Planex MZK-NAS01SG User manual

Multi Media Network Attached

Storage 1 Bay / Storage 2 Bay

MZK-NAS01SG / MZK-NAS02SG

Foreword

Explanation of the signals

In order to let you set up and use this product correctly, please pay attention when reading or

browsing the manual as you see these signals listed below.

Warning/ Danger

Users should read the explanation carefully and understand it completely, otherwise

users might be in danger or even be injured.

Caution/ Be Careful

Remind users to be careful when setting up the product and to avoid damaging the

product or its system programs.

Seeking for service or searching for an agent or a distributor

Thank you for purchasing products from Planex Communications Inc. If you have any

operational problems while conﬁguring or setting up the product, you may contact with our

Customer Service Department or ask the agent or the distributor from which you bought

the product for help. Moreover, during warranty, if you ﬁnd any defect or breakdown of the

product, you may bring the product, assembly, and its warranty card to our company or to

where you bought the product to ask for repair.

★Every product has different warranty period and contract; please refer to our

company for further information or consult the agent or the distributor.

Planex Communications Inc.

Support Phone：+65-6338-1704 (Singapore)

+886-2-7705-6172/6173/6174 (Taiwan)

Customer Service E-Mail：[email protected]

Contact Us

Tel：+886-2-7705-6689

Fax：+886-2-7705-6688

Agents & Distributors：http://www.planex.net/where/index.htm

Trademarks:

To maintain compliance with FCC RF exposure compliance requirements, please avoid direct

contact to the transmitting antenna during transmitting.

Contents

Foreword

Chapter1

Introduction of MZK-NAS01SG/MZK-NAS02SG

. .1

1. Contents of Package . . . . . . . . . . . . . . . . . . .2

Chapter 2 Function Introduction and Quick Install Guide

. .3

1. Product Functions . . . . . . . . . . . . . . . . . . . . . .3

2. Installation Guide . . . . . . . . . . . . . . . . . . . . . .7

Chapter 3 Web Configuration and RAID . . . . . . . . . . . . . 17

1. WEB Configuration . . . . . . . . . . . . . . . . . . . . 17

2. Building RAID (For MZK-NAS02SG Only) . . . .19

Chapter 4 Common Functions . . . . . . . . . . . . . . . . . . . .23

1. Adding Users . . . . . . . . . . . . . . . . . . . . . . . . .23

2. Adding Groups . . . . . . . . . . . . . . . . . . . . . . . 25

3. File Server . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4. BT Download . . . . . . . . . . . . . . . . . . . . . . . . .33

5. WEB/FTP Download. . . . . . . . . . . . . . . . . . . .37

Chapter 5 Detail Function . . . . . . . . . . . . . . . . . . . . . . . .41

1. Language . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

2. Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

MZK-NAS01SG/MZK-NAS02SG

3. Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

3.1. Time Zone . . . . . . . . . . . . . . . . . . . . . . . .43

3.2. Password. . . . . . . . . . . . . . . . . . . . . . . . . 44

4. Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

5. File/FTP Server . . . . . . . . . . . . . . . . . . . . . . . .46

5.1. Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

5.2. Groups . . . . . . . . . . . . . . . . . . . . . . . . . . 48

5.3. File Server . . . . . . . . . . . . . . . . . . . . . . . . 50

5.4. FTP Server . . . . . . . . . . . . . . . . . . . . . . . . 55

6. BitTorrent . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

7. Web/FTP Download . . . . . . . . . . . . . . . . . . .64

8. iTunes Server . . . . . . . . . . . . . . . . . . . . . . . . .66

9. Media Server . . . . . . . . . . . . . . . . . . . . . . . . .69

10. Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

10.1. Storage Tools (For MZK-NAS02SG) . . . . 71

10.2. Storage Status . . . . . . . . . . . . . . . . . . . 73

10.3. USB Copy . . . . . . . . . . . . . . . . . . . . . . . 73

10.4. Configuration Tools . . . . . . . . . . . . . . . 74

10.5. Firmware Update . . . . . . . . . . . . . . . . . 76

10.6. Reset . . . . . . . . . . . . . . . . . . . . . . . . . . .78

MZK-NAS01SG/MZK-NAS02SG Contents

MZK-NAS01SG/MZK-NAS02SG

1

Introduction to MZK-NAS01SG /

MZK-NAS02SG

Thank you for purchasing MZK-NAS01SG/MZK-NAS02SG Network

Attached Storage (NAS) server. This Storage device can let you share your

files with users all around your network easily. All you have to do is insert

your SATA hard disks into MZK-NAS01SG/MZK-NAS02SG, connect the

LAN port with a LAN cable (RJ45 connectors), some basic settings, and

you’re ready to share your files on your LAN network. MZK-NAS01SG/

MZK-NAS02SG provide the perfect file sharing/storage solution for

medium size business or Small Office/Home Office (SOHO).

MZK-NAS01SG/MZK-NAS02SG have a built-in Web server, thus you can

access its settings through Web browsers, such as IE, Netscape, Firefox,

and so on. You can set up and configure the settings easily and completely

and enjoy the convenience instantly.

