Atdec AWM-FF Installation guide

Atdec
Brand
Atdec
Model
AWM-FF
Type
Installation guide

Below you will find brief information for F Clamp AWM-FF. This document provides step-by-step instructions on how to install the F Clamp, which is compatible with Atdec AWM Series products. The guide emphasizes the importance of correct installation and surface suitability, which must support the weight of mounted equipment. The manual also specifies that this product is not suitable for surfaces with a bullnose or bevelled edge. The guide covers attaching the clamp to a post or base, adjusting for different work surface thicknesses, and finally fixing the clamp securely to the work surface.

Below you will find brief information for F Clamp AWM-FF. This document provides step-by-step instructions on how to install the F Clamp, which is compatible with Atdec AWM Series products. The guide emphasizes the importance of correct installation and surface suitability, which must support the weight of mounted equipment. The manual also specifies that this product is not suitable for surfaces with a bullnose or bevelled edge. The guide covers attaching the clamp to a post or base, adjusting for different work surface thicknesses, and finally fixing the clamp securely to the work surface.

AWM-FF Page 1 of 2
Installation Guide
AWM-FF
F Clamp
COMPONENT CHECKLIST
D
5mm
Hex Key
(x1)
A
Upper Clamp
(x1)
B
Lower Clamp
(x1)
C
Screw
M8 x 16mm
(x2)
REQUIRED TOOLS
• All tools provided
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with Atdec AWM Series products.
! The manufacturer accepts no responsibility for incorrect installation.
! Product must only be installed on a work surface capable of supporting the weight of all equipment being mounted.
! Product is not suitable for installation on work surfaces with a bullnose or bevelled edge.
AWM-FF Page 2 of 2
1. Attach post or base to upper clamp
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©202300929
Fasteners
supplied
with post
Fasteners
supplied
with base
1.1 Option A - Attach post to upper clamp 1.2 Option B - Attach base to upper clamp
Note: post sold separately Note: base sold separately
2. Attach lower clamp to upper clamp
2.1 Measure the worksurface thickness and
choose the suitable lower clamp position
2.3 Attach lower clamp to upper
clamp in the suitable position
using the two provided screws.
(Normal position shown here)
2.2 If using inverted
position change the
screw direction of
the lower clamp
A B
A B
A B
A - Normal
0 - 36mm
(0.00 - 1 ”)
B - Inverted
36 - 79mm
(1 ” - 3”)Note: If there is only a small gap
behind the worksurface, perform
Step 3.1 before this step.
3. Fit fixing to work surface
3.1 Place in desired location on worksurface
Post Installation
3.2 Screw in pressure plate and tighten firmly.
5mm
Hex Key
Mounting
surface
  • Page 1 1
  • Page 2 2

Atdec AWM-FF Installation guide

Atdec
Brand
Atdec
Model
AWM-FF
Type
Installation guide

Below you will find brief information for F Clamp AWM-FF. This document provides step-by-step instructions on how to install the F Clamp, which is compatible with Atdec AWM Series products. The guide emphasizes the importance of correct installation and surface suitability, which must support the weight of mounted equipment. The manual also specifies that this product is not suitable for surfaces with a bullnose or bevelled edge. The guide covers attaching the clamp to a post or base, adjusting for different work surface thicknesses, and finally fixing the clamp securely to the work surface.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents