Hitachi RB 14DL Technical Data And Service Manual

Category
Rechargeable batteries
Type
Technical Data And Service Manual

This manual is also suitable for

Hitachi RB 14DL is a lightweight and compact cordless blower equipped with a new lithium-ion battery that can be fully charged in just 45 minutes using the included charger. With a maximum air volume of 2.2 m3/min, it effectively clears dust and debris from various surfaces. Its ergonomic grip handle and low noise level ensure comfortable operation. Ideal for cleaning facilities, equipment, and devices in workshops or industrial settings.

Hitachi RB 14DL is a lightweight and compact cordless blower equipped with a new lithium-ion battery that can be fully charged in just 45 minutes using the included charger. With a maximum air volume of 2.2 m3/min, it effectively clears dust and debris from various surfaces. Its ergonomic grip handle and low noise level ensure comfortable operation. Ideal for cleaning facilities, equipment, and devices in workshops or industrial settings.

• Cleaning facilities and equipment in lumbermills, cigarette-making plants, spinning mills, etc.
• Cleaning devices and equipment in repair shops
• Blowing operation
PRODUCT NAME
Hitachi 14.4 V/18 V Cordless Blower
Models RB 14DL, RB 18DL
[ NEW FEATURES ]
Equipped with the new lithium-ion battery
Lightweight and compact
Maximum air volume 2.2 m
3
/min
Soft-grip handle
The new Models RB 14DL and RB 18DL are cordless blowers applicable to 14.4 V/18 V lithium-ion batteries.
(1) Applicable to the newly developed lithium-ion batteries (14.4 V/18 V 3.0 Ah, sold separately).
This battery can be fully charged in 45 minutes.
(2) Lightweight and compact
(3) Grip handle for easier handling
We aim to expand our market share with the new Models RB 14DL and RB 18DL.
LIST Nos.
RB 14DL: G870
RB 18DL: G871
Jun. 2007
MARKETING OBJECTIVE
APPLICATIONS
SELLING POINTS
International Sales Division
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.
R
RB 18DL
REMARK:
For more information about HANDLING INSTRUCTIONS, visit our website at:
http://www.hitachi-koki.com/manual_view_export/
Throughout this TECHNICAL DATA AND SERVICE MANUAL, a symbol(s) is(are) used in the
place of company name(s) and model name(s) of our competitor(s). The symbol(s) utilized here
is(are) as follows:
Competitors
Symbols Utilized
Company Name Model Name
C1 MAKITA UB141DZ
C2 MAKITA UB181DZ
CONTENTS
Page
SELLING POINT DESCRIPTIONS -----------------------------------------------------------------------------------------1
SPECIFICATIONS --------------------------------------------------------------------------------------------------------------2
1. Specifications -----------------------------------------------------------------------------------------------------2
COMPARISONS WITH SIMILAR PRODUCTS--------------------------------------------------------------------------3
1. Specification comparisons -------------------------------------------------------------------------------------3
PRECAUTIONS IN SALES PROMOTION--------------------------------------------------------------------------------4
1. Safety instructions -----------------------------------------------------------------------------------------------4
2. Inherent drawbacks of cordless blower requiring particular attention
during sales promotion -----------------------------------------------------------------------------------------5
REPAIR GUIDE------------------------------------------------------------------------------------------------------------------7
1. Precautions in disassembly and reassembly --------------------------------------------------------------7
2. Precautions in disassembly and reassembly of battery charger --------------------------------------8
STANDARD REPAIR TIME (UNIT) SCHEDULES----------------------------------------------------------------------9
Assembly diagram for RB 14DL
Assembly diagram for RB 18DL
-1-
Equipped with the new lithium-ion battery
The newly developed Types BCL 1430, EBL 1430 (for the Model RB 14DL), EBM 1830 (for the Model RB
18DL) lithium-ion batteries (14.4 V/18 V, 3.0 Ah) can be fully charged by the Model UC 18YRL charger in 45
minutes.
Lightweight and compact
The Models RB 14DL and RB 18DL are most compact and lightweight in the class.
Model RB 14DL: 1.5 kg
Model RB 18DL: 1.7 kg
Maximum air volume 2.2 m
3
/min
The fan shape and the air ducts are optimized to realize the greatest air volume 2.2 m
3
/min in the class.
Soft-grip handle
The grip is soft and slip-resistant for comfortable operation.
SELLING POINT DESCRIPTIONS
Battery (BCL 1430, EBL 1430)
(for the Model RB 14DL)
Battery (EBM 1830)
(for the Model RB 18DL)
Charger (UC 18YRL)
Charger voltage: 7.2 V to 18 V
-2-
1. Specifications
Model
RB 14DL RB 18DL
Type of motor
DC magnet motor
Type of switch
Trigger switch
No-load speed
15,000 min
-1
Enclosure
Main body: ABS resin (black)
Air pressure
3.9 kPa
Air volume
2.2 m
3
/min
Continuous operating time
15 min (battery 14.4 V 3.0Ah) 19 min (battery 18 V 3.0Ah)
Weight (with battery)
1.5 kg 1.7 kg
Standard accessory NN
Nozzle ----------------------- 1
Model
BCL 1430, EBL 1430 EBM 1830
Type of battery
Sealed cylindrical lithium-ion storage battery
Nominal voltage
DC 14.4 V DC 18 V
Nominal life
Charging/discharging: Approx. 1,500 times
Batteries
(sold
separately)
Nominal capacity
3.0 Ah
Charger (Model UC 18YRL)
(sold separately)
Overcharge protection system:
(1) Battery voltage detection (- V system)
Battery temperature detection (dT/dt system) for Ni-MH and
SUPER Ni-MH batteries
(2) Battery surface temperature detection (thermistor)
(3) 120-minute timer
(4) Stop current detection (Li-ion batteries)
Power input: 95 W
Charging time: Approx. 45 minutes [for battery at 20°C (68°F)]
Operable ambient temperature range: 0°C to 40°C (32°F to
104°F)
The maximum allowable temperature of the battery is 50°C
(122°F).
Indication method of battery charging function
NOTE: The Model UC 18YRL cools the overheated battery by the cooling fan during the
standby mode.
SPECIFICATIONS
-3-
(Superior specifications:
)
1. Specification comparisons
Maker HITACHI
Model name
(without battery/charger)
RB 14DL RB 18DL
C1 C2
Air pressure kPa 3.9 6.0
Air volume flow m
3
/min 2.2 0 to 2.2
Noise level
(with nozzle)
dB 84
-
Type of switch
-
Trigger switch Variable speed control trigger switch
Continuous
operating time
min
9.0
(Battery 14.4 V,
3.0 Ah)
11.0
(Battery 18 V,
3.0 Ah)
7.0
(Battery 14.4 V,
3.0 Ah)
9.5
(Battery 18 V,
3.0 Ah)
No-load speed min
-1
15,000 0 to 18,000
Overall length
(with nozzle)
mm
480 516 530
Weight
(with battery)
kg
1.5 1.7 1.9 2.1
Standard accessory Nozzle Nozzle
COMPARISONS WITH SIMILAR PRODUCTS
-4-
1. Safety instructions
In the interest of promoting the safest and most efficient use of the Models RB 14DL and RB 18DL cordless
blowers by all of our customers, it is very important that at the time of sale, the salesperson carefully
ensures that the buyer seriously recognizes the importance of the contents of the Handling Instructions,
and fully understands the meaning of the precautions listed on the caution plate and name plate attached to
each tool.
A. Handling instructions
Salespersons must be thoroughly familiar with the contents of the Handling Instructions in order to give
pertinent advice to the customer. In particular, they must have a thorough understanding of the precautions
for use of the cordless tools which are different from those of ordinary electric power tools.
(1) Before use, ensure that the unit is fully charged.
New units are not fully charged. Even if the units were fully charged at the factory, long periods of
inactivity, such as during shipping, cause the storage battery to lose its charge. Customers must be
instructed to fully charge the unit prior to use.
(2) When charging storage batteries, use only the exclusive Model UC 18YRL charger provided with
the tool.
Because of the designed rapid-charging feature (about 45 minutes), use of other battery chargers is
hazardous.
