Campbell Hausfeld VT470200KB Owner's manual

Brand: Campbell Hausfeld

Model: VT470200KB

Category: Air compressors

Type: Owner's manual

This manual is also suitable for

VT6333

See Warranty on page 8 for Important information about commercial use of this product.

Portable Air

Compressors

Description

Air €ompressor units are intended to

provide compressed air to power

pneumatic toob and operate spray

guns. The pumps on these units are oil

lubricated. A small amount of oil

carryover ispresent in the compressed

air stream. Applications requiring air

free of oil or water should hove the

appropriate filter installed, The air

compressor unit must he mounted on a

solid floor or solid ground. Any other

use of these units will void the

warranty and the manufacturer wig not

be responsible for problems or

damages resulting from such misuse.

Safety Guidelines

This manual contains information that

isvery important to know and

understand. This information is

provided for SAFETY and to PREVENT

EQUIPMENT PROBLEMS. To help

recognize this information, observe the

following symbols.

_ Danger _ates

Inlu_€.

• poesnt;_

I_u_.

Unpacking

After unpacking the unit, inspect

carefully for any damage that may have

occurred during transit. Make sure to

tighten fittings, bolts, etc., before

putting unit into service.

DO not operate

unit if dam_

_ m_y mult in bwst_ a_l

cause inju_y or pr_rry damaSW.

General Safety

Information

Since the air compressor and other

components (material pump, spray

guns. filters, lubricators, hoses, eta-)

used, make up a high pressure

pumping system, the following safety

precautions must be observed at all

times:

1. Read all manuals _" _ ]

included with this |

product carefully, Be[

thoroughly familiar

with the controls

and the proper use of the

equipment.

2. Follow all local electrical and safety

codes as well as in the United States,

the National Electrical Codes (NEC)

and Occupational Safety and Health

ACt (OSHA).

3. Only persons well acquainted with

these rules of safe operation should

be allowed to use the compressor.

4. Keep visitors away and NEVER allow

children in the work area.

5. Wear safety glasses and use

hearing protection when operating

the unit.

6. Do not stand on or use the unit as

a handhold.

Breathable Air Warning

This compressor/pump Is NOT

equipped and should NOT be used

"as is" to supply breathing quality

air° Fo_"any applkation of air for

human consumption, you must fit

the air €ompressor/l_m p with

suitable in4ine safety and a_ann

equipmenL This edditional

equipment is necessary to properly

filter and purify the air to meet

minimaJ specifications for Grade D

breathing as described in

Compressed Gas AssodaUon

Commodity Specifkation G 7.1 -

1966, OSHA 29 CFR 1910. 1340

and/or Canadian Standards

Associations(CSA).

DISCLAIMER OF WARRANTIES

In the event the compressor is used

for the pu_ose of breathing air

application and proper ir_line

safety and alarm equipment is not

simultaneously used, existing

warranties are void, and Campbell

Nausteld disclaims any IJability

whatsoever for any loss, personal

injury or damage.

7. Before each use, inspect compressed

air system and electrical

components for signs of damage.

deterioration, weakness or leakage.

Repair or replace defective items

before using.

8. Check all fasteners at frequent

intervals for proper tightness.

I REMINDER: Keep your dated p_oof of i_lrdtase fro"warranty purpoml Attach It to this manual fill it for I

saf_ke4_tg.

O 2002 Campbell HausfeldFacott Fatzer _r parir_p_odu_&_r_k* inf=_matlon IN227809AV 12/02

visit www.¢hpower.€om

Portable Air Compressors

General Safety

Information (ConUnued)

store _e liquids or gases in the

vlrJnlty of the compressor.

_I,WARNING] _-

Never opera fe

€omplainer witl_l a

beit_J_rd. //ds _

start aufommtl_lly

wtlgtout warning.

Pen;onal Injury or property damage

could occur from €ont_--t with moving

9. Do not wear loose clothing or

jewelry that will get caught in the

moving parts of the unit.

Compre_or parlx my

be hot even If the unit

is stopped.

10. Keep fingers away

from a running

compressor: fast moving and hot

parts will cause injury and/or burns.

11. If the equipment should sta_ to

vibrate abnormally. STOP the

engine/motor and check

immediately for the cause.

Vibration isgenerally a warning of

trouble.

12. To reduce fire hazard, keep

engine/motor exterior free of oil,

solvent, or excessive grease.