MZK-NAS01SG/MZK-NAS02SG have many features, which includes:

● Support two internal SATA hard disk drives (MZK-NAS02SG only)

● Provide two USB ports for USB mass storage devices connecting

● Sharing your files via FTP or Network Neighborhood

● Sharing your multimedia files to DLNA compliant media adapters, such

as Xbox 360 and Sony PS3

● Built-in iTunes Server allows you to share your music with all the users

on your local Network.

● Download functions allow you to download files through FTP, World

Wide Web (WWW), and BitTorrent.

● High file transfer rate (more than 100Mbps)

1

Chapter1 Introduction to MZK-NAS01SG/MZK-NAS02SG

1

2

MZK-NAS01SG/MZK-NAS02SG

1. Contents of Package

After purchasing MZK-NAS01SG/MZK-NAS02SG Network Attached

Storage (NAS) server form a distributor or an agency, please open the

package and check that all the components listed below are included. If

there is any item missing or damaged, please contact with the distributor or

the agency at once.

MZK-NAS01SG

● MZK-NAS01SG

● CD-ROM (User’s Manual)

● AC Adapter

● AC Power Cable

● Screw (x4)

● Rubber Foot (x4)　

● UTP cable

● Warranty Card

MZK-NAS02SG

● MZK-NAS02SG

● CD-ROM (User’s Manual)

● AC Adapter

● AC Power Cable

● Screw (x8)

● Rubber Foot (x4)　

● UTP cable

● Warranty Card

If plug the AC adapter which includes in the product package

into a socket with different voltage power supply, it will cause

damage and that is not included in warranty.

2

3

Chapter2 Function Introduction and Quick Install Guide

2

Function Introduction and Quick

Install Guide

Front Panel

LED Status Meaning

Power On/Flashing

After turning MZK-NAS01SG/MZK-NAS02SG, the

Power LED will be on. If MZK-NAS01SG/MZK-

NAS02SG is shutting down or restoring to the default

settings, the Power LED will be ﬂashing.

LAN 1/2 On/Off

LAN LED will be on when the LAN port is

connected, and will be off when the LAN port is

disconnected.

USB 1 / 2 On/Flashing

When connecting with a USB storage device (with

FAT32, FAT16, and EXT2 format), the LED will be on.

The LED will be flashing when copying files

from the USB device to MZK-NAS01SG/MZK-

NAS02SG.

HDD 1/2 On/Flashing

When internal SATA hard disk is connected and

formatted by MZK-NAS01SG/MZK-NAS02SG, the

HDD LED will be on accordingly.

● LEDs and Meanings:

1. Product Functions

MZK-NAS01SG MZK-NAS02SG

2

4

MZK-NAS01SG/MZK-NAS02SG

●Release Button:

The Release button has three functions: 1. Unplug the external USB

mass storage connected to the USB 1 port. 2. Shut down MZK-

NAS01SG/MZK-NAS02SG. 3. Reset the configuration of MZK-

NAS01SG/MZK-NAS02SG to factory default settings (when pressing

Copy button at the same time).

◆Unplug the external USB storage device: Press and hold Release

button for 2 seconds, MZK-NAS01SG/MZK-NAS02SG will beep

for 0.5 second to hint that your command is detected. Release the

Release button immediately, and unplug the external USB storage

device plugged in USB1 port safely. If you want to unplug the external

USB device connected to the USB 2 port, please doing so by using

MZK-NAS01SG/MZK-NAS02SG configuration webpage. (Tools ->

Storage Status -> Unplug)

◆Shut down MZK-NAS01SG/MZK-NAS02SG: Press and hold

Release button for more than 5 seconds to start shutting down the

storage server. Ignore the first short beeping sound. The Power

LED will keep flashing, and you will hear a long beeping sound.

When the Power LED goes off, MZK-NAS01SG/MZK-NAS02SG

are completely shut down. You can now switch off the power by

switching the Power switch on the back panel of MZK-NAS01SG

/MZK-NAS02SG.

◆Restore the configuration of MZK-NAS01SG/MZK-NAS02SG to

factory default settings: If you want to reset the configurations of

MZK-NAS01SG/MZK-NAS02SG to factory default settings, you

should press and hold BOTH the Release button and the Copy buttons

at the same time for more than 5 seconds until you hear a long beep.

The Power LED will keep flashing during the restore process. After the

restore is complete, MZK-NAS02SG will restart automatically.

2

5

Chapter2 Function Introduction and Quick Install Guide

●Copy Button:

The Copy button has two functions: 1. Copy the content of one external

USB storage device to another attached storage device. 2. Reset the

configuration of MZK-NAS01SG/MZK-NAS02SG to factory default

settings (when pressing Release button at the same time).

