Page is loading ...
– INSTRUCTION MANUAL –
DESIGN BY STEFAN DIEZ
NEW ORDER
TABLE GROUP 7
7T, 7U, 7V
TABLES
TABLE OVERVIEW
PARTS OVERVIEW
TABLE ASSEMBLY INSTRUCTIONS
CONNECTORS
TABLE WALL CONNECTOR INSTRUCTIONS
FRONT SHELF CONNECTOR INSTRUCTIONS
END SHELF CONNECTOR INSTRUCTIONS
END TRAY CONNECTOR INSTRUCTIONS
CABLE MANAGEMENT
CABLE TRAY INSTRUCTIONS
CABLE CLIP INSTRUCTIONS
CABLE GUIDE INSTRUCTIONS
PLUG SOCKET
WALL MOUNTING GUIDELINE
CARE & MAINTENANCE
TABLE OF CONTENTS
5
67
822
2326
2730
3134
3537
3840
4142
4344
4548
49
50
4
5
150x150
150x150
150x150
TABLE
7T
TABLE
7U
TABLE
7V
It is important to start by identifying your table model to ensure you follow
the correct assembly instructions.
TABLE OVERVIEW
6
TABLE
7T
TABLE
7U
TABLE
7V
TABLE
PART
—
x3
x3
x3
x1
x1
x1
x2
x2
x2
x2
x2
x2
x2
x2
x4
x4
x4
x4
x4
x4 x4
x4
x4
x4
x4
x4
A Corner knot*
B Frame profile
C Leg**
D Tabletop
E Support bar
F Extra support bar
I Screen
G Tray
H Single profile
*Quantity of corner knots and legs depends on your table configuration.
**Only for high tables with footrest.
PARTS
7
—
x1
x1
x1
x2
x2
J Screen mount
K Screen mount
——
—
—
x2
x2
x2
x2
x2
L Cable management
2 Extra supportbar
BAG BAG BAG BAG BAG
3 Supportbar
4 Frame
5 Tabletop
6 Legs
12 Screen
3
4
5
6
12
PARTS
BAG
2
x2
x2
x2
x1
x1
x1
x4
x4
x4
x1
x1
x1
x3
x3
x3
11 Tray divider
BAG
11
8
SB
(SUPPORT BAR)
ESB
(EXTRA SUPPORT BAR)
New Order tables uses two support bars to reinforce the construction.
The two different types are 'Support bar' (SB) and 'Extra support bar' (ESB)
The small dotted markings on the table frame should align with the marking
on the support bar/extra support bar connector.
The markings on the table frame are not numbered, but counting from the
center mark (0) will guide you to the correct position for your support bar.
INFORMATION ON SUPPORT BARS
0 1 45 6123 2 3456
SB
SB
ESB
ESB
9
INFORMATION ON SUPPORT BARS SUPPORT BAR POSITIONS
6 5 4 3 2 1 0 1 2 3 4 5 6
0 1 45 6123 2 3456
TABLE
POSITION
FRAME PROFILE 150 CM
TABLE
7T
TABLE
7U
TABLE
7V
10
FIND THE CORRECT
POSITION IN THE
OVERVIEW ON PAGE 8
3A
x2
x4 x2
BAG
3
1.
Insert the brackets
3A
into the two shortest table frame profiles
B .
Then mount the
ESB connectors
2D and the SB connectors found in support bar
E on both frame
profiles
and fasten them with screws
3C using tool
3B
. Make sure to find the
correct position on page 8, before tigthening screws completely.
BAG
2
3B
x1
3C
x4
2D
x2
FIND THE CORRECT
POSITION IN THE
OVERVIEW ON PAGE 8
8
8
Connector is
delivered with
the support
bar
E .
11
2.
Insert the corner knots
A
into the two table frame profiles from step 1.
Then connect them with the other two profiles
B
to close the frame.
Place the support bars
E and extra support bars
F in between.
12
3.
Secure the frame with screws
4B
using tool
4A
in each corner.
4B
x32
4A
x1
BAG
4
13
3C
x4
3B
x1
BAG
3
4.
Fasten the support bar
E and extra support bar
F
with screws
3A using tool
3B
.
14
6B
x4
6A
x1
BAG
6
5.
Connect the legs
C
by threading them onto the tap of the corner knot.
Secure with screws
6B
using tool
6A
.
15
Mount the profile connectors
11A with screws
11B using tool
? in the
table top
D with holes in the corners.
6.
11B
x4
11A
x4
BAG
11
16
Mount screen holder
L .
Secure with screws
12A with screen
I
. .
Placement of screens depends on your table model.
BAG
12
12A
x4
Screen holders are
delivered inside
the screens.
SEE WHERE TO PLACE
SCREENS IN TABLE
OVERVIEW ON PAGE 4
4
7.
ONLY FOR TABLES 7U, 7V
17
8.
Place the tabletops
D
. Start with the outer two and then the middle one.
Then place the cable covers
M
in between the tabletops.
18
5C
x10
5A
x1
5B
x10
BAG
5
9.
Fasten the tabletop
D
with the clips
5B
from underneath. Distrubute the clips evenly.
Secure them with screws
5C using tool
5A .
19
10.
Place profiles
H on the fittings on the middle tabletop.
Then mount the tray
G
on
top of the profiles.
20
11.
Secure the profiles by tightening the set screws, both in top and bottom, on all profiles.
/
