Musical Fidelity CD Pre Specification

Brand: Musical Fidelity

Model: CD Pre

Type: Specification

This manual is also suitable for

Issue 1: January 2002 CD Pre Instructions for Use. Page 1of 19

LINE 1 LINE 2 LINE 3

DIGITAL 1 DIGITAL 2 CD

DIGITAL

MONITOR TAPE

MONITOR

POWER

LANGUAGE

PLAY/PAUSE

STOP

OPEN/CLOSE

CD Pre

COMBINATION CD PLAYER AND

DIGITAL / ANALOGUE PRE-AMPLIFIER

INSTRUCTIONS FOR USE

Thank you for purchasing the Musical Fidelity CD Pre.

Used properly and carefully, it should give many years of outstanding

musical reproduction.

The CD Pre uses the latest 24 Bit DAC technology and jitter reduction

techniques to achieve both an excellent technical specification and

unparalleled sound quality.

Æsthetically, the CD Pre is a perfect match for the A3 FM tuner and

A3 amplifier or A300 integrated amplifier.

Together these components form one of the finest hi-fi systems available.

Dust regularly with a soft duster or soft brush but be careful when using

cleaning or polishing agents - they may harm the surface finish.

If you have any questions about your audio system,

please consult your dealer who is there to help and advise.

CD Pre Instructions for Use. Page 2of 19

CONTENTS

PAGE

3Safety Information: -Mains plug (U.K. only)

-Modification warning

4Safety Information: -Warnings

(continued)

5User Information: -Radio-frequency interference

6General Advice: -Installation precautions

-User information

7Remote Control: -Use and illustration

8Facilities and -Front and rear panel illustrations

Connections:

9Interconnection and -Interconnection procedure

Pre-amp operation: -Switching on

-Input source selection

10 Pre-amplifier, -Mute function

Operation: -Line input monitoring

-Tape recording

11 CD Player, -Loading and playing discs

Basic Operation: -Pause

-Index points

12 CD Player, -Track selection

Basic Operation: -Search

-Displaying playback time

13 CD Player, -Repeat playback

Special Features: -A-B repeat playback

-Shuffle playback

14 CD Player, -Introduction search

Special Features: -Programmed play

-Random Music Selection

15 CD Player, -Programmed play - continued

Special Features: -Autospace

-Display on / off

16 CD Text: -CD text discs

17 CD Text: -Other languages

18 Troubleshooting: -Basic problem solving

19 Specifications

Issue 1: January 2002

CD Pre Instructions for Use. Page 3of 19

Issue 1: January 2002

SAFETY

INFORMATION

IMPORTANT! (U.K. only)

This unit is supplied in the U.K. with a mains lead fitted with a moulded 13 amp plug.

If, for any reason, you need to cut off the plug, please remove the fuse holder and dispose of

the plug safely, out of reach of children. It must not be plugged into a mains outlet.

The wires in the mains lead supplied with this appliance are coloured in accordance

with the following code:

Green and yellow..............Earth

Blue................................Neutral

Brown................................Live

WARNING - This appliance must be earthed

As the colours of the wires of the mains lead of this appliance may not correspond with the

coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug

which is marked with the letter E or coloured green or green-and-yellow, or by the earth

symbol:

The wire which is coloured brown must be connected to the terminal which is marked with the

letter L or coloured red.

The wire which is coloured blue must be connected to the terminal which is marked with the

letter N or coloured black.

If connecting to a BS1363 plug, a 13 amp fuse must be used.

WARNING:

ANY MODIFICATIONS TO THIS PRODUCT NOT EXPRESSLY

APPROVED BY MUSICAL FIDELITY WHO IS THE PARTY

RESPONSIBLE FOR STANDARDS COMPLIANCE COULD VOID

THE USER'S AUTHORITY TO OPERATE THIS EQUIPMENT.

CD Pre Instructions for Use. Page 4of 19

WARNINGS

Issue 1: January 2002

CLASS 1 LASER PRODUCT

This CD player has been designed and manufactured according to FDA regulations "title 21,

CFR, chapter 1, subchapter J, based on the Radiation Control for Health and Safety Act of

1968", and is classified as a Class 1 laser product. There is no hazardous radiation during nor-

mal use because invisible radiation emitted inside this product is completely confined within

the protective housing. However you must observe the following important warnings:

CAUTION !

•THIS CD PLAYER USES INVISIBLE LASER LIGHT. WHEN THE PLAYER

OPERATES, LASER LIGHT IS RADIATED INTERNALLY.

DO NOT REMOVE THE PROTECTIVE HOUSINGS.

•USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS

RADIATION EXPOSURE CAUSING EYE INJURY.

•IF THIS PRODUCT DEVELOPS A FAULT, PLEASE CONTACT YOUR AUTHORISED

MUSICAL FIDELITY SERVICE AGENT. DO NOT ATTEMPT TO SERVICE IT YOUR-

SELF AND DO NOT CONTINUE TO USE THIS PRODUCT IN A FAULTY STATE.

WARNING AND INFORMATION LABELS:

THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR,

CHAPTER 1, SUBCHAPTER J, PART 1040 AT DATE OF MANUFACTURE.

THIS PRODUCT COMPLIES WITH PART 15 OF THE FCC RULES.

OPERATION IS SUBJECT TO TWO CONDITIONS:

1THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

2THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING

INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

CAUTION - INVISIBLE LASER RADIATION WHEN OPEN AND

INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.

VORSICHT! - UNSICHTBARE LASERSTRAHLUNG TRITT AUS,

WENN DECKEL GEÖFFNET UND WENN

SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT IST

NICHT DEM STRAHL AUSSETZEN!

VARNING - SYNLIG LASERSTRALNING NÄR DENNA DEL

ÄR ÖPPNAD OCH SPÄRR AR URKOPPLAD.

STRALEN AR FARLIG.

ADVARSEL - USYNLIG LASERSTRALING VED ABNING, NAR

SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION.

UNDGA UDSÆTTELSE FOR STRALING.

VAROITUS! - SUOJAKOTELOA EI SAA AVATA. LAITE SISÄLTÄÄ

LASERDIODIN, JOKA LÄHETTÄÄ (NÄKYMÄTONTÄ)

SILMILLE VAARALLISTA LASERSÄTEILYÄ.

FITTED INTERNALLY

TO BASE OF CHASSIS

CLASS 1

LASER PRODUCT

LINE1 LINE 2 LINE 3

ANALOGUE

INPUTS TAPE

MONITOR TAPE OUT PRE OUT

DIGITAL INPUTS

COAXIAL

1 2

DIGITAL INPUTS

OPTICAL DIGITAL

MONITOR

DIGITAL

OUTPUTS

COAXIAL OPTICAL

MOUNT UNIT ON SOLID SURFACE. DO NOT REMOVE SCREWS OR

COVERS UNDER ANY CIRCUMSTANCES. NO USER SERVICEABLE

COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED ENGINEER.

SEE OWNERS MANUAL FOR FURTHER INFORMATION.

THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR, CHAPTER 1, SUBCHAPTER J, PART 1040 AT DATE OF MANUFACTURE.

THIS PRODUCT COMPLIES WITH PART 15 OF THE FFC RULES. OPERATION IS SUBJECT TO TWO CONDITIONS: -

1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

CAUTION

THIS APPLIANCE

MUST

BE EARTHED

SERIAL

NUMBER:

DATE OF

MANUFACTURE

MUSICAL FIDELITY CD PRE

2 4

MANUFACTURED BY MUSICAL FIDELITY LTD. 15-17 OLYMPIC TRADING ESTATE, FULTON ROAD,

WEMBLEY, MIDDLESEX, HA9 OTF, ENGLAND

POWER COMSUMPTION 22W

CD Pre Instructions for Use. Page 5of 19

Issue 1: January 2002

USER INFORMATION

RADIO - FREQUENCY INTERFERENCE (RFI)

This equipment uses and can radiate radio frequency energy, and if not installed and operated in

accordance with the instructions, may cause interference to radio communications and other

electronic equipment.

However, it is designed to minimise RFI, and accordingly been tested to North American stan-

dards (FCC regulations - limits for a class B digital device persuant to part 15 of the rules).

These requirements are intended to provide reasonable protection against excessive interference

in a residential installation.

Conversely, the product has also been checked to ensure that its own operation is not adversely

affected by normal background levels of RFI received externally.

However, if interference is experienced, for instance to radio or TV broadcasts, the user is rec-

ommended to try one or more of the following measures:

• Identify the source of interference by turning off power to the CD Pre or other

equipment individually, and checking whether the problem then disappears.

• Re-orientate or relocate the receiving aerial.

• Move the CD Pre away from the receiver.

• Connect the CD Pre to a mains outlet on a different circuit from the receiver.

• Consult a dealer or experienced TV/radio technician for help.

If a problem persists, please contact Musical Fidelity's service department.

Issue 1: January 2002 A3 CD Instructions for Use. Page 6of 15

GENERAL ADVICE

INSTALLATION PRECAUTIONS AND USER INFORMATION

Your CD Pre is designed and built to provide trouble-free performance, but as with all

electronic devices it is necessary to observe a few precautions:

* Note all warnings shown on the back of the unit.

