Eizo CG3145 User manual

Important

Please read this “User’s Manual” carefully to familiarize yourself

with safe and eective usage.

• For the latest product information including the “User’s Manual”,

refer to our web site:

www.eizoglobal.com

Color Management Software

User’s Manual

Version 7.1

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by

any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.

EIZO Corporation is under no obligation to hold any submitted material or information condential unless

prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although

every eort has been made to ensure that this manual provides up-to-date information, please note that

specications are subject to change without notice.

2

CONTENTS

CONTENTS ............................................................. 3

Chapter 1 Introduction ....................................... 5

1-1. About ColorNavigator 7 ............................... 5

1-2. Features ......................................................... 5

1-3. Requirements for ColorNavigator 7 ............ 6

●Computer ......................................................... 6

●Monitor ............................................................ 6

●Measurement Device ...................................... 7

1-4. Model Limitations ......................................... 8

Chapter 2 Setup .................................................. 9

2-1. Installing the Software ................................. 9

●Mac .................................................................. 9

●Windows .........................................................10

●Linux ...............................................................10

2-2. Connecting the USB Cable .........................11

2-3. If the Monitor is not Detected .....................12

2-4. Warming up the Monitor .............................13

2-5. Uninstalling the Software ...........................14

●Mac .................................................................14

●Windows .........................................................14

●Linux ...............................................................14

Chapter 3 Basic Usage..................................... 15

3-1. Before You Use .............................................15

3-2. How to Open the Main Window ..................15

●Mac .................................................................16

●Windows .........................................................18

●Linux .............................................................. 20

3-3. Main Window Structure ...............................21

●Color mode type is Advanced (ADV) .............21

●Color mode type is Standard (STD) or

Sync Signal (SYNC) ...................................... 22

3-4. Calibrating the Monitor .............................. 25

●Verifying the Calibration Result......................31

3-5. Manual Adjustment ..................................... 33

●Color mode type is Advanced (ADV) ............ 33

●Color mode type is Standard (STD) or

Sync Signal (SYNC) ...................................... 38

3-6. Creating a New Target ................................ 40

3-7. Editing Target Values ................................. 42

3-8. Selecting Targets for Color Mode ..............47

3-9. Calibrating the Monitor Periodically ......... 48

3-10. Validating the Monitor's Adjustment

Status ........................................................... 50

3-11. Management of Color Mode....................... 52

●Changing the Color Mode Type .................... 53

●Renaming the Color Mode ............................ 53

●Setting the Color Mode to Enable/Disable .... 54

●Resetting the Color Mode to Default ............. 54

3-12. Target Management .................................... 55

●Adding a Target ............................................. 56

●Deleting Targets ............................................ 56

●Exporting Targets .......................................... 57

●Importing Targets .......................................... 57

Chapter 4 Advanced Usage ............................. 58

4-1. Correlation between the Built-in Sensor

and the Measurement Device .................... 58

4-2. Locking the Control Buttons of the

Monitor ......................................................... 59

4-3. Registering Asset Information to the

Monitor ......................................................... 60

4-4. Adjusting the Light Booth .......................... 60

4-5. Measuring Display Devices ........................61

●Displaying the Measurement Result

Management Window ................................... 62

●New Measurement ........................................ 63

●Editing Measurement Result ..........................67

●Sharing Measurement Result ........................67

4-6.

Creating an ICC Prole Display Devices ...