(3) Connect the charger to an AC power outlet only.
Use of any other power source (DC outlet, fuel powered generator, etc.) will cause the charger to
overheat and burn out.
(4) Do not use any voltage increasing equipment (transformer etc.) between the power source and
the charger.
If the charger is used with voltage higher than that indicated on the unit, it will not function properly.
(5) Conduct battery charging at an ambient temperature range of 10°C - 40°C (50°F - 104°F).
Special temperature sensitive devices are employed in the charger to permit rapid charging. Ensure
that customers are instructed to use the charger at the indicated ambient temperature range. At
temperature under 10°C (50°F) the thermostat will not function properly, and the storage battery may be
overcharged. At temperature over 40°C (104°F), the storage battery cannot be sufficiently charged. The
optimum temperature range is 20°C - 25°C (68°F - 77°F).
(6) The battery charger should not be used continuously.
At high ambient temperature, if over three storage batteries are charged in succession, the temperature
of the coils on the transformer will rise and there is a chance that the temperature fuse inserted in the
interior of the transformer will inadvertently melt. After charging one battery, please wait about 15
minutes before charging the next battery.
(7) Do not insert foreign objects into the air vents on the charger
The charger case is equipped with air vents to protect the internal electronic components from
overheating. Caution the customer not to allow foreign materials, such as metallic or flammable objects,
to be dropped or inserted into the air vents. This could cause electrical shock, fire, or other serious
hazards.
PRECAUTIONS IN SALES PROMOTION
-5-
(8) Do not attempt to disassemble the storage battery or the charger.
Special devices, such as a thermostat, are built into the storage battery and charger to permit rapid
charging. Incorrect parts replacement and/or wiring will cause malfunctions which could result in fire or
other hazards. Instruct the customer to bring these units to an authorized service center in the event
repair or replacement is necessary.
(9) Disposal of the storage battery (Types BCL 1430 and EBL 1430 for the Model RB 14DL, EBM 1830
for the Model RB 18DL)
Ensure that all customers understand that the storage batteries Types BCL 1430 and EBL 1430 for the
Model RB 14DL and EBM 1830 for the Model RB 18DL should be returned to the Hitachi power tool
sales outlet or the authorized service center when they are no longer capable of being recharged or
repaired. If thrown into a fire, the battery may explode.
B. Caution plate
The following cautions are listed on the name plate attached to each of the Types BCL 1430, EBL 1430 and
EBM 1830.
[ For Europe ]
[ For the U.S.A. and Canada ]
2. Inherent drawbacks of cordless blower requiring particular
attention during sales promotion
The cordless blower offers many advantages: it can be used in places where no power source is available,
the absence of a cord allows easy use, etc. However, any cordless tool has certain inherent drawbacks.
Salespersons must be thoroughly familiar with these drawbacks in order to properly advise the customer in
the most efficient use of the tool.
A. Suggestions and precautions for efficient use of the tool
(1) Use the cordless blower for comparatively light work.
Because the Models RB 14DL and RB 18DL are battery-operated, the output of the motor in cordless
blower is rather low in comparison with conventional electric power tools. Accordingly, they are not
suitable for continuous blowing in succession, which creates a heavy load. Salespersons should
recommend conventional electric power tools for such heavy work.
-6-
(2) Do not insert a foreign object into body.
A foreign object inserted through a hole may cause a failure. Please instruct customers to never insert a
foreign object into body.
(3) Avoid “Locking” of the motor.
Locking of the motor will cause an overload current that could result in burning of the motor and/or rapid
deterioration of the battery. Salespersons should advise the customer to immediately release the switch
and stop operation if the motor becomes locked.
(4) Variation in amount of work possible per charge
Although the nominal chargeable capacity of the storage batteries Types BCL 1430, EBL 1430 and
EBM 1830 is 3.0 Ah, the actual capacity may vary within 10% of that value depending on the ambient
temperature during use and charging, and the number of times the batteries have been recharged. It
should be noted that other factors which may have a bearing on the amount of work possible per charge
are the working conditions and the operational skill of the user.