* Only connect the CD Pre to a mains outlet having the same voltage as marked on the back of

the unit.

* Always switch off the mains supply before before connecting or disconnecting your audio

equipment.

* Position the mains lead and signal interconnects where they are not likely to be walked on or

trapped by items placed on them.

* Do not use near water, or place water-filled containers on the pre-amplifier, for example

flower vases or potted plants. If water does spill into the equipment, immediately pull out

the mains plug from the wall socket and inform your dealer, who should then check the

unit before further use. Entry of liquid into the pre-amplifier is dangerous, and may cause

electric shock or fire hazard.

* Do not place the unit near heat sources such as radiators, direct sunlight or above other

equipment which becomes warm with use. Do not obstruct ventilation slots.

* Do not remove any covers or try to gain access - refer all service work to an authorised

Musical Fidelity agent. There are no internal user adjustments.

NOTE: Unauthorised opening of the equipment will invalidate any warranty claims.

* There are fuses inside this product. In the unlikely event that one blows, refer the unit to

your audio dealer.

Do NOT try to replace the fuse yourself as this will invalidate the warranty.

* Dust regularly with a soft duster or soft brush. For more thorough cleaning of the cabinet and

remote control, use a moist cloth. We do not recommend the use of solvents such as white

spirit or thinners, as they could damage the surface finish.

* The electronics in modern hi-fi equipment is complex and may, therefore, be adversely

affected or damaged by lightning. For protection of of your audio system during electrical

storms, remove the mains plugs and disconnect any aerial lead.

* If after-sales service is required, to help your dealer identify the CD Pre, please quote the

serial number located on the rear panel of the unit.

CD Pre Instructions for Use. Page 7of 19

REMOTE CONTROL

Issue 1: January 2002

REMOTE CONTROL

The remote control enables most functions of the pre-amplifier to be operated from a conven-

ient distance.

Equivalent buttons on the remote handset have the same functions as the those on the front

panel of the unit.

Some operations are only available via the handset.

As the remote control uses an invisible infra-red light beam, the transmitter must be pointed

directly towards the receiver window on the front of the pre-amplifier, without visual obstruc-

tion between them.

If the range of the remote control greatly decreases, replace the batteries with new ones.

Do not mix old and new batteries - four are required, type SUM-4, AAA or LR03.

OPEN / CLOSE CD tray PLAY / PAUSE

to start, pause or

resume CD playback.

CD direct track access buttons.

CD special feature buttons

- see pages 13 to 15.

STOP to stop CD playback.

VOLUME up / down

SEARCHbuttons to scan

CD forwards or backwards

TRACK back/forwards buttons

Input source selector buttons

MUTE button

MONITOR buttons

- see page 10

CD Pre Instructions for Use. Page 8of 19

Issue 1: January 2002

FACILITIES AND CONNECTIONS

LINE1 LINE 2 LINE 3

ANALOGUE

INPUTS TAPE

MONITOR TAPE OUT PRE OUT

DIGITAL INPUTS

COAXIAL

1 2

DIGITAL INPUTS

OPTICAL DIGITAL

MONITOR

DIGITAL

OUTPUTS

COAXIAL OPTICAL

MUSICAL FIDELITY CD PRE

2 4

MANUFACTURED BY MUSICAL FIDELITY LTD. 15-17 OLYMPIC TRADING ESTATE, FULTON ROAD,

WEMBLEY, MIDDLESEX, HA9 OTF, ENGLAND

LINE 1 LINE 2 LINE 3

DIGITAL 1 DIGITAL 2 CD

DIGITAL

MONITOR TAPE

MONITOR

POWER

LANGUAGE

PLAY/PAUSE

STOP

OPEN/CLOSE

7DIGITAL 1 input selector button and LED

8Digital monitor LED (see page 10)

9DIGITAL 2 input selector button and LED

10 POWER mains on/off switch

11 Tape monitor LED (see page10)

12 CD input selector button and LED

13 CD LANGUAGE button (see page 17)

14 PREVIOUS CD track button

15 CD drawer

16 CD drawer OPEN / CLOSE button

17 CD STOP button

18 Volume control knob with LED

19 LINE INPUT 1 - analogue

- left and right

20 LINE INPUT 2 - analogue

- left and right

21 LINE INPUT 3 - analogue

- left and right

22 TAPE MONITOR

- analogue, left and right

REAR PANEL

23 TAPE OUTPUT - analogue

- left and right (see page 10)

24 LINE OUTPUT - analogue

left and right (to amplifier)

25 INPUT 1 - digital co-axial

26 INPUT 2 - digital co-axial

27 INPUT 1 - optical

28 INPUT 2 - optical

29 DIGITAL MONITOR

- digital co-axial

30 LINE OUTPUT

- digital co-axial

31 LINE OUTPUT

- optical

19 20 21 22 23 24 25 26 27 28 29 30 31

7 9 11 13 14 15 16 17 18

8 10 12

1 2 3 4 5 6

FRONT PANEL

1LINE 1 input selector button and LED

2LINE 2 input selector button and LED

3LINE 3 input selector button and LED

4 NEXT CD track button

5 Display (incorporates infra-red

remote control receiver)

6 CD PLAY / PAUSE button

IEC type mains inlet socket

MUSICAL FIDELITY

BEFORE CONNECTING . . . . . . .

Ensure that mains power to the various

components of your audio system is

switched off. Please note that audio con-

necting leads are not supplied with this

product.

OUTPUT CONNECTION

The CD Pre should be connected to an ana-

logue amplifier input by audio cables with

RCA/phono type plugs. These link the left

and right PRE OUT sockets on the rear

panel of the CD Pre to corresponding line

input sockets on the amplifier. Do not use

any sockets on the amplifier intended for

“vinyl” phono cartridge input, as the sensi-

tive circuit will overload, producing a

severely distorted sound.

Alternatively, the DIGITAL OUTPUTS

(coaxial or optical) can be used for connec-

tion to suitable digital equipment.

All three types of output can be used for

feeding different equipment at the same

time, if required.

Note that the volume control only affects

analogue audio line output to the amplifier,

not digital or tape outputs.

INPUT CONNECTION

Analogue inputs are provided for three ana-

logue line sources, and two digital (optical

or co-axial).

Do not connect both co-axial and optical

leads to the same input.

Connect digital or optical input leads from

the other audio sources in your system as

required.

The internal D-to-A convertor will also han-

dle digital data from an external CD or

DVD audio source.

MAINS POWER CONNECTION

Insert the accessory IEC mains lead plug

into the rear panel socket, and then the other

end into a convenient wall outlet.

SWITCHING ON

Before applying mains power to other audio

components, check that the volume control

setting on the CD Pre is low (knob turned

anticlockwise).

Press the power switch, and the front panel

display will light to confirm that the unit is

ready for use.

INPUT SOURCE SELECTION

Choose the required input source either by

pressing the front panel function buttons or

corresponding buttons on the remote control

marked LINE 1, 2 or 3, or DIGITAL 1 or 2.

The appropriate front panel LED will then

light to confirm your selection.

In the case of digital inputs, if no digital

data is being received at the selected input

socket, the associated LED will flash instead

of remaining constant.

Turn the volume control to obtain the pre-

ferred level of sound.

CD Pre Instructions for Use. Page 9of 19

Issue 1: January 2002

CONNECTIONS & PRE-AMPLIFIER OPERATION

PRE-AMPLIFIER OPERATION

MUTE (Remote Control Only)

Pressing the MUTE button once on the

remote control will interrupt analogue out-

put to the amplifier. Pressing MUTE again

will restore audio output. The LED in the

volume control knob then goes off to indi-

cate that the outputs are muted.

This function does not affect tape monitor

or digital outputs.

If the CD Pre is powered off while still

muted, the effect will be cancelled when

next switched on.

DIGITAL MONITORING

(Remote Control Only)

Any selected input source can be monitored

with suitable external equipment from the

digital co-axial and/or optical output sock-

ets.

A digital input source (co-axial only) can be

monitored by pressing DIGITAL MONI-

TOR on the remote control. This does not

affect the selected input source, which will

still be available from the tape or digital

outputs.

This feature may be used together with a

digital output to connect to a computer

sound card or CD recorder, providing it has

digital inputs and outputs.

If the selected input source is digital (CD or

DVD audio formats only) a converted ana-

logue signal will also be available at the

tape output sockets.

Note that with this arrangement the CD

Pre’s volume control has no effect.

TAPE MONITOR (Remote Control Only)

The CD Pre can be used in analogue mode

for off-tape monitoring from 3-head tape

decks.

This allows the user to compare the original

sound with the recorded version while the

recording is being made.

In this case, the recorder’s left- and right-

hand line output sockets should be connect-

ed to the CD Pre’s tape input, and the

recorder’s line input sockets to the CD Pre’s

tape output sockets.

To record, simply select the required source

with the appropriate button on the CD Pre’s

front panel or from the remote control.