_-_.I_NING- } ,_ _,_ _--',_-

the tank for _ comprmumr. The ASME

Jafe_ valve must have ,_ff_r_t flow

for maxJnwra opera,rig pressure. Do not

operate wt_ pr_aure _tt(h or p_int

v_/v_ set h/_er eum the _

13, Never attempt to adjust ASME

safety valve. Keep safety valve free

from paint and other

accumulations.

Never attempt to repair

or modify • tanki

Welding, drilling or any

obN_r modification will

weak_ the t_nk

resulting in damage from ruptur_ or

explosion. AIw=y_ replace worn, cracked

or damaged t:nk_

www.chpower.(om

Drain liquid from

] NOTICE ! ..k_

14. Tanks rust from moisture build-up.

which weakens the tank. Make sure

to drain tank regularly and inspect

periodically for unsafe conditions

such as rust formation and corrosion.

1S. Fast moving air will stir up dust and

debris which may be harmful Release

a_rslowly when draining moisture o¢

de_essudzing the €omp_ssor systen_

SPRAYING PRECAUTIONS

[&WARNING]

Do not _=my Rammab/e

16. Do net smoke whe_ spraying paint.

insecticides, or other flammable

substance_

17. Use a face

mask/respirator

when spraying and

spray in a well

ventilated area to

prevent health and

fire hazards,

18. Do not direct paint or ether sprayed

material at the compressor. Locate

compressor as far away from the

spraying area as possible to

minimize overspray accumulation

on the compressor.

19. When spraying or cleaning with

solvents or toxic chemicals, follow

the instructions provided by the

chemical manufacturer

_ARNING] _i--,_-_

and lock out power sourte, then

mI_ue a//pressu_

from the system before

attempUngtoins_//,

se_dce, re/ocab_ or

Jany

ma/ntenance.

Introduction

Refer to Figure I to locate the

following items.

Pressure switch - Auto/Off Switch - In

the "AUTO" position, the compressor

shuts off automatically when tank

pressure reaches the maximum preset

pressure. In the "off" position, the

compressor will not operate. This

switch should be in the "OFF" position

when connecting or disconnecting the

power cord from the electrical outlet or

when changing air tools. (See Figure 8.)

When the pressure switch turns the

motor off you will hear air leaking out

of the Pre_ure Switch Unloader Valve

for a short time. This releases the air

pressure from the discharge tube and

allows the compressor to restart easier.

Regulator - The regulator controls the

amount of air pressure in the air hose,

The air hose is attached at the outlet of

the regulator.

/_ME Safety Valve - This valve

automatically releases air if the tank

pressure exceeds the preset maximum.

Disdtarge tube * This tube carries

compressed air from the pump to the

check valve. This tube he¢ome_ v_rv hot

L WARNINGIToavoJdtherL kof

sev_n_ burns, n_ver

touch the d/scharge tube.

Check valve - One-way valve that

allows air to enter the tank, but

Discharge Tube

Check Valve Intake Filter

Handle

Belt

& Oil Fill Hole

Drain

Petcock

Flgur_ 1 (vertical unit not sho_m)

Portable Air Compressors

Introduction (Continued)

preventS air in the tank from flowing

back into the compressor pump.

Handle - Designed to move the

compressor.

handle to lift the

unit €omplexly off the groun_

Belt Guard- Covers the belt, motor

pulley and flywheel.

I'_WARNINGI H.=,,

operate €omprexJ_r

without • beltguarrL This

unit can start

aut_nab_al_l without

wRmln_ Penmmd _)u_ or property

damage could oc¢_ from _tact with

moving I_rl_

Tank Dtain Valve - This valve is

located on the bottom of the tank. Use

this valve to drain moisture from the

tank daily to reduce the dsk of

corr_ion.

Reduce tank pressure below 10 psi,

then drain moisture from tank daily to

avoid tank corrosion. Drain moisture

from tank{s) by opening the drain

valve located underneath the tank.

Tank Pressure Gauge - Indicates

amount of air pressure stored in tank.

Ho_e pressure Gauge - Indicates

amount of air pressure in hose used to

operate tools. This pressure is increased

or decreased by the regulator.

Assembly

HORIZONTAL TANK UNITS ONLY

HANDLE

t. Remove the handle screw from the

tank baseplate, if prainstalled.

