Page is loading ...
– INSTRUCTION MANUAL –
DESIGN BY STEFAN DIEZ
TABLE GROUP 1
1A, 2A
NEW ORDER
TABLES
TABLE OVERVIEW
PARTS OVERVIEW
TABLE ASSEMBLY INSTRUCTIONS
CONNECTORS
TABLE WALL CONNECTOR INSTRUCTIONS
FRONT SHELF CONNECTOR INSTRUCTIONS
END SHELF CONNECTOR INSTRUCTIONS
END TRAY CONNECTOR INSTRUCTIONS
CABLE MANAGEMENT
CABLE TRAY INSTRUCTIONS
CABLE CLIP INSTRUCTIONS
CABLE GUIDE INSTRUCTIONS
WALL MOUNTING GUIDELINE
CARE AND MAINTENANCE
4
5
613
1417
1821
2225
2628
2931
3233
3435
36
37
TABLE OF CONTENTS
4
TABLE OVERVIEW
It is important to start by identifying your table model to ensure you follow
the correct assembly instructions.
TABLE
1A
TABLE
2A
100x50 100x100
PARTS
5
PARTS
TABLE
PART
x4
x4
x4
x1
x1 x1
x1 x1
x1 x1
A Corner knot *
B Frame profile
C Leg *
D Tabletop
x4
x4
x4
x1
4 Frame
5 Tabletop
6 Legs
BAG
4
BAG
5
BAG
6
TABLE
1A
TABLE
2A
* Quantity of corner knots and legs depends on your table configuration.
6
ESB
(EXTRA SUPPORT BAR)
The tables in this manual use extra support bars (ESB) to reinforce their construction.
You will find information below on how to mount them and find their correct position.
The small dotted markings on the table frame should align with the marks
indicated on the support bar connector.
The markings on the table frame are not numbered, but counting outwards
from the central mark (0) will guide you to the correct position for your
support bar.
INFORMATION ON SUPPORT BARS
0 1 45 6123 2 3456
7
INFORMATION ON SUPPORT BARS
6 5 4 3 2 1 0 1 2 3 4 5 6
0 1 45 6123 2 3456
TABLE
POSITION
FRAME PROFILE 150 CM
TABLE
7A
TABLE
9A
0
0
0
11 22 3
1
1
3
1
1
44
TABLE
6A
TABLE
10A
TABLE
5A
TABLE
4A
TABLE
8A
TABLE
11A
FRAME PROFILE 100 CM
FRAME PROFILE 75 CM
FRAME PROFILE 50 CM
TABLE
TABLE
TABLE
POSITION
POSITION
POSITION
011
011
SUPPORT BAR POSITIONS
0
22
3 3 44 1
1
8
1.
Insert the corner knots
A
into the two shortest table frame profiles
B
. Then connect
these with the two longest profiles to close the frame.
9
2.
Secure the frame with screws
4B
using tool
4A
in each corner.
M5x8 T15
4B
x32
T15
4A
x1
BAG
4
10
3.
Connect the legs
C
by threading it onto the tap of the corner knot.
Secure with screws
6B
using tool
6A
.
6B
x4
6A
x1
BAG
6
11
4.
Mount the tabletop
D
by inserting it into one of the short ends. While applying
upwards pressure in the middle, push the other short end down into place.
12
5.
Fasten the tabletop
D
with the clips
5B
from underneath. Distribute the clips evenly.
Secure them with screws
5C
using tool
5A .
5C
x10
5A
x1
5B
x10
BAG
5
13
6.
If the floor is uneven and the table is unstable, adjust the height of the feet until the
table is stable.
14
TABLE WALL CONNECTOR
B
Wall connector x2
C
Screw x4
A
Connector x2
PARTS
INSTRUCTION MANUAL
15
1.
Start by inserting the wall connectors
A
into the frame profile that is facing the wall.
16
Low table
737 mm
High table
1097 mm
2.
Mark the placement for the wall connector
B
according to the height measurements
below. Check that the holes are level and the connectors are fastened in a suitable and
secure way before you start drilling (See page 43).
17
3.
Mount the table from the top. Make sure that the connectors
A
are parallel to the wall
connectors
B . Screw the bracket into place using the 4 screws
C and torx key.
Finally mount the tabletop as described in the table instructions (page 13).
18
A Shelf connector x2
B Screw x4
PARTS
FRONT SHELF CONNECTOR
INSTRUCTION MANUAL
19
1.
Mount the shelf connnectors
A
onto the groove on the bottom of the shelf.
20
2.
Connect the table from the front. Then connect the shelf connector
A
by angling
it so that the profile locks into the groove at the bottom of the table frame, as
illustrated below.
WHEN MOUNTING
You may need to apply some extra
pressure to lock the connector in place.
/