Pressing TAPE MONITOR on the remote

control will allow you to monitor what is

being recorded, and the matching blue LED

on the front panel will light to confirm oper

ation. Press TAPE MONITOR again to

cancel this mode.

On some 3-head tape decks, there is an addi

tional “tape / source” switch which should

be in the “tape” position for this arrange-

ment to function. If in doubt, refer to the

recorder’s user manual, or consult your

dealer.

CD Pre Instructions for Use. Page 10 of 19

Issue 1: January 2002

CD Pre Instructions for Use. Page 11 of 19

Issue 1: January 2002

CD - BASIC OPERATION

LOADING AND PLAYING

COMPACT DISCS

If mains power to the CD Pre is switched

on with a disc already loaded, it will auto-

matically search for the disc and begin

playing from the first track. However,

playback will not be audible if the input

has previously been set to another source

before being switched off. The CD button

must therefore be pressed first.

If no disc is loaded, after about 3 or 4 sec-

onds the unit will display the following:

To play a disc, press the OPEN/CLOSE

button to open the transport drawer.

When the drawer is fully extended, insert

the required disc with the label facing

upwards and then press either the

OPEN/CLOSE or PLAY/PAUSE button

to close the transport drawer again.

If OPEN/CLOSE is pressed, the disc

drawer closes and the CD player scans the

contents of the disc. After a short delay, the

display window then shows for approxi-

mately 4 seconds the total number of

tracks available on the CD, and total play-

ing time, for example:

Display time 0on the left then replaces

the temporary track and time information,

indicating that a disc is loaded but not yet

playing.

The “calendar” grid pattern at the right-

hand end of the display also confirms

tracks available for playing up to the first

20, but remains displayed. In the above

example there are 4 tracks on the disc.

DISC PLAY

If PLAY/PAUSE

is pressed, the CD player

will go into play mode, an arrow confirm-

ing playback will appear on the left, and

the current track and index point will be

displayed similar to the following example:

Again, the calendar grid shows playback

progress of the first 20 tracks only.

When all tracks on the CD have been

played, playback stops and the display

reverts to:

PAUSE

Pressing the PLAY/PAUSE

button whilst a

disc is playing pauses playback of the disc.

A pause symbol ( ll ) appears in the display

window next to the play arrow.

The disc will continue spinning but the

track does not advance and the CD Pre’s

output is muted.

Pressing PLAY/PAUSE again resumes

playback from the same place.

INDEX POINTS

Some CDs contain index points within a

track to separate a musical piece into dif-

ferent movements. If used, these index

point numbers (one or two digits, up to 99)

will appear in the display under the INDEX

graphic. Otherwise, index number 1 will

be displayed.

CD Pre Instructions for Use. Page 12 of 19

Issue 1: January 2002

CD - BASIC OPERATION

STOP

Playback can be stopped at any time by

pressing the STOP button once.

TRACK SELECTION

To change track, the track skip buttons

NEXT and PREVIOUS can be pressed

to jump forwards or backwards one track

in either direction. Note that a single press

of the PREVIOUS button restarts play-

back at the beginning of the current track.

A double-press is needed to jump back to

the previous track. Corresponding

TRACK buttons on the remote control are

also marked |<< and >>|. If either button

is held down, the CD Pre will quickly step

through the available tracks in the required

direction.

TRACK SELECTION (Remote control)

A specific track can be selected directly by

pressing the required track number button

on the remote control. The chosen track

then plays immediately.

To play a track number with two digits,

press the 10+ button on the remote control

followed by the first digit, then the second

digit. For example, to obtain track 27,

press 10+ , then 2, then 7.

The SEARCH buttons can be used to fast-

forward or fast-rewind during playback in

a similar way to a video or tape cassette

player. This permits location of particular

passages at high speed with the audio play-

back of the CD still active.

Pressing the forward-search button (>>)

fast winds forwards whilst the search back-

wards button (<<) fast winds backwards.

As the unit searches through a track, the

track time remaining display (far right dig-

its) will be seen to advance rapidly in the

required direction. For both directions the

unit will return to normal playback when

the button is released.

DISPLAYING PLAYBACK TIME

There are three playback time display

modes accessed progressively by pushing

the TIME button on the remote control.

The default mode (e.g. after switch on)

shown below indicates the elapsed time for

the currently playing track (2 minutes

34 seconds in this example):

Pushing the TIMEbutton once changes

the display to show the remaining time for

the current track (4 minutes 29 seconds in

this example):

Pushing the TIMEbutton again changes

the display to show the remaining time for

the whole disc (33 mins 54 secs) below:

(Note: Track and Index displays are not

shown in this mode).