2. Insert handle into both sides of tank

baseplate. Squeeze handle to fit Into

special openings in baseplate (See

Figure 2).

seplate

Handle \ ) _*_ Handle

_Screw

Bracket _ Rubber

_r_ Foot

Figure 2

3. Place a short piece of wood against

end of handle and tap with a mallet

or hammer untit the hole in the

handle lines up with the hole in the

baseplate.

4. Insert and tighten the handle screw

into the hole in the boseplate and

through the handle. Make sure the

screw goes through the handle.

WHEEL ASSEMBLY

The items marked with an asterisk (*) in

Figure 3 were shipped loose with the

unit. A_semble as follows:

1. Insert shoulder holt through wheel

hub with the bolt head on the

opposite side of the protruding hub

section.

2. For the 8 inch diameter wheels'

thsert the shoulder bob in the tow-

est hole of the tank axle iron and

tightly secure with Iocknut.

3, For the 10 ir_h diameter whaeLs,

insert the shoulder bolt in the upper

hole in the tank axle iron and

tightly secure with the Iocknut.

Repeat this step on the opposite

side.

Lock

Nut

* Wheel

Figure 3 - Wheel Assembly

When assembled, the tank must sit

level or slope slightly towards the tank

drain valve to allow tank to drain

properly.

VERTICAL TANK UNITS ONLY

HANDLE ASSEMBLY

Insert four handle screws through holes

in handle and tighten to tank baseplate

(See Figure 4).

FOOT ASSEMBLY

The items marked w;th an asterisk (*)

were shipped loose with the unit (See

Figure 5).

I. TBt unit to agow accessto front foot

and secure properly to ensure unit

does not tip over.

Handle

2. Insert bolt through foot and

bracket. The foot should be on the

lower side of bracket.

3. Tightly secure with the lock nut.

Repeat on opposite _de.

WHEEL ASSEMBLY

The items marked with an asterisk (*)

were shipped loose with the unit (See

Figure 5).

1. Insert shoulder bolt through wheel

hub. The bolt hex head should be

on the opposite skle of protruding

hub center.

2. Feed the shoulder bolt through the

hole on the tank axle iron and

tightly secure with the Iocknut.

Repeat on the opposite side.

Nut-

Figure 5 - Foot and Wlheel Assembly

LUBRICATION

before qp_radng comping.

Ensureoil drainextensionandcap has

been installed(if induded) then remove

the dipstickbreather(SeeFigure 6) and

fill pumpoil accordingto Chart 1.

OIL DRAIN EXTENSION

Some models include an oil drain

extension and cap (found with the owner's

manual). Install the oi] drain extendon and

cap before adding oil to the pta_p, TO

avoid oil leaks, it ishighly recommended

to apply Tefk_n° tape o_pz_te type sealant

to the threads on each end of the 0ii drain

extension. Screw the cap onto one end of

,,VWWld_power.com

)

Portable Air Compressors

Assembly (Continued)

the extension.Removethe oil drainplug

from _ baseof the pumpand installthe

o_ldrainextension(SeeFigure6).

Seespecificationlabelon air tank for

pump model number and refer to Chart

1for the proper oilcapacity.UseSAE30

industzialgrade air compressor oil or full

_nthetk motor o_1EkeMOI_ 1t0W-30.

Do not use regular automotive oil

as 10W-30. Additives in regular

motor oil cancausevalvedepositsand

reducepumplife, For maximum pump

life,drain and replaceoil after the first

hour of runtime. Proper oilFilllevel is

illu_a!.ed h_Figure6.

Dipstick

Breather _.

Add Oil Max Fult

Oil Drain Extension

Cap

Figure 6

/ VT4700_OKB

_q'470200KB

TC100OOOKB

I_ll ij ml *| LtlrT_ 1_1IrL1 • i ,] i,):_i,]1 I[1_1-_ ,

VS260000KB 6 oz

12 oz

11.5 oz

12 oz

Chart 1

WImNG

Local electrical wiring codes differ from

area *,o area. So_Tce wiring, plug and

protector must be rated for at least the

amperage and voltage indicated on

your motor nameplate, and meet Jail

electrical codes for this minimum. Use a

slow blow fuse type T or a circuit

breaker.

dm_t_ andf_ dama_

NOTE: 120 volt. 15 amp units can be

operated on a 120 volt 1S amp circuit

under the following conditions:

1. No other electrical appliances or

lightsare connectedto the same

branchdrcuit.

