Page is loading ...
OMRON CX-Supervisor – User Manual
Revision 2.0 Page i
Notice
OMRON products are manufactured for use according to proper procedures by a qualified operator
and only for the purposes described in this manual.
The following conventions are used to indicate and classify precautions in this manual. Always heed
the information provided in them. Failure to heed precautions can result in injury to people or
damage to the product.
DANGER! Indicates information that, if not heeded, is likely to result in loss of life or
serious injury.
WARNING Indicates information that, if not heeded, could possibly result in loss of
life or serious injury.
Caution Indicates information that, if not heeded, could result in relatively serious
or minor injury, damage to the product, or faulty operation.
OMRON Product References
All OMRON products are capitalised in this manual. The word “Unit” is also capitalised when it
refers to an OMRON product, regardless of whether or not it appears in the proper name of the
product.
The abbreviation “PLC” means Programmable Logic Controller and is not used as an abbreviation
for anything else.
OMRON CX-Supervisor – User Manual
Revision 2.0 Page iii
Visual Aids
The following headings appear in the left column of the manual to help you locate different types of
information.
Note: Indicates information of particular interest for efficient and convenient
operation of the product.
1, 2, 3… Indicates lists of one sort or another, such as procedures, checklists etc.
Represents a shortcut on the Toolbar to one of the options available on the
menu of the same window.
Indicates a program must be started, usually by clicking the appropriate
option under the standard Windows ‘Start’ button.
OMRON, 2007
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or
otherwise, without the prior written permission of OMRON.
All copyright and trademarks acknowledged.
No patent liability is assumed with respect to the use of the information contained herein. Moreover,
because OMRON is constantly striving to improve its high-quality products, the information
contained in this manual is subject to change without notice. Every precaution has been taken in the
preparation of this manual. Nevertheless, OMRON assumes no responsibility for errors or omissions.
Neither is any liability assumed for damages resulting from the use of the information contained in
this publication.
OMRON CX-Supervisor – User Manual
Revision 2.0 Page v
About this Manual
This manual describes the CX-Supervisor application and its ability to create, modify and run
SCADA applications.
This manual contains the following:
Chapter 1 - Graphics Editor. This chapter describes the Graphics Editor and its various tools and
controls.
Chapter 2 - Pages. This chapter describes the procedures involved in the creation and amendment of
pages.
Chapter 3 - Points. This chapter describes the procedures involved in the creation, amendment and
removal of points. The use of PLCs with points is also described.
Chapter 4 - Objects. This chapter describes procedures involved in the creation, amendment and
removal of objects.
Chapter 5 - ActiveX Objects. This chapter provides an overview of using ActiveX objects in CX-
Supervisor.
Chapter 6 - Projects. This chapter describes procedures involved in the creation, amendment and
removal of projects.
Chapter 7 - Graphics Library. This chapter describes the library of graphic objects and how to
create and amend new libraries.
Chapter 8 - Alarms. This chapter describes the procedures involved in the creation and amendment
of alarms.
Chapter 9 - Animation. This chapter describes the use of animations and how they can be applied to
a CX-Supervisor project.
Chapter 10 - Recipes. This chapter describes the creation of recipes, and how they can be used.
Chapter 11 - Data Logging. This chapter describes the data logging facilities, including setting up,
viewing and exporting
Chapter 12 - Databases. This chapter describes the Database facilities, including connections reading
and writing data.
Chapter 13 - Multilingual Features. This chapter describes the Multilingual features, including
creation of dynamically switching applications.
Chapter 14 - OPC Client. This chapter introduces OPC Server to a new user, and explains how to use
CX-Supervisor as an OPC Client
CX-Supervisor – User Manual OMRON
Page vi Revision 2.0
Chapter 15 - Connecting to a Remote CX-Supervisor application. This chapter explains how to
create a distributed solution by connecting together CX-Supervisor applications on networked
PCs.
Chapter 16 - Connecting to Omron Industrial Components. This chapter details connecting CX-
Supervisor to Omron's Industrial Components.