A third press of the TIME button will now

bring the display back to the original

(elapsed track time) mode.

CD - SPECIAL FEATURES

REPEAT PLAYBACK

The REPEAT button on the remote control

allows the repeated playback of either one

track or all tracks on the disc.

By pressing the REPEAT button once, you

can repeat the entire disc (or the pro-

grammed selections - see page 14) over and

over again. Large letters REPEAT briefly

replace track, index and time information

followed by a smaller, permanent REPEAT

legend underneath.

If the REPEAT button is pressed a second

time, only the current track is repeated.

Large letters REPEAT 1briefly replace

track, index and time information followed

by a REPEAT 1 legend underneath.

Pressing REPEAT a third time cancels

repeat mode. Graphics REPEAT OFF then

briefly replace track, index and time infor-

mation before reverting to a normal disc

play display.

A-B REPEAT PLAYBACK

“A-B repeat” provides the option of playing

just a certain section of the disc over and

over again.

Find the beginning of the required section

either by listening, or using the display time

as a guide. When the desired starting point

is reached, press button A/B on the remote

control. The display will show REPEAT and

the flashing letter A.

When the disc has reached the end of the

required section, press the A-B button

again. Letters A-B will now be illuminated

in the display, and the unit continuously

plays the selected part of the disc.

To cancel A-B repeat mode, press REPEAT

on the remote control. Graphics

REPEAT OFF then briefly replace track,

index and time information in the display.

SHUFFLE PLAYBACK

The SHUFFLE feature allows tracks on the

discs to be played in random sequence

rather than the normal consecutive order.

Tracks are also be played in a different order

each time the disc is restarted, or another

disc loaded.

This function is obtained by pressing

SHUFFLE on the remote control with the

unit either stopped or playing.

If playing, the word SHUFFLE in large let-

ters briefly replaces track, index and time

display information, before a permanent red

indication provides a reminder that the func-

tion has been activated.

From stop mode, pressing PLAY/PAUSE

also begins shuffle play.

If the CD Pre is already playing, play will

continue until either the current track has

finished, or either the track >>| button on

the remote control or NEXT on the unit is

pressed. Shuffle play is then further con-

firmed by the track number display digits

briefly changing into segments revolving in

a box formation.

If the SHUFFLE button is now pressed for

a second time, the word CONTINUE briefly

replaces track, index and time display infor-

mation. The unit then resumes normal play

function, except that it now only plays pre-

viously unplayed tracks of the current disc,

unless others are then manually selected.

Shuffle play is cancelled by pressing the

STOP button.

CD Pre Instructions for Use. Page 13 of 19

Issue 1: January 2002

CD - SPECIAL FEATURES

INTRODUCTION SEARCH

The introduction-search function allows

play back of just the start of each track on

the disc, for instance to locate a preferred

track by ear.

Press INTRO on the remote control, and

the display will briefly show:

The first ten seconds (approximately) of

each title on the CD are then played (or the

first 10 seconds of any programmed titles,

see below). The playback arrow in the dis-

play window flashes to indicate that this

mode is activated.

Track playing time can be changed to

approximately 20 or 30 seconds at any time

during introduction mode. Press INTRO

twice or three times in quick succession

instead of once, and the revised time will be

indicated on the display as:

Press STOP to cancel introduction mode.

Note: Intro scan time will be memorised as

long as the unit is powered on, even when

another disc is loaded.

PROGRAMMED PLAY / R.M.S.

The built-in program memory (Random

Music Selection function) allows you to

store up to 24 tracks and then play them

back in the stored order. Each track is

stored as a 'STEP' in the program.

It is possible to store a track more than once

in the same program if required.

Example:- You wish to listen to tracks

14, 7, 9, 9 and 12 in that order on a disc.

With the disc loaded and the player stopped,

first press PROGRAM on the remote con-

trol. The word PROGRAM briefly replaces

track, index and time information, before a

permanent red display provides a reminder

that the function has been activated.

Press the numeric button of the track num-

ber corresponding to the first track you wish

to store (14 in our example is +10, then 4).

That track number will now appear in the

display under TRACK, number 1 (being the

first entry) will appear under STEP, and track

playing time appears under MIN SEC.

Alternatively, the track number can be

selected by using the track skip buttons

( |<< or >>| ).

The calendar grid to the right of the display

also confirms this track selection.

Next the second track to be programmed can

be selected (7 in our example) either by

entering the required number with the

numeric buttons or again by using the track

skip buttons. As the second track number is

selected the step number will be seen to

change to a 2 indicating the program step

being filled.