2. Voltage s_ppty b normal

3. Circuit isequipped with a 15amp

circuit breaker or a 15 amp slow

blow fuse Wpe T (ForCanada use

Type D).

If the above conditions cannot be met

or if nuisance tripping of the current

protection deviceoccurs,it may be

necessaq/to operate the compressor

from a 120 volt 20 amp circuit. Some

models convert to 240 volt operation,

seeDUALVOLTAGE MOTOR,

GROUNDING INSTRUCTIONS

1, This product must be grounded. In

the event of an electric short circuit,

grounding reduces the risk of

electrical shock by providing an

escape wire for the electric current.

Unit is equipped with a cord that has

a grounding prong, tt wil_ fit one of

the common outlet types shown in

Figure 7. If plug will not fit in the

desired outlet, have the plug or the

outlet replaced by a qualified

electrician.

GroundP;n GroundFin

GroundedOutlet

Figure 7

Improper use of grounding

plug can m_lt in I rlslk of

electrical shodt.

NOTE: DO not use grounding

adapter.

2. if repair or replacement of the cord

or plug isnecessary, do not connect

the grounding wire to either flat

blade terminal. The wire with

insulation having an outer surface

that isgreen with or without yellow

stripes is the grounding wire.

3. Check with a qualified electrician or

serviceman if the grounding

instructions are not ¢ompletety

understood, or if in doubt as to

whether the product is properly

grounded. Do not modify the plug

provided; if it will not fit the outlet,

havethe proper outlet installedby

a qualified electrician.

PLUGS AND RECEPTACLES

t. fl the pkKjonthe etectfical_d of

the unit isunfamiliar to youor will

not fit your particularreceptacle.

Figure7will help youunde_tand why

byillustratingthe different plugsand

the voltagesthey areto be usedwith.

2. Make surethat the product Is

connectedto anoutiet havingthe

sameconfigurationasthe plug.

3. Thereceptaclesmustbe €onnectedto

drcuitsrated to carryat_eastthe

voltagearidamperagesshown.

4. NEVERhavea receptaclereplaced

with one of ahigher amperage

beforedeterminingthe changecan

bemade accordingto allelectrical

codesaffectingyourpertJcuiararea.

The installationshouklbemade by a

qualifiedelectrician.If the pmdu_s

mustbe reconnectedfor useon

different_ypesofdrcuits,the re-

connectionshouldbemade by

qualifiedpersonnel.

DUAL VOLTAGE MOTORS [SOME

MODELS)

Dual voltage motors may be connected

for either t 20 volts or Z4O volts. By

comparing the plug on the cord with

the receptacles shown in Figure 7. you

can determine for which voltage your

compressor is factory wired. Also check

motor decal to change from low

voltage to high voltage.

_AWARNINGI ._led_,_,,_,__,

pe_ by •

qualified electr_dan,

To change connections for alternate

voltage:

1. Disconnect cord from power source

2. Remove motor terminal cover.

3. Find connection diagram on back

side of the cover or on motor

nameplate and reconnect to desired

voltage as indicated on diagram.

understand this

edring dM_ you must find •

4. Change plug to match voltage and

current requ_r emeuts.

www.chpower,_)rn

Portable Air Compressors

Assembly (Continued)

When €onverdng

Im _ aJsemmte

voltas_ be su_ _ gr**n grmmd wlr*

of the cowd _m_mttJ to the ground pln

of the plug _l to the metad body of

the preu_re swhth_

Operation

START-Up

I NOTICE I _ts'=_'=_

_mwtbe

filled With oil before :t_ See

lubrkatloe t4ctlo_

and _e unH checks OK.

1. Remove the dipstick breather and fill

pump to the proper oil level. See

Lubrication Section.

2. Open tank drain valve.

3. Turn pressure switch lever or knob

to OFF position and plug in power

cord.

4. Turn pressure switch lever or knob

to AUTO position and run unit for

30 minutes to break in the pump

parts (See Figure 8).

Knob

Aura'Off

Flgurt 8 Lever - Auto

5.Turn regulator knob fully

counterclockwise. Compressor will

build to maximum preset pressure

and shut off.

6. Turn regulator knob clockwise to

cause air to bleed off. Compressor

win restart at preset pressure.

7. Turn pressure switch lever or knob

to OFF position and unplug

powercord. Slowly turn regulator

knob clockwise to allow all air

pressure to be released. Do not

proceed to the next step until the

tank pressure reaches zero (0).

8. Attach hose, then add chuck or

other tool to open end of hose.

Plug in power¢ord. Turn pressure

switch lever to AUTO position.

When full pressure is reached turn

regulator knob clockwise until

desired outJet pressure is achieved.

9. After use, turn pressure switch lever

or knob to the OFF position.

10. If compressor is not used for a long

time period, bleed air from line and

use drain valve to drain water from

the tank, Then, follow the

maintenaoce s_hedule.

NOTE: Electric models are equipped

with a pressure switch that

automatically turns the motor OFF

when the tank pressure reaches a

preset level. After air isused from the

tank and drops to a preset low level,

the pressure switch automatically turns

the motor hack on.

Maintenance

_&WARNINGI

D/_onnect. tag a_d

IoG_ out power sour¢_.

then release ell

preJsure from the

sysllm_ before

at_mptlng to Itut_ll, servlcL relocat_

or perform any m_lnsen_e.

All repairs should be performed by an

authorized service representative.

FOR EFFlaENT OPERATION:

Perform the following test to verify

free operation of the safety valve

weekly and follow maintenance

schedule below.

t. Pull ring on safety valve and allow

the ring to snap back to normal

position (See Figure 9). This valve

automatically releases air if the tank

pressure exceeds the preset

maximum.

A large amount of

f_st moving alr wlll

be release if the safety valve Is

_tuJted with air pressure In the trunk,

valve. Thls valve should be checked

occaskmally. If air le_ks after the ring

ha= be4m released, or the valve Is stuck

and cannot be a¢luated by the ring. the

safety valve must he repl_ed.

2. With motor OFF and unplugged,

clean debris from motor, flywheel,

tank, air lines and pump cooling

fins.

MOISTURE IN COMPRESSED AIR

Moisture in compressedair will form

into droplets asit comesfrom an air

compressor pump. When humidity is

high or when a compressor isin

continuoususefor an extended

)eriod of time, this moisture will

collectin the tank. When usinga

paint sprayor sandblastgun,this

water will be carriedfrom the tank

through the hose,and out of the gun

as dropletsmixed with the spray

material.

Important: This condensation will

cause water spots in a paint job.

especially when spraying other than

water based paints. If sandblasting, it

will cause the sand to cake and clog

the gun, rendering it ineffective.

A filter or air dryer in the air line.

located as near to the gun es posdble.

will help eliminate moisture.

1/2" Deflection

DRIVE BELT

Belts will stretch in normal use. Properly

adjusted, a 5-pound pressure applied to

the belt between the motor pulley and

the pump will deflect the belt about

I/2" (See Figure 10).

TO ADJUST DRIVE BFLT:

1. Remove belt guard,

2. Loosen the four fasteners holding

the motor to the haseplate.

3, Shift the motor in the proper

direction, The belt must be properly

aligned when adjustment is made.

4. Adjust flywheel or motor pulley so

that the belt runs straight.

S. If necessary, use a gear puller to

move the pulley on the motor shaft,

Tighten setscrew after pulley is

positioned.

6. Attach belt guard.

STORAGE

1. When not in use, hose and

compressor should be stored in a

cool dry place,

www.chpower.com

Portable Air Compressors

2. Tanks should be drained of moisture

and hose should be disconnected

and hung with open ends down to

allow any moisture to drain.

3. Protect the electrical cord from

possible damage by winding the

cord loosely around the handle of

the unit or coiling the cord up.

Technical Support

For technical support regarding

operation or repair of this product.

please call 1-800-$43_400.

Check Oil Level

Drain Tank

Check Air Filter

Check Safety Valve

Clean Unit

Check Belt Tightness

Change Oil

Chart 2

VS 100-125 50-120

VT 225-300 50-120

TC 225-300 50-120

Chart 3

MAINTENANCE SCHEDULE

Troubleshooting Chart

....

Low discharge pressure 1. Air demand exceeds pump

capacity

2. AJr leaks

3. Restricted air intake

4. Blown gaskets

5. Leaking or damaged valves

1, Reduce air demand or use a compressor with more capacity.

2. Usten for escaping air. Apply soap solution to all flttings

and connections. Bubbles wdl appear at po nts of leakage.

Tighten or replace leaking fittings or connections_

3. Clean the air filter element.

4. Replace anygaskets proven faulty on inspection.

5. Remove head and inspect for valve breakage, misaligned

valves, damaged valve seats, etc. Replace defective parts and

reassemble.