B. Suggestions and precautions for efficient use of the charger and the storage battery
If the Types BCL 1430, EBL 1430 and EBM 1830 storage batteries are exposed to direct sunlight for an
extended period or if the tool has just been operated for a long time, charging may not be possible if the
temperature of the battery is above 40°C (104°F). In such a case, the customer should be advised to place
the battery in a shaded area with a good airflow, and allow sufficient cooling before recharging. This
phenomenon is common to all existing batteries and chargers which employ temperature sensitive
overcharge protection devices. The cooling time required before recharging can be accomplished varies
from a few minutes to about 45 minutes, depending on the load, duration of use, and ambient temperature.
-7-
Be sure to remove the storage battery from the main body before servicing. Inadvertent triggering of the
switch with the storage battery connected will result in danger of accidental turning of the motor.
1.Precautions in disassembly and reassembly
The [Bold] numbers in the description below correspond to the item numbers in the Parts List and the
exploded assembly diagram for the Models RB 14DL and RB 18DL.
1. Removal of the fan
Be sure to draw on work gloves before holding the Fan [15] to prevent injury to fingers. Remove the Nozzle
[22] from the main body. Remove the Tapping Screw D3.5 x 15 (Black) [18] and the Tapping Screw D3.5 x
20 [20] that secure Housing (L) [19] to the casing. Remove the Nut M6 [16] and pull out the Fan [15] from
the motor shaft.
2. Removal of the motor
After removal of the Fan [15], remove the Tapping Screw D3.5 x 15 [14] that secures the casing to Housing
(R) [9]. Remove the Machine Screw M4 x 10 [8] that secures the casing to the Motor [11], and remove the
Motor Plate [13]. Then the Motor [11] can be removed together with Motor Holder (A) [12]. In either case,
the Motor [11] can be removed by lightly tapping the end of Housing (R) [9] with a wooden hammer.
3. Disassembly of the power supply unit
Remove the Battery Holder [7] from Housing (R) [9]. The internal wires of the Micro Switch [2] and the
Motor [11] are soldered to the Battery Holder [7]. Unsolder and remove the internal wires.
REPAIR GUIDE
Disassembl
y
-8-
Reassembly can be accomplished by following the disassembly procedures in reverse. However, special
attention should be given to the following items.
1. Reassembly of the power supply unit
2. Reassembly of others
Reassembly can be accomplished by following the above disassembly procedure in reverse.
Machine Screw M4 x 10 [8]------------------------------------------------------------ 1.8 ± 0.4 N
m (18 ± 4 kgfcm)
Tapping Screw D3.5 x 15 [14]--------------------------------------------------------- 1.6 ± 0.3 N
m (16 ± 3 kgfcm)
Tapping Screw D3.5 x 15 (Black) [18]----------------------------------------------- 1.6 ± 0.3 N
m (16 ± 3 kgfcm)
Tapping Screw D3.5 x 20 (Black) [20]----------------------------------------------- 1.6 ± 0.3 N
m (16 ± 3 kgfcm)
Nut M6 [16] ------------------------------------------------------------------------------- 4.9 ± 1.0 N
m (50 ± 10 kgfcm)
2. Precautions in disassembly and reassembly of battery charger
Refer to the Technical Data and Service Manual for precautions in disassembly and reassembly of the
battery charger Model UC 18YRL.
Reassembl
y
Screw ti
g
htenin
g
torque
Perform wiring according to the wiring diagram.
Micro Switch [2]
Battery Holder [7]
Motor (W/Spindle) [11]
Motor Holder (B) [10]
Black
Red
Red
-9-
MODEL
Variable
Fixed
10 20 30 40 50 60
Work Flow
RB 14DL
RB 18DL
General Assembly
Housing (R)
Housing (L)
Micro Switch
Switch Knob
Motor Holder
(B)
Motor Holder
(A)
Motor
Motor Plate
Fan
STANDARD REPAIR TIME (UNIT) SCHEDULES
ELECTRIC TOOL PARTS LIST
LIST NO. G870
CORDLESS BLOWER
Model RB 14DL
2007
6
15
(E1)
Hitachi Power Tools
18
20
9
10
11
12
13
14
15
16
22
17
3
8
1
4
7
2
19
5
6
21
*
ALTERNATIVE PARTS
--- 2 --- 6 -- 07
RB 14DL
OPTIONAL ACCESSORIES
ITEM
NO.