If you want to save a track twice in succes-

sion (for example 9 followed by 9), then

simply press button 9 twice.

Repeat the above procedure by pressing

remaining track numbers required (9, 9

again and 12 in our example). Note that as

tracks are added, the total playing time indi-

cated increases by a corresponding amount

plus one second per track. This is to allow

access time for the CD mechanism during

the program play sequence.

If entry of more than 24 tracks is attempted

accidently, the memory will not accept the

extra ones. The following is then briefly

displayed:

CD Pre Instructions for Use. Page 14 of 19

Issue 1: January 2002

CD - SPECIAL FEATURES

If at any time you make a mistake or wish

to delete a track from the list, press the

CLEAR button to erase the last step.

Repeated pressing of CLEAR will then

erase each step in reverse order.

If you wish to check the selection before

playing back your program, the CHECK

button can be pressed to step through each

track in turn. At the end of the check

sequence, the display briefly shows:

To play the programmed tracks press

PLAY/PAUSE (or INTRO if required,

see page 14).

When all programmed tracks have been

played, the CD player stops. The same

track selection can then be played again by

pressing the PLAY/PAUSE button.

To cancel this mode, press PROGRAM.

The word CONTINUE then briefly replaces

track, index and time display.

Note: The entire program contents will be

cleared if you open the disc compartment to

load another disc, but this does not cancel

program mode itself.

AUTOSPACE

The CD Pre’s AUTOSPACE function can

be used to insert 4-second silent spaces in

between each track as it is played back.

This can be useful when making cassette

recordings of CDs. Some cassette

recorders feature a track skip or search

function which uses the silent gap between

tracks to locate each one individually.

However, some CDs do not have long

enough gaps between tracks for this function

to operate properly.

AUTOSPACE can solve this problem.

Pressing the AUTOSPACE button once

activates the function. The legend AUTOSPACE

will appear in the display. In this mode,

once the CD Pre has reached the end of a

track the AUTO SPACE graphic will begin to

flash and the elapsed time part of the display

will change to count down from four sec-

onds to zero before play of the next track

begins.

When zero is reached the AUTO SPACE legend

stops flashing and play continues at the start

of the next track.

Press AUTOSPACE again to cancel this

mode.

DISPLAY

The CD Pre’s display can be switched off

with the DISPLAY button on the remote

control when a disc is playing.

However, if the button is pressed without a

CD being loaded, or with a disc stopped,

track, index and time displays are briefly

replaced by the word DISPLAY OFF to con

firm this mode has been engaged, but the

display remains lit until play is selected.

Pushing the button a second time briefly

shows DISPLAY ON to confirm that the

function has been cancelled.

When in display-off mode, pressing any but

ton will cause the display to return briefly to

confirm the new status before again switch-

ing off.

CD Pre Instructions for Use. Page 15 of 19

Issue 1: January 2002

CD TEXT

CD TEXT DISCS

A small number of CDs released for sale

more recently have additional text informa-

tion contained in the recorded digital data.

The CD Pre can individually display either

the disc title, artist’s name or track title with

appropriate control commands.

Only CDs which are identified as having

this text feature, either on the

disc’s label or the library case,

will have text function on the

CD Pre.

When a text disc is first loaded, a red

CD TEXT legend appears in the display

window.

Text is shown on the front display as

follows:

When the disc is first loaded:

Initially (1a): Total tracks and total time

then, after a few seconds, (1b):

Then, with each press of the TIME button,

the display will cycle between the two text

states:

2: Main artist’s name:

1: Return to 1a then 1b,

If a title or name has more than twelve char-

acters, the first 12 only will be diplayed

after the title or name has finished scrolling.

With disc playing:

Each press of the TIMEbutton, the display

will cycle between four states:

Original state:

1a: Track title

then, after a few seconds:

1b: Track elapsed time:

2: Track remaining time:

3: Disc remaining time:

4: Track title: (original play mode)

CD Pre Instructions for Use. Page 16 of 19

Issue 1: January 2002

CD Pre Instructions for Use. Page 17 of 19

Issue 1: January 2002

CD TEXT - OTHER LANGUAGES

Other Languages:

A limited number of CD text discs also

have an “other-language” option.

In this case, after loading the disc, the dis-

play shows the current or default language

after MULTI has been appeared underneath

the TEXT legend.

If the player cannot read one of the lan-

guages identified in the disc’s digital data,

the display will show “(OTHER LANG)”

after loading the text CD.

To change language with a suitable text

disc, before playing the text CD:

Press the LANGUAGE button on the front

panel. The current operating language will

then appear in the display.