Chapter 17 – Best Practices. This chapter details the best practices to get the most from CX-
Supervisor including how to plan and design your application.
Appendix A – Configuring a PC for remote connection. The appendix explains how to configure a
PC for remote connection.
Appendix B – Frequently asked questions. The appendix list some FAQs, and of course their
answers.
Appendix C – Troubleshooting. The appendix is a guide to troubleshooting and resolving problems.
Appendix D – CX-Server error codes. The appendix lists the error codes from the communication
software, CX-Server, and their meanings.
Appendix E – Using with the Omron DyaloX. The appendix lists information when using with the
Omron’s DyaloX Industrial PC.
Appendix F – Obsolete Features. The appendix details obsolete features for backwards
compatibility only.
A Glossary of Terms and Index are also provided.
OMRON CX-Supervisor – User Manual
Revision 2.0 Page vii
TABLE OF CONTENTS
CX-Supervisor ..................................................................................................Page
Chapter 1 - Graphics Editor.......................................................... 1
About the Graphics Editor ...................................................................................... 1
Palette .................................................................................................................... 1
Graphic Object Bar................................................................................................. 4
Control Bar ............................................................................................................. 4
Status Bar............................................................................................................... 8
Text Bar .................................................................................................................. 9
Grid....................................................................................................................... 11
Chapter 2 - Pages.......................................................................... 13
Creating a Page.................................................................................................... 13
Amending a Page................................................................................................. 14
Defining the Properties of a Page ........................................................................ 14
Printing a Page ..................................................................................................... 16
Saving a Page to a Project................................................................................... 20
CX-Supervisor Preferences.................................................................................. 20
Chapter 3 - Points......................................................................... 23
What is a Point? ................................................................................................... 23
About the Point Editor .......................................................................................... 23
Viewing Points via the Point Editor....................................................................... 24
Creating a Point.................................................................................................... 27
Amending an Existing Point ................................................................................. 33
Deleting an Existing Point .................................................................................... 34
Quick creation of many points .............................................................................. 35
OMRON CX-Supervisor – User Manual
Revision 2.0 Page ix
Table of Contents chapter 3 continued Page
Runtime Point Maintenance ................................................................................. 36
Point Import ......................................................................................................... 37
System Points....................................................................................................... 38
Printing Points ...................................................................................................... 41
Chapter 4 - Objects ...................................................................... 45
Objects ................................................................................................................. 45
Editing Objects ..................................................................................................... 45
Creating and Editing Graphic Objects.................................................................. 44
Creating and Editing Control Objects................................................................... 48
Manipulating Objects............................................................................................ 63
Chapter 5 – ActiveX Objects ....................................................... 69
Overview............................................................................................................... 69
Inserting a new object .......................................................................................... 69
Editing Properties at Design Time........................................................................ 70
Reading and Writing Properties at Run Time....................................................... 72
Calling Methods at Run Time............................................................................... 72
Responding to Events .......................................................................................... 72
Chapter 6 - Projects...................................................................... 75
Overview............................................................................................................... 75
Creating a Project................................................................................................. 75
Amending a Project .............................................................................................. 76
Saving a Project ................................................................................................... 76
Printing a Project .................................................................................................. 77
Device Configuration ............................................................................................ 77
Settings................................................................................................................. 83
Runtime Settings .................................................................................................. 84
Runtime Security .................................................................................................. 91
OMRON CX-Supervisor – User Manual
Revision 2.0 Page xi
Table of Contents chapter 6 continued Page
Exit Level .............................................................................................................. 97
Compiling and Running a Project......................................................................... 95
Save Runtime As.................................................................................................. 98
Create Runtime Install Disc.................................................................................. 98
Project Information ............................................................................................... 99
Alias Definitions .................................................................................................... 99
Find..................................................................................................................... 100
Navigating Projects with the Workspace............................................................ 101
Project Editor ...................................................................................................... 101
Printing from the Project Editor .......................................................................... 104
Chapter 7 - Graphics Library ................................................... 105
Overview............................................................................................................. 105