68

4-7. Emulation ......................................................70

●Using the ICC prole / Measurement result ...70

●LogView LUT Emulation ................................. 71

4-8. Monitor Option Settings ............................. 72

4-9. Exporting and Importing Monitor

Settings ........................................................ 72

●Exporting Monitor Settings ........................... 72

●Importing Monitor Settings .............................73

Chapter 5 Preferences ..................................... 74

5-1. How to Compensate Measurement

Values ............................................................75

5-2. ColorNavigator Agent Settings ..................76

5-3. ICC Prole Detail Settings ......................... 77

5-4. Checking the Resolution at Startup ......... 78

5-5. Do Not Apply an ICC Prole ....................... 79

5-6. Participating in the Quality Improvement

Program........................................................ 79

5-7. Language Settings ...................................... 79

●Setting the Display Language ....................... 79

●Adding a Display Language .......................... 80

5-8. Managing Validation Targets ..................... 80

●Adding a Validation Target ............................ 80

●Deleting a Validation Target .......................... 82

●File Formats of Validation Targets ................ 82

5-9. ColorNavigator Network Connection ....... 84

3

CONTENTS

Chapter 6 Other Functions .............................. 85

6-1. Displaying Test Patterns ............................ 85

6-2. Displaying the version information. ......... 86

6-3. Checking for Software Updates ................ 87

6-4. Checking the License Information ............ 87

6-5. Displaying the System Information .......... 88

Chapter 7 Troubleshooting .............................. 89

Chapter 8 Error Messages ............................... 90

List of Functions ................................................. 96

Appendix .............................................................. 97

Trademark ................................................................97

License .....................................................................97

4CONTENTS

5

Chapter 1 Introduction

1-1. About ColorNavigator 7

ColorNavigator 7 is the dedicated software for EIZO's “ColorEdge” color management monitors that

feature an excellent color display.

Using ColorEdge together with ColorNavigator 7 allows you to calibrate your monitor, create and edit

targets, and manage multiple monitors easily yet accurately.

1-2. Features

• The software links up to the monitor's color modes to let you congure the targets for each of them.

After calibrating the monitor with ColorNavigator 7, you can easily switch display states by changing the color

mode using the control buttons on the monitor.

Color Modes in ColorNavigator 7

Monitor

OSD

Linking

• A variety of targets are available for your applications, including photography, design, printing, web

content and video creation, and more.

• Color mode types that best suit your needs are selectable.

ColorNavigator 7 oers the following color mode types: “Advanced (ADV)”, “Standard (STD)”, and “Sync Signal

(SYNC)”.

Depending on the color mode type you choose, calibration levels and content that you can manually adjust will be

dierent.

ColorNavigator 7 allows you to select color mode types that can optimize your display to best suit your purpose.

See “3-11. Management of Color Mode” (page 52) for details.

• Periodic calibration can be scheduled.

For monitors with a built-in sensor, calibration is automatically performed at the congured intervals.

(SelfCalibration/SelfCorrection)

6Chapter 1 Introduction

1-3. Requirements for ColorNavigator 7

●Computer

Common

• Resolution: recommended resolution of the monitor*1

• USB port: at least two free ports required (at least one free port for monitors with a built-in

calibration sensor)*2

*1 For details on the recommended monitor resolution, see the User's Manual of your monitor.

*2 An EIZO USB cable is required to connect the monitor to the computer.

Mac

• OS:

-macOS Ventura (13)

-macOS Monterey (12)

-macOS Big Sur (11)

-macOS Catalina (10.15)

• Mac that satises the OS requirements

• Colors: 16.7 million or more colors

Windows

• OS:

- Windows 11 (64-bit editions)

- Windows 10 (64-bit editions)

• Memory: the same requirement for your OS

• Colors: 24-bit or more

Attention

• Not compatible with Windows on ARM.

Linux

• OS:

- Red Hat Enterprise Linux 7 (64-bit editions)

- Red Hat Enterprise Linux 8 (64-bit editions)

●Monitor

• EIZO ColorEdge PROMINENCE series monitor

• EIZO ColorEdge CG series monitor with a built-in calibration sensor

• EIZO ColorEdge CS/CX series monitor

For more information, refer to our web site (www.eizoglobal.com).

7

Chapter 1 Introduction

●Measurement Device

Attention

• This product does not come with a measurement device. Please purchase a measurement device separately

at a dealer as needed.

• For details of the system requirements and usage of measurement devices, see the User’s Manual of each

product.

• Do not connect and use multiple measurement devices that are the same model.