CODE NO.
DESCRIPTION
REMARKS
NO.
USED
PARTS
ITEM
NO.
CODE NO.
DESCRIPTION REMARKS
NO.
USED
Printed in Japan
(070615N)
1 NAME PLATE 1
2 328-612 MICRO SWITCH 1
3 328-613 SWITCH SPRING (B) 1
4 328-654 SWITCH BAR 1
5 328-655 SWITCH SPRING (A) 1
6 328-614 SWITCH KNOB 1
7 328-611 BATTERY HOLDER 1
8 949-216 MACHINE SCREW M4X10 (10 PCS.) 2
9 328-610 HOUSING (R) 1
10 328-560 MOTOR HOLDER (B) 1
11 328-561 MOTOR (W/SPINDLE) 1
12 328-553 MOTOR HOLDER (A) 1
13 328-563 MOTOR PLATE 1
14 328-550 TAPPING SCREW D3.5X15 3
15 328-564 FAN 1
16 949-556 NUT M6 (10 PCS.) 1
17 328-565 STRAP 1
18 328-546 TAPPING SCREW D3.5X15 (BLACK) 8
19 328-609 HOUSING (L) 1
20 328-549 TAPPING SCREW D3.5X20 (BLACK) 1
21 HITACHI LABEL 1
22 328-562 NOZZLE 1
601 317-124 LONG NOZZLE ASS’Y 1
602 323-587 DUST BAG (DEEP BLUE) 1
603 990-046 NOZZLE (B) 1
ELECTRIC TOOL PARTS LIST
LIST NO. G871
CORDLESS BLOWER
Model RB 18DL
2007
6
15
(E1)
Hitachi Power Tools
18
21
9
10
11
12
13
14
15
16
22
17
8
1
2
5
6
3
4
7
20
19
*
ALTERNATIVE PARTS
--- 2 --- 6 -- 07
RB 18DL
OPTIONAL ACCESSORIES
ITEM
NO.
CODE NO.
DESCRIPTION
REMARKS
NO.
USED
PARTS
ITEM
NO.
CODE NO.
DESCRIPTION REMARKS
NO.
USED
1 NAME PLATE 1
2 328-612 MICRO SWITCH 1
3 328-613 SWITCH SPRING (B) 1
4 328-654 SWITCH BAR 1
5 328-655 SWITCH SPRING (A) 1
6 328-614 SWITCH KNOB 1
7 328-611 BATTERY HOLDER 1
8 949-216 MACHINE SCREW M4X10 (10 PCS.) 2
9 328-610 HOUSING (R) 1
10 328-560 MOTOR HOLDER (B) 1
11 328-615 MOTOR (W/SPINDLE) 1
12 328-553 MOTOR HOLDER (A) 1
13 328-563 MOTOR PLATE 1
14 328-550 TAPPING SCREW D3.5X15 3
15 328-564 FAN 1
16 949-556 NUT M6 (10 PCS.) 1
17 328-565 STRAP 1
18 328-546 TAPPING SCREW D3.5X15 (BLACK) 8
19 328-616 HOUSING (L) 1
20 328-549 TAPPING SCREW D3.5X20 (BLACK) 1
21 HITACHI LABEL 1
22 328-562 NOZZLE 1
Printed in Japan
(070615N)
601 317-124 LONG NOZZLE ASS’Y 1
602 323-587 DUST BAG (DEEP BLUE) 1
603 990-046 NOZZLE (B) 1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Hitachi RB 14DL Technical Data And Service Manual

Category
Rechargeable batteries
Type
Technical Data And Service Manual
This manual is also suitable for

Hitachi RB 14DL is a lightweight and compact cordless blower equipped with a new lithium-ion battery that can be fully charged in just 45 minutes using the included charger. With a maximum air volume of 2.2 m3/min, it effectively clears dust and debris from various surfaces. Its ergonomic grip handle and low noise level ensure comfortable operation. Ideal for cleaning facilities, equipment, and devices in workshops or industrial settings.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI