Classic Exhibits VK-1224 Setup Instructions

Brand: Classic Exhibits

Model: VK-1224

Type: Setup Instructions

Classic Exhibits VK-1224 is a versatile and customizable display system designed to meet the needs of various exhibition and event requirements. Its modular construction allows for easy assembly and reconfiguration, making it suitable for both large-scale events and smaller, targeted displays.

The VK-1224 features a sturdy aluminum frame that ensures durability and stability. The included lighting system provides optimal illumination for showcasing products or graphics, while the spacious shelves offer ample room for product display or literature distribution.

Order #XXXXX

Locked layer contains

placeholder marks.

Plan View 10’

10’

VK-1224 - 10’ x 10’ Display

REV 11/2022

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX

Locked layer contains

placeholder marks.

= 1 sq foot

Plan View

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Order #XXXXX

Locked layer contains

placeholder marks.

1) Mounting plate & wing nuts,

in packed position.

6) Place fixed counter bolts

into mounting plate, then

secure using wing nuts.

Completed Assembly

Counter Attachment

Wing Nut

Fixed

Bolts

Mounting

Plate [11A]

Counter

Attach mounting plate to curved extrusion

[10], using bolt. Insert fixed bolts, located

on underside of counter, into holes of flange

plate. Secure with wing nuts.

Mounting Plate

w/ Wing Nuts

Bottom view

of counter

Wing Nut

Counter

2) Mounting plate bolt in,

packed position.

Bolt

5) Tighten bolt, using hex tool,

to secure.

Mounting Plate

Bolt

3) Place mounting plate onto

[10] then tighten bolt, part

way, allowing some rotation

for final positioning.

4) Place fixed counter bolts

into mounting plate, then lift

counter to re-tighten bolt.

Mounting Plate

Fixed

Counter

Bolt

Fixed

Counter

Bolt

Hex Tool

Keep mounting plate [11A] and wing nuts

attached to counter, when packing.

Keep bolt attached to [10], when packing.

Bolt

Mounting

Plate

Bottom view of counter Bottom view of counter

Counter Assembly

Case 1 of 1

Order #XXXXX

Locked layer contains

placeholder marks.

Top View of Each Level

A,A

B,B

3A,3B

2B,2A

4A, 4B, 5A, 5B

Level 2 Level 3Level 1 (Bottom Level)

Wing Panels

Round

Sign

Assembled

Header

Shelf

Graphics

Lights

Setup Hardware

Monitor Mount

Base

Plates

10A 11

11A

Counter

Top

Level 4

Base

Plates

10A 11

11A

Counter

Top

Case Packing

Step 1 of 2

Order #XXXXX

Locked layer contains

placeholder marks.

Connection Bar

Bolt

5A A

Velcro on extrusions

must face to BACK of

assembled Backwall.

Velcro on

BACK/Bottom Edges

of Top Horizontals

Velcro on BACK/Top

Edges of Bottom

Horizontals

Velcro on BACK/Inside

Edges of Right Verticals

Velcro on BACK/Inside

Edges of Left Verticals

Horizontal Placement

Stopper

Set upper horizontal extrusion

on top of stopper of verticals.

FRONT VIEW

When Assembled

Steps:

1) Attach base plates [1] lower verticals [2A] and [3A], using bolts.

2) Connect verticals [2A to 2B] and [3A to 3B], using connection bars [B].

See Straight Connection with Knobs detail.

3) Connect horizontals [4A to 4B] and [5A to 5B], using connection bars [A].

See Straight Connection with Knobs detail.

4) Connect assemblies [2A/2B] and [3A/3B] with assemblies [4A/4B] and [5A/5B].

See Corner Connection with Knob detail.

5) Connect extrusions [6A to 2B] and [6B to 3B].

See 2.5”h Angle-Cut Vertical Attachment detail.

6) Attach graphic to Velcro on back of assembled Backwall.

Set Screw

Connector

2.5”h Angle-Cut

Vertical Attachment

Back View of Backwall

Insert connector into groove

of vertical extrusion, then

tighten set screw to secure.

Velcro

Slide connection bar between

extrusions, then turn knobs

clockwise to tighten lock.

Straight Connection

with Knobs

Do not over tighten Knobs

Knob

Corner Connection

with Knob

Turn knob clockwise

to tighten lock.

Do not over tighten Knobs

Knob Keep extrusions [6A,6B]

attached to [2B,3B].

Keep A10 clamps

attached to [2A,2B,3A,3B].

Item

2A,2B

3A,3B

4A,4B

5A,5B

6A,6B

Description

Base Plate

42” S40 Vertical Extrusion w/ A10 Clamps

45” Z45 Horizontal Extrusion

2.5” S40 Angle-Cut Vertical

Qty.

1,1

Connection bars [A]

stay attached to [4A,5A].

Connection bars [B]

stay attached to [2A,3A].

Backwall Assembly

Step 2 of 2

Order #XXXXX

Locked layer contains

placeholder marks.

Connector

Sign Attachment

Cap

Sign

Standoff

Slide connector into groove of extrusion.

Tighten set screws to secure in place.

Screw standoff into connector. Place

sign between standoff and cap then

tighten cap to secure sign.

Slide light onto clip then lock clip

into groove of horizontal extrusion.

Clip

Light

Light Connection

Clip

Light

Horizontal Extrusion

Wing

Clamp

Wing

Knob

Set Screw

Connector

1) Slide connector of clamp

into extrusion groove.

2) Tighten set screw when

A10 is in desired location.

3) Insert wing into clamp.

4) Tighten knob on clamp

to secure wing in place.

Clamp Attachment

A10 Clamp

Keep A10 clamps

attached to verticals.

Keep curved extrusion [10]

& horizontal [11] assembled.

FRONT VIEW

Monitor Mount Attachment

Connectors

Slide V4 Connectors into groove

of Extrusion. Tighten Set Screws

to secure connectors in place.

Attach Monitor Mount back

piece to Extrusion, using bolts.

Then slide monitor mount into

back piece.

Bolts

Monitor

Mount

Back

Piece

Steps:

1) Connect lights to top horizontal extrusions [5A/5B]. See Light Connection detail.

2) Attach assembled Header Frame and affix graphic using Velcro.

3) Attach extrusions [10/11] and shelf to verticals [2A] & [3A].

4) Attach support legs [10A] to curved extrusions [10].

5) Attach flange plates [11A] to top of curved extrusions [10], using bolts.

6) Attach counter tops to counter mounting plates [11A]. See Counter Assembly page.

7) Attach Wings to A10 clamps. See Clamp Attachment detail.

8) Attach Monitor Mount to vertical [2B]. See Monitor Mount Attachment detail.

9) Attach Sign to vertical extrusion [3B]. See Sign Attachment detail.

Item

7/8/9

10A

11A

Qty.

1/1/1

Description

Header Frame

30.2” Curved Extrusion

Support Leg

12.184” Horizontal Extrusion

Counter Mounting Plate

Keep header

frame assembled,

when packing.

Velcro on extrusions

must face to BACK of

assembled Header.

Graphic

11A

10A

Screw

Shelf

11A

10A

Screw

When assembled

Backwall Attachments

Classic Exhibits VK-1224 Setup Instructions

Classic Exhibits VK-1224 Setup Instructions

Classic Exhibits VK-1224 Setup Instructions

Related papers

Other documents