• For CG3145 / CG3146, the following measurement devices are not supported:

- X-Rite i1Display 3, i1Display Pro, i1Display Pro Plus, i1Studio

-Calibrite ColorChecker Display Pro, Display Plus, Studio

-EIZO EX3, EX4

-Datacolor Spyder5, SpyderX, SpyderX2

- Konica Minolta CA-310, CA-310M, MYIRO-1

-DK-Technologies PM5639/94

Measurement device Type Win Mac Linux

Built-in calibration sensor of the monitor *1 Filter P P P

Built-in correction sensor of the monitor *2 Filter P P P

X-Rite i1Pro 2 / i1Pro 3 Spectral P P -

X-Rite i1Studio

Calibrite ColorChecker Studio

Spectral P P -

X-Rite i1Display 3 / i1Display Pro / i1Display Pro Plus *3

Calibrite ColorChecker Display Pro / Display Plus *4

Filter P P P

Datacolor Spyder5 / EIZO EX3

Datacolor SpyderX / EIZO EX4

Datacolor SpyderX2

Filter P P -

Konica Minolta CA-310 / CA-310M / CA-410 *5 Filter P- -

Konica Minolta CS-2000 / CS-2000A *5 Spectral

Konica Minolta CS-200 *5 Spectral tting

Konica Minolta MYIRO-1 Spectral P P -

Klein K-10 / K-10A *6 Filter P P P

Photo Research PR-655 / PR-680 *6 Spectral P P P

Colorimetry Research CR-100 *6 Filter P P P

Colorimetry Research CR-250 / CR-300 *6 Spectral

JETI Specbos 1211 *6 Spectral P- -

JETI Spectraval 1501 / 1511 *6

TOPCON SR-UL1R Spectral P- -

DK Technologies PM-5639 / 94 Filter P- -

*1 CG2420's and CG2730's built-in calibration sensors do not support monitor validation.

*2 Only SelfCorrection is supported.

*3 i1 Display Studio cannot be used.

*4 ColorChecker Display cannot be used.

*5 The driver is not provided. Please contact the manufacturer.

*6 It will be displayed in the list when you uncheck “Display only automatically detected device” on the

measurement device selection window.

8Chapter 1 Introduction

1-4. Model Limitations

Some functions are limited for the models listed below.

Applicable Models

CS230

Limitations

• The color mode type cannot be changed. For more information about the color mode types, see

“3-11. Management of Color Mode” (page 52).

- “CAL” mode: Fixed to Advanced (ADV)

- Other than “CAL” mode: Fixed to Standard (STD)

• When the color mode is other than “Custom” / “User 1” / “User 2” / “User 3”, manual adjustment is

not available.

9

Chapter 2 Setup

2-1. Installing the Software

Attention

• Be sure to shut down all the running applications before executing the installation.

• ColorNavigator 7 cannot be installed with ColorNavigator 6 or ColorNavigator NX in the same environment.

Please choose one of these to use.

• When ColorNavigator 7 is installed in the environment where ColorNavigator 6 or ColorNavigator NX is installed,

the existing software will be uninstalled.

• When you upgrade from ColorNavigator 6, the targets used in ColorNavigator 6 will be carried over to

ColorNavigator 7.

Reference

• ColorNavigator 7 is available for download from our web site (www.eizoglobal.com).

●Mac

1. Double-click the downloaded “ColorNavigator7xx.pkg” le.

The installer starts up.

2.

Install the software.

Follow the instructions to install the software.

Attention

• A message indicating “Requesting access to control System Events” will appear depending on the

environment. Since it is required for enabling the resident function (ColorNavigator Agent) of ColorNavigator 7,

click “OK”.

10 Chapter 2 Setup

●Windows

Attention

• A user account with “Administrator” privileges is required.

• Please consult your system administrator for the privilege setting of your account.

1. Double-click the downloaded “CN7xx_Setup.exe” le.

The installer starts up.

2.

Install the software.

Follow the instructions to install the software.

Attention

• The “Windows Security” dialog box may appear several times when you install the software. If this dialog box

is displayed, select “Install” and proceed with the installation until the dialog box is no longer displayed.

●Linux

Note

• Contact your local EIZO representative about downloading the Linux version of the installer.

1. After unzipping the downloaded le, run “install.sh”.

The installer starts up.

2.

Install the software.

Follow the instructions to install the software.

Attention

• A user account with root privileges is required.

• The ColorNavigator 7 icon in the task tray may not appear when starting up after the initial installation. In that

case, log in to the computer again.

• The following restrictions apply if you are using Red Hat Enterprise Linux 8.

-When opening the main window, you must manually select the monitor on which the main window will be

displayed.