Press NEXT or PREVIOUS on the front

panel, or |<< or >>| on the remote con-

trol to find the required language.

Press the LANGUAGE button again to

store the setting.

Notes:

* If a non-text disc is loaded, pressing the

LANGUAGE button has no effect.

* If a text disc which does not have other

languages available is loaded but not play-

ing, when the LANGUAGE button is

pressed “CAN’T SELECT” is displayed

* If the LANGUAGE button is pressed

while playing a multi-language text disc,

the current language is displayed momen-

tarily.

CD Pre Instructions for Use. Page 18 of 19

Issue 1: January 2002

TROUBLESHOOTING

Basic problem-solving with a pre-amplifier is similar to troubleshooting other electrical or elec-

tronic equipment. Always check the most obvious possible causes first, such as the following

examples:

Problem Possible Cause Remedy

No power when POWER Power plug is not inserted Plug in securely.

button is pressed fully into rear socket

No sound TAPE MONITOR button has Press TAPE MONITOR

been pressed button again to cancel.

MUTE button has been Press MUTE button again

pressed to cancel.

Wrong input selected Select correct input.

Sound is severely distorted, and Line output lead is connected Re-connect lead to auxilliary

the volume control needs to be to phono pickup input sockets sockets or other “line level”

turned down very low of the amplifier amplifier input.

No playback when CD is load- Disc has been loaded with Re-load with label side up.

ed, and “NO DISC” displayed the label side down

Mistracking (sound jumping) Player receiving vibration Change position of player

or shock away from speakers.

Disc is dirty Clean disc surface

Remote control does not work POWER switch is off Set switch to on.

One or more batteries inserted Insert batteries correctly.

the wrong way round

Batteries are flat Change batteries - do not

mix old and new ones.

Remote control is not pointed Ensure there is no obstruc-

directly towards the front tion between the remote

panel of the pre-amplifier control and front panel.

Remote control range has Batteries are running out Change batteries - do not

greatly reduced mix old and new ones.

If none of the above actions effect a cure, please contact your dealer or Musical Fidelity service

agent. Do not open the case of the CD Pre yourself, as this will invalidate the guarantee.

CD Pre Instructions for Use. Page 19 of 19

Issue 1: January 2002

CD Pre

Combination CD player / digital & analogue pre-amplifier

CD SECTION:

DAC architecture 24 bit Delta-Sigma (Bitstream)

8 times oversampling

(CD or DVD-audio conversion only)

Frequency response 20Hz to 20kHz: < 0.02dB

Channel balance 20Hz to 20kHz: < 0.02dB

Stereo separation 20Hz to 20kHz: > 98dB

Total harmonic 0dB digital level: 0.002%

distortion at 1kHz: -10dB digital level: 0.004%

-70dB digital level: 0.050%

Signal / noise ratio 20Hz to 20kHz: 110dB unweighted, 114dB A-weighted

Audio output at digital 0dB level, 1kHz: 2.14VRMS nominal, 47 ohms

Jitter: 189pS

PRE-AMPLIFIER SECTION:

Direct Analogue A to D / D to A *

Maximum output for 2.2 Volts RMS input: 8.4VRMS 8.2VRMS

Distortion 20Hz to 20kHz: < 0.002% < 0.004%

Frequency response 20Hz to 20kHz: + 0, - 0.02dB + 0, - 0.37dB

Crosstalk, typical: 85dB 90dB

Channel balance: 20Hz to 20kHz: < 0.01dB < 0.02dB

Signal / noise ratio, unweighted 20Hz to 20kHz: 106dB 101dB

A - weighted 20Hz to 20kHz: 109dB 104dB

* These measurements made by linking the co-axial digital output back to the digital monitor, and using

DIGITAL MONITOR function. This is converting an analogue signal to digital and then back to analogue,

as when linking to a computer or CD recorder.

Power requirements 100 / 115 / 230V AC 50 / 60Hz (Voltage factory preset for country)

Power consumption 22 Watts

Dimensions (approx.): 440mm wide Weight: 13.5Kg unit only, unboxed

140mm high (including feet) 17Kg in shipping carton

380mm deep (including terminals)

Standard accessories: Remote control handset,

IEC mains lead,

4 batteries (type SUM-4, AAA, LR03)

Musical Fidelity reserves the right to make improvements which may result in specification or feature changes without notice.

SPECIFICATIONS

Musical Fidelity CD Pre Specification

Brand: Musical Fidelity

Model: CD Pre

Type: Specification

This manual is also suitable for

Download PDF

report

Musical Fidelity CD Pre Specification

This manual is also suitable for

Musical Fidelity CD Pre Specification

Related papers

Other documents