Graphics Library ................................................................................................. 105
Manipulating Objects.......................................................................................... 107
Printing the Graphics Library.............................................................................. 109
Chapter 8 - Alarms..................................................................... 111
What is an Alarm? .............................................................................................. 111
Alarm Settings .................................................................................................... 111
Viewing the Contents of the Alarm Database .................................................... 113
Creating a New Alarm ........................................................................................ 114
Updating an Existing Alarm ................................................................................ 118
Copying an Existing Alarm Definition ................................................................. 119
Deleting an Existing Alarm ................................................................................. 119
Printing Alarms ................................................................................................... 119
Alarm Reporting In Runtime ............................................................................... 120
OMRON CX-Supervisor – User Manual
Revision 2.0 Page xiii
Table of Contents chapter 8 continued Page
Chapter 9 - Animation ............................................................... 123
Associating Points with Actions and Events....................................................... 123
Animation Editor ................................................................................................. 123
Runtime Actions ................................................................................................. 129
Chapter 10 - Recipes .................................................................. 157
What is a Recipe? .............................................................................................. 157
Recipe Components ........................................................................................... 157
Viewing Recipes in the Recipe Editor ................................................................ 158
Creating a New Recipe ...................................................................................... 160
OMRON CX-Supervisor – User Manual
Revision 2.0 Page xv
Table of Contents chapter 10 continued Page
Updating an Existing Recipe .............................................................................. 162
Copying an Existing Recipe Definition ............................................................... 164
Deleting an Existing Recipe ............................................................................... 164
Recipe Security Levels....................................................................................... 164
Printing Recipes ................................................................................................. 165
Using Recipes in Runtime .................................................................................. 166
Chapter 11 - Data Logging ........................................................ 171
What is Data Logging? ....................................................................................... 171
Data Log Editor................................................................................................... 171
Data Logging at Runtime................................................................................... 176
Data Log View Component ................................................................................ 180
Remote Data Log Viewer ................................................................................... 181
Data Log Export Facilities .................................................................................. 182
Data Logging ...................................................................................................... 184
Chapter 12 - Databases .............................................................. 189
Overview............................................................................................................. 189
Database Connection Editor .............................................................................. 189
Configuring a connection.................................................................................... 190
Configuring Recordsets...................................................................................... 197
Configuring Field Associations ........................................................................... 199
Configuring Parameter Associations .................................................................. 201
Configuring Schemas ......................................................................................... 202
Using Transactions............................................................................................. 206
Saving Recordsets as XML ................................................................................ 207
Datashaping ....................................................................................................... 207
OMRON CX-Supervisor – User Manual
Revision 2.0 Page xvii
Table of Contents Page
Chapter 13 – Multilingual features........................................... 213
Development Features ....................................................................................... 213
Runtime Language Features.............................................................................. 214
Runtime Mulitlingual Features............................................................................ 215
Configuring Windows for Language Support ..................................................... 218
Data Log Viewer ................................................................................................. 222
Adding Unsupported Runtime Languages ......................................................... 222
Popup Keyboard Layout..................................................................................... 223
Chapter 14 – Using CX-Supervisor as an OPC Client ........... 225
An Overview of OPC? ........................................................................................ 225
Using CX-Supervisor with OPC Servers ............................................................ 230
Using with Omron’s CX-Server OPC ................................................................. 235
Chapter 15 – Connecting to Remote Applications .................. 237
Two Tier, Client-Server or Master-Slave?.......................................................... 237
Peer to Peer ....................................................................................................... 238
Distributed Server............................................................................................... 238
Redundant Server .............................................................................................. 239
Creating a CX-Supervisor Server application .................................................... 239
Creating a CX-Supervisor Client application...................................................... 239
Chapter 16 – Connecting to Omron Industrial Components. 243
Adding a Point linked to a parameter ................................................................. 243
Chapter 17 – Best Practices....................................................... 249
Design ................................................................................................................ 249
Performance ....................................................................................................... 250
Points.................................................................................................................. 253
Drawing .............................................................................................................. 254
Scripts................................................................................................................. 255
Data Logging ...................................................................................................... 256
/