-When system information is displayed, “Monitor name” and “S/N” of the display information are not

displayed.

- The ICC prole is not created even if the color mode is switched while ColorNavigator is running as a

resident program.

11

Chapter 2 Setup

2-2. Connecting the USB Cable

1. Use the provided USB cable (MD-C93 or UU200SS) to connect the USB Type-B

connector (upstream) of the monitor to the USB Type-A connector (downstream)

of the computer.

Attention

• If your computer does not have a Type-A connector but has a ThunderboltTM 3 or USB Type-C connector, add

a commercially available USB Type-C to Type-A conversion adapter.

• Under default setting, Connector 1 is enabled when a monitor with two USB Type-B connectors (upstream) is

used. Connect the USB cable to the connector indicated as “1”.

• Do not remove the USB cable while ColorNavigator 7 is operating. Doing so may result in system freeze or

software malfunction.

Note

• If you use a USB Type-C cable to connect your monitor with the computer, this step is not necessary.

2.

If you use an external measurement device, make sure that the measurement

device is connected to the USB Type-A connector (downstream) of your

computer or monitor.

Attention

• Depending on the measurement device, limitations may apply to the connected USB port. For more

information about connecting measurement devices, refer to the user’s manual of the measurement device.

• Do not remove the measurement device from the USB port while ColorNavigator 7 is operating. Doing so may

result in system freeze or software malfunction.

Note

• If you use the built-in calibration sensor, there is no need to connect an external measurement device.

• By installing ColorNavigator 7, the drivers for the corresponding measurement devices are also installed at

the same time. There is no need to install the driver provided with the measurement device (for Windows

only).

12 Chapter 2 Setup

2-3. If the Monitor is not Detected

If the monitor is not detected, the following messages will be displayed when ColorNavigator 7 starts up.

If the monitor is not detected, check the following.

• Check that the monitor and the computer are correctly connected with a USB cable. (Refer to “2-2.

Connecting the USB Cable” (page 11).)

• If your computer has more than one USB Type-A connector (downstream), try connecting it to

another connector.

• Check that your environment meets the operating conditions of ColorNavigator 7. (Refer to “1-3.

Requirements for ColorNavigator 7” (page 6).)

• If you are using a ColorEdge-series monitor that does not meet the operating conditions of

ColorNavigator 7, use a previous version of ColorNavigator.

• Turn o the computer and turn it back on.

13

Chapter 2 Setup

2-4. Warming up the Monitor

The monitor cannot display images accurately right after the monitor is turned on because the brightness

and chromaticity are not stabilized. Before performing adjustments, turn on the power of the monitor and

warm it up.

Attention

• The warming-up time varies depending on the monitor being used. For details on the warming-up time, see the

User's Manual of the monitor.

• SelfCorrection requires a warming-up that takes 60 minutes or more.

1. Turn on both the monitor and the computer.

2.

Disable the power management function of the computer.

Disable the power management function of the computer so that it does not enter the power-saving

mode while warming up.

Attention

• When the computer enters the power-saving mode, the monitor enters in the state where the power is turned

o. Therefore, it takes some time for the brightness and chromaticity to re-stabilize once the computer comes

out of the power-saving mode.

3.

Set the display resolution and number of colors.

The monitor should be used at the recommended resolution.

Set the monitor color to 16.7 million (24-bit) or more.

Note

• For details on the recommended monitor resolution, see the User's Manual of your monitor.

14 Chapter 2 Setup

2-5. Uninstalling the Software

●Mac

1. Open the computer’s library folder.

Note

• The library folder can be opened with the following procedure.

1. Click the “Finder” icon on the Dock while pressing “control”, or right-click the icon and select “Go to the

folder:” from the menu.

2. Enter “/Library”, and click “Move”.

2.

Select the “EIZO” folder from the “Application Support” folder.

The “EIZO” folder opens.

3.

Select the “tools” folder from the “ColorNavigator 7” folder.

The “tools” folder opens.

4.

Double-click the “ColorNavigator 7 Uninstaller.app” le.

Note

• To delete all the data including adjustment data from the computer, go to the “tools” folder and double-click

“ColorNavigator 7 Uninstaller Full.app”.