_staJl. • new he_l gasket each time the

head is remove_

Pump overheating causes 1. Insulatinlg gasket between 1. Install gasket

air filter to melt filter andhead ismissing

2. Broken valves/blown gasket 2. Replace valves or install new gasket.

Excessive noise 1. Loose motor or compressor 1, of €omwesso_ knocking..,(knc<king) pulley Loose motor or corn ressor pulleys are a very commoncauseTightenpulley clamp bolts and set-

screw_

2. Lack of oil in crankcase 2. Check for proper oil level; if low. check for possible damage

to bearings. Dirty oil can cause excessive wear.

3. Worn connecting rod 3. Replace ¢onnectJng rod. Maintain oil level and change oil

more frequently.

4. Worn piston pin bores 4. Remove piston assemblies from the compressor and inspect

for excesswear. Replace excessively wornpiston pin or

pistons, as required. Maintain oil level and change oil more

freguequer_ly.

Remove the compressor head and valve plate and inspect for

carbon deposits or other foreign matter on top of piston.

5. Piston hitting the valve plate 5.

www.chpower.com

Troubleshooting Chart

Portable Air Compressors

Excessive noise Replace head and valve plate using new gasket. See

(knocking) Lubrication section for recommended oil.

Continued 6. Noisy check valve in 6. Replace.

compressor _stom . _ . Do not disassemble check valve with

rll wx_lvt-m_,l alr _ssure in tank

Large quantity of oil in 1. Worn piston rings 1. Replace with new rings. Maintain oil level and change oil

the dLsr,harge air more frequently.

NOTE: In an oil 2. Corn ressor air intake 2. Clean filter, Check for other restrictions in the intake system,

lubricated compressor r_r_ed

there will always he a 3. Excessive oil in compressor 3. Drain down to full level.

small amount of oil in the 4. Wrong oil viscosity 4. Use Mobil 1° lieN-30

air stream,

Water in discharge 1. Normal operation. The t. Drain tank more often. At least daily.

air/tank amount of water increases 2. Add a filter to reduce the amount of water in the air line.

with humid weather

Motor hums and runs 1. Use of extension cord 1. Do not use an extension cord. Use longer air hose with larger

slowly or not at ell diameter.

2. Malfunctioning check valve 2. Replace check valve, unloader valve or pressure switch.

orunloadervalve . _ . Do not dlsassembJe ched_ valve wlth

• 11 Wl_Ik't_ I -I il II_bWllSjIIIII B In

3. Low voltage 3. Check with voltmeter, check reset switch on motor. If reset

switch trips repeatedly, find and correct the cause. See next

item.

4. Repair or replace pressure switch.

Reset mechanism cuts out

repeatedly or fuses blow

repeatedly

4. Malfunctioning pressure

switch - contacts will not

dose

1. TOO many devices on same

circuit

2. Incorrect fuse size or circuit

breaker

3. Malfunctioning check valve

1. Limitthecircuitto the useof only the air compressor.

2. Besurethat fusesor circuitbreakersare rated properly.

3. Replacecheckvalve.

_)_'_'_ DO not disassemble chedc valve with

air _ssute in tank

4. Pressureswitch set too high 4. Ad ustor replace.

5. Loosewiring 5. Checka • ectrical connections.

6. Malfunctioning motor 6. Replacemotor.

Tank does not hold 1. Worn check valve 1, Replacecheckvalve.

DO not disassemble check valve With

pressure when _ air pressurt In tank

€ompressorsoff and the

shut off valve isclosed 2. Checkall connections and 2. Tighten.

fittings for leaks

3. Checktank for cracksor pin 3, Replacetank. Never repair a damaged tank.

holes

Pressureswitch 1, Malfunctioning checkvalve 1. Replace the checkvalveif the unJoadervalve bleedsoff

continuously blowsair constantly.

out the unloader valve _ DO not disassemb/e ched( valve with

a/r pressure in tank

Pressureswitchdoesnot 1. Malfunctioning unloader 1. Replacethe pressureswitchif it doesnot releasethe pressure

releaseair when the unit valve on pressureswitch for a short periodoftime when the unit shutsoff.

shuts off _ Donotdlsassemblepmssuteswit(h

with air pressure in tank

Excessivevibration 1. Loose fasteners 1. Tighten,

2. Belt needsreplaced 2. Replacewith correctsize.

3. Behalignment 3_Align flywheel and pulley.

www.dhpower.(om

Portable Air Compressors

Limited Warranty

1. DURATION: From the date of purchase by the original purchaser as follows: Standard Duty - One Year. Serious Duty - Two

Yean¢ Extreme Duty - Three Years; Maxus Model Series - Five Years.

2. WHO GIVES _-IIS WARRANTY (WARRANTOR):

Campbell Hausfeld I Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6400

3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell

Hausfeld compressor.

4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld air compressor.

S. WHAT ISCOVERED UNDER THIS WARRANTY: SubstanUal defects due to material and workmanship with the exceptions noted

below.

6. WHAT IS NOT COVERED UNDER THiS WARRANTY:

A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE

DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this compressor is used for commercia I_industrial or rental

purposes, the warranty will apply for ninety (90) days from the date of purchase. Extreme Duty Contractor Compressors are

not limited to a ninety (90) day warranty when used in contractor applications. Four cylinder single-stage and two-stage

compressors are not limlted to a ninety (90) day warranty when used in commercial or industrial applications. Some States

do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

g. ANY INCIDENTA 1 iNDIRECT. OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT,

FAILURE. OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion or

limitations of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

C. Any failure that results from an accident, purchaser's abuse, neglect or failure to operate products in accordance with

instructions provided in the owner's manual(s) supplied with compressor.

D. Pre-delivery sen/ice, i.e. assembly, oil or lubricants, and adjustment.

E. items or service that are normally required to maintain the product, i.e. lubricants, filters and gaskets, etc.

F. Gasoline engines and components are expressly excluded from coverage under this limited warranty. The Purchaser must

comply with the warranty given by the engine manufacturer which is supplied with the product.

G. Additional items not covered under this warranty:

1. All Compressors

a. Any component damaged in shipment or any failure caused by installing or operating unit under conditions not in

accordance with installation and operation guidelines or damaged by contact with tools or surroundings.

b. Pump or valve failure caused by rain, excessive humidity, corrosive environments or other contaminants.

c. Cosmetic defects that do not interfere with compressor functionality.

d. Rusted tanks, including but not limited to rust due to improper drainage or corrosive environments.

e. Electric motors, check valves and pressure switches after the first year of ownership.

f. Drain cocks.

g. Damage due to incorrect voltage or improper wiring.

h. Other items not listed but considered general wear parts.

L Pressure switches, air governors and safety valves modified from factory settingr_

2. Lubricated Compressors

a. Pump wear or valve damage caused by using oil not specified.

b. Pump wear or valve damage caused by any oil contamination or by failure to follow proper oil maintenance

guidelines.

3. Belt Drive / Direct Drive ! Gas Driven Compressors

a. Be_ts.

b. Ring wear or valve damage from inadequate filter maintenance.

c. Manually adjusted Ioacl/unload and throttle control devices.

7. RESFONSIBIUTIES OF WARRANTOR UNDER THIS WARRANTY; Repair or replace, at Warrantor's option, compressor or

component which isdefective, has malfunctioned and/or failed to conform within duration of the warranty pedod.

8. RESPONSIBIUTIES OF PURCHASER UNDER THIS WARRANTY:

A. Provide dated proof of purchase and maintenance records.

B. Portable compressors or components must be delivered or shipped to the nearest Campbell Hausfeid Authorized Service

Center. Freight costs, if any, must be home by the purchaser.

C Use reasonable care in the operation and maintenance of the products as described in the owner's manual(s).

9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be

scheduled and serviced according to the normal work flow atthe servicing location, and depending on the availability of

replacement parts.

This Limited Warranty applies in the U.S., Canada and Mexico only and gives you specific legal rights. You may also have

other rights which vary from State to State or country to country.

www.dlpower,com

Page is loading ...

Campbell Hausfeld VT470200KB Owner's manual

Brand: Campbell Hausfeld

Model: VT470200KB

Category: Air compressors

Type: Owner's manual

This manual is also suitable for

VT6333

Download PDF

report

in other languages

français: Campbell Hausfeld VT470200KB Le manuel du propriétaire
español: Campbell Hausfeld VT470200KB El manual del propietario

Campbell Hausfeld VT470200KB Owner's manual

This manual is also suitable for

Campbell Hausfeld VT470200KB Owner's manual

in other languages

Related papers

Other documents