◆Copy USB mass storage device: Press and hold the Copy button

for 2 seconds, MZK-NAS01SG/MZK-NAS02SG will beep for 0.5

second to hint that your command is detected. Release the Copy

button immediately if you want to copy the content of one external

USB mass storage device to another attached storage device. During

the process of copy, the LED of corresponding USB port will flash

slowly. When the LED of corresponding USB port stops flashing and

is lit steady, the copy job is finished. If any error occurs during the

process of copy, the LED of corresponding USB port will flash very

fast. The default source storage is USB 1. You can change the source

storage by USB Copy settings in MZK-NAS02SG’s Web user

interface.

◆Restore the configuration of MZK-NAS01SG/MZK-NAS02SG to

factory default settings: If you want to reset the configurations of

MZK-NAS01SG/MZK-NAS02SG to factory default settings, you

should press and hold BOTH the Release button and the Copy

buttons at the same time for more than 5 seconds until you hear a

long beep. The Power LED will keep flashing during the restore

process. After the restore is complete, MZK-NAS02SG will restart

automatically.

●USB 1: USB 1 port allows you to share your files stored in the USB

mass storage device plugged in.

2

6

MZK-NAS01SG/MZK-NAS02SG

Back Panel

Ports Function

USB 2

USB 2 port allows you to share your ﬁles stored in the USB mass

storage device plugged in. Also, USB 2 ports allows you to format

the attached USB storage device

LAN 1/2

Use standard LAN cables (RJ45 connectors) to connect MZK-

NAS01SG/MZK-NAS02SG with your hubs/switches, or one LAN

port of your router, etc.

DC

Plug the power cord into this port and the other side of the adaptor

should be plugged into the socket.

Button Function Usage

Power

On/Off

Turning On/

Off MZK-

NAS01SG/

MZK-

NAS02SG

Please do not turn off the power while MZK-

NAS01SG/MZK-NAS02SG is running. This will

cause data saving errors and MZK-NAS01SG/MZK-

NAS02SG may not be able to work properly. Before

switching off the power, please press Release button

for more than 5 seconds and shut down MZK-

NAS01SG/MZK-NAS02SG ﬁrst.

MZK-NAS01SG MZK-NAS02SG

2

7

Chapter2 Function Introduction and Quick Install Guide

2. Installation Guide

Please follow this step-by-step guide and install your MZK-NAS01SG/

MZK-NAS02SG.

1.Please push the button of the hard disk drawer in the back panel of

MZK-NAS01SG/MZK-NAS02SG, releasing the drawer lock.

2.Pull out the hard disk drawer gently.

2

8

MZK-NAS01SG/MZK-NAS02SG

3.Place your SATA hard disk on the hard disk drawer as shown in the

picture.

Note: When you put the SATA hard disk on the hard disk drawer,

make sure the screw holes of the hard disk match those of the

drawer.

4.Fix your SATA hard disk tightly in the hard disk drawer with the

screws provided in the MZK-NAS01SG/MZK-NAS02SG package.

2

9

Chapter2 Function Introduction and Quick Install Guide

5.After securing the SATA hard disk tightly to the hard disk drawer, slide

the drawer back to MZK-NAS01SG/MZK-NAS02SG gently as shown

in the picture.

6.Push the leverage of the hard disk drawer, sliding the drawer further

into MZK-NAS01SG/MZK-NAS02SG until you hear a slight “click

” sound.

Note: Please make sure the hard disk drawer is installed correctly as

shown in the picture.

2

10

MZK-NAS01SG/MZK-NAS02SG

7.Plug in the RJ45 cord to any LAN port on the back panel of

MZK-NAS01SG/MZK-NAS02SG.

8.Plug in the other side of the RJ45 cord to the LAN port of your PC or

router.

2

11

Chapter2 Function Introduction and Quick Install Guide

9.P l u g i n t h e p o w e r a d a p t e r p r o v i d e d i n M Z K- N A S01S G/

MZK-NAS02SG package into the DC port, and the other side in the

power socket as shown in the picture.

Plug the AC Adapter which comes with MZK-NAS01SG/MZK-

NAS02SG in a different voltage power supply will cause damage

on MZK-NAS01SG/MZK-NAS02SG, and it is not included in

warranty.

2

12

MZK-NAS01SG/MZK-NAS02SG

10. Turning on MZK-NAS01SG/MZK-NAS02SG by pressing the Power

On/OFF switch in the back panel.

11. If your computer is having trouble connecting to MZK-NAS01SG/

MZK-NAS02SG and the configuration webpage isn’t displayed

properly, please follow the steps down below and configurate your

computer.

●Click “Start” button (it should be located at lower-left corner of your

computer), and then click “Control Panel”.

Before turning your MZK-NAS01SG/MZK-NAS02SG on, make

sure that your MZK-NAS01SG/MZK-NAS02SG is connected to

the router properly. If you fail to do so, your computer may not be

able to connect to MZK-NAS01SG/MZK-NAS02SG.

2

13

Chapter2 Function Introduction and Quick Install Guide

●Double-click “Network and Internet Connections”, and then click

“Network Connections”.

Page is loading ...

Planex MZK-NAS01SG User manual

This manual is also suitable for

Planex MZK-NAS01SG User manual

Related papers

Other documents