• When you enter the following in the “Go to the folder:”, you can directly open the folder where the uninstaller

is stored. /Library/Application Support/EIZO/ColorNavigator 7/tools

●Windows

Attention

• A user account with “Administrator” privileges is required.

• Please consult your system administrator for the privilege setting of your account.

1. Click “Start” - “Settings” - “Apps”.

2.

Click “Uninstall” for “ColorNavigator 7” from the list.

●Linux

Note

• Contact your local EIZO representative about downloading the Linux version of the installer.

1. After unzipping the downloaded le, run “uninstall.sh”.

The installer starts up.

2.

Uninstall the software.

Follow the instructions to uninstall the software.

Attention

• A user account with root privileges is required.

15

Chapter 3 Basic Usage

3-1. Before You Use

You need to select a color mode type that is appropriate for your applications and color management

policies. See “3-11. Management of Color Mode” (page 52) for details.

One target and setting is assigned to each color mode.

If you have a specic target you want to use, you need to assign this target to any of the color modes that

are set to Advanced (ADV) See “3-8. Selecting Targets for Color Mode” (page 47) for details.

The color mode can be switched in the following methods:

• Switching from the color mode list of the ColorNavigator 7 main window.

• Switching from the menu of the ColorNavigator Agent.

Note

• The settings made in ColorNavigator 7 will be saved in the monitor unit itself.

3-2. How to Open the Main Window

Attention

• When multiple monitors are connected, each monitor should display an independent screen. Displaying the same

screen on each monitor or across multiple monitors prevents adjustment using the ColorNavigator 7 software.

ABAA

A

Independent screen on each

monitor (Supported)

Same screen on each monitor

(Not supported)

A screen over the multiple

monitors (Not supported)

• When you use ColorNavigator 7 for the monitor with a laptop computer connected, you have to disable the

mirroring/duplicating display settings in the OS settings. Adjustment using ColorNavigator 7 is not possible if

identical screens are displayed on the monitor and laptop computer.

ABAA

Independent screen on the monitor and laptop PC

monitor (Supported)

Same screen on the monitor and laptop PC

monitor (Not supported)

(Mirroring/duplicating)

16 Chapter 3 Basic Usage

●Mac

The main window can be opened with any of the following methods.

●Double-click the “ColorNavigator 7” icon inside the “Application” folder.

●Click the LaunchPad icon on the Dock. Enter “ColorNavigator 7” in the search area,

and click the “ColorNavigator 7” icon displayed in the search results.

●Click the search icon on the menu bar to open the Spotlight search window. Enter

“ColorNavigator 7” and then click the “ColorNavigator 7” icon displayed in the search

results.

The ColorNavigator icon appears on the menu bar, and the main window opens.

17

Chapter 3 Basic Usage

Note

• If a message “The adjustment capable monitor cannot be found.” is displayed, refer to “2-3. If the Monitor is not

Detected” (page 12).

• If a message “Screen error” is displayed, refer to “9. Screen Error” (page 90).

If the Main Window Does not Open

1. Click the ColorNavigator icon on the menu bar to open the menu.

2.

Select “Start ColorNavigator”.

18 Chapter 3 Basic Usage

●Windows

The main window can be opened with any of the following methods.

●Click “Start” - “All apps” - “EIZO” - “ColorNavigator 7”.

●Double-click the “ColorNavigator 7” icon on the desktop.

Large icon Medium icon Small icon

19

Chapter 3 Basic Usage

●After selecting “apps” in Windows le search, enter “ColorNavigator 7” and click the

“ColorNavigator 7” icon displayed in the search results.

The ColorNavigator icon appears on the task tray, and the main window opens.

Note

• If a message “The adjustment capable monitor cannot be found.” is displayed, refer to “2-3. If the Monitor is not

Detected” (page 12).

• If a message “Screen error” is displayed, refer to “9. Screen Error” (page 90).

20 Chapter 3 Basic Usage

If the Main Window Does not Open

1. Right-click the ColorNavigator icon on the task tray to open the menu.

2.

Select “Start ColorNavigator”.

●Linux

Open the main window with the following method.

●Go to the “Application” menu and select “Accessories” - “ColorNavigator 7”.

Page is loading ...

Eizo CG3145 User manual

Eizo CG3145 User manual

Related papers

Other documents