsemi.com

onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates

and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A

listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi is an Equal Opportunity/Affirmative Action Employer. This

literature is subject to all applicable copyright laws and is not for resale in any manner.

The evaluation board/kit (research and development board/kit) (hereinafter the “board”) is not a finished product and is not available for sale to consumers. The board is only intended

for research, development, demonstration and evaluation purposes and will only be used in laboratory/development areas by persons with an engineering/technical training and familiar

with the risks associated with handling electrical/mechanical components, systems and subsystems. This person assumes full responsibility/liability for proper and safe handling. Any

other use, resale or redistribution for any other purpose is strictly prohibited.

THE BOARD IS PROVIDED BY ONSEMI TO YOU “AS IS” AND WITHOUT ANY REPRESENTATIONS OR WARRANTIES WHATSOEVER. WITHOUT LIMITING THE FOREGOING,

ONSEMI (AND ITS LICENSORS/SUPPLIERS) HEREBY DISCLAIMS ANY AND ALL REPRESENTATIONS AND WARRANTIES IN RELATION TO THE BOARD, ANY

MODIFICATIONS, OR THIS AGREEMENT, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING WITHOUT LIMITATION ANY AND ALL

REPRESENTATIONS AND WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, NON−INFRINGEMENT, AND THOSE ARISING FROM A

COURSE OF DEALING, TRADE USAGE, TRADE CUSTOM OR TRADE PRACTICE.

onsemi reserves the right to make changes without further notice to any board.

You are responsible for determining whether the board will be suitable for your intended use or application or will achieve your intended results. Prior to using or distributing any systems

that have been evaluated, designed or tested using the board, you agree to test and validate your design to confirm the functionality for your application. Any technical, applications or

design information or advice, quality characterization, reliability data or other services provided by onsemi shall not constitute any representation or warranty by onsemi, and no additional

obligations or liabilities shall arise from onsemi having provided such information or services.

onsemi products including the boards are not designed, intended, or authorized for use in life support systems, or any FDA Class 3 medical devices or medical devices with a similar

or equivalent classification in a foreign jurisdiction, or any devices intended for implantation in the human body. You agree to indemnify, defend and hold harmless onsemi, its directors,

officers, employees, representatives, agents, subsidiaries, affiliates, distributors, and assigns, against any and all liabilities, losses, costs, damages, judgments, and expenses, arising

out of any claim, demand, investigation, lawsuit, regulatory action or cause of action arising out of or associated with any unauthorized use, even if such claim alleges that onsemi was

negligent regarding the design or manufacture of any products and/or the board.

This evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC,

CE or UL, and may not meet the technical requirements of these or other related directives.

FCC WARNING – This evaluation board/kit is intended for use for engineering development, demonstration, or evaluation purposes only and is not considered by onsemi to be a finished

end product fit for general consumer use. It may generate, use, or radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant

to part 15 of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this equipment may cause interference with radio

communications, in which case the user shall be responsible, at its expense, to take whatever measures may be required to correct this interference.

onsemi does not convey any license under its patent rights nor the rights of others.

LIMITATIONS OF LIABILITY: onsemi shall not be liable for any special, consequential, incidental, indirect or punitive damages, including, but not limited to the costs of requalification,

delay, loss of profits or goodwill, arising out of or in connection with the board, even if onsemi is advised of the possibility of such damages. In no event shall onsemi’s aggregate liability

from any obligation arising out of or in connection with the board, under any theory of liability, exceed the purchase price paid for the board, if any.

The board is provided to you subject to the license and other terms per onsemi’s standard terms and conditions of sale. For more information and documentation, please visit

www.onsemi.com.

PUBLICATION ORDERING INFORMATION

TECHNICAL SUPPORT

North American Technical Support:

Voice Mail: 1 800−282−9855 Toll Free USA/Canada

Phone: 011 421 33 790 2910

LITERATURE FULFILLMENT:

Email Requests to: [email protected]

onsemi Website: www.onsemi.com

Europe, Middle East and Africa Technical Support:

Phone: 00421 33 790 2910

For additional information, please contact your local Sales Representative