Supermicro P3TDDR Quick Reference Manual

Type
Quick Reference Manual
Motherboard Components
1 System Board
2 JPA2
3 Adaptec AIC-7899
4 JPA1
5 Ultra160 LVD SCSI CH A
6 South Bridge
7 Battery
8 SCSI LED
9 WOL1
10 WOM1
11 JBT1
12 JP8
13 JUSB1
14 J10 IRDA
15 IDE#1, IDE#2
16 Floppy
17 BIOS
18 Chassis Fan2, 3
19 Chassis Fan1
20 JF1
21 JP11, Overheart Fan, J7
22 DIMM 1, 2, 3, 4
23,24 CPU Fan 1,2
25 CPU 1
26 CPU 2
27 North Bridge
28 ATX Power Conn.
29 JP1: JPWAKE
30 Mouse and Keyboard Connectors
31 USB1, USB2
32 COM1 Port, VGA Port
33 Printer Port
34 ATI VGA
35 NIC 1, NIC2
36 JP10
37 JP3
38 JP6, JP7
39 JPL1
40 PCI 1, PC2, PCI 3
41 JPL2
42 Ultra160 SCSI Conn.
43 Ultra160 SCSI LVD CH B
44 JP2
45 Raptor Slot
4
3
1
2
36
31
29
5
26
17
15
14
13
34
40
10
32
7
6
8
9
24
22
20
39
16
37
19
21
33
44
43
41
42
23
25
35
38
18
28
27
30
11
12
45
Front Panel Functions
1. Hot-plug SCSI hard drive, SCSI ID 0
2. Hot-plug SCSI hard drive, SCSI ID 1
3. 1 Slim CD-ROM
4. 1 Floopy Drive
5. Overheat: Indicates an overheat condition in the system
6. NIC2: Indicates network activity on LAN2 when flashing
7. NIC1: Indicates network activity on LAN1 when flashing
8. HDD: Indicates IDE channel activity.
9. Power: Indicates power is being supplied to the system's
power supply units
1
2
4
3
5
6
7
8
9
P3TDDR Quick Reference
Jumpers Description Default Setting
JBT1  CMOS Clear Pin 1-2 (Normal)
JPA1/2  SCSI CHA/B Termination Open
JPWAKE(JP1) Keyboard Wake-UP Pin 1-2 (Disabled)
JP2  SCSI Pin 1-2 (Enabled)
JP3 VGA Pin 1-2 (Enabled)
JP8  Speaker Pins 1-2 (Enabled)
JP10 VGA IRO Pins 1-2 ( Enabled)
JPL1/2 LAN 1/2 Closed (Enabled)
To protect the system and components, it is essential that you reinstall the top panel after you have finished working on the system.
Due to the fact that adequate air flow and proper thermal control are
very critical in maintaining 1U system's stability and performance, it is
imperative that the proper installation procedures listed below be
followed in order to maximize system performance. This is especially
critical for 1U Dual Processor Servers with speeds of 1 GHz and above.
Warning !
CPU Heat Sink Installation Procedures
(For Supermicro SuperServer 1U Systems)
Cooling Fan Installation
Rear Panel Functions
1. AC Power connector
2. 2 x Intel 82559 LAN ports
3. 64/32-bit Expansion Slot
4. PCI Card Release Latch
5. Ultra160 SCSI Connector
1) Only those CPU heat sinks that are provided by Supermicro should be used.
2) Apply a small amount of silicon compound on the CPU's die.
3) Place the CPU heat sink on top of the CPU.
4) Place the heat sink spring on top of the CPU heat sink and secure the clip of
the spring into its notch. (Make sure the clip position is the same as the  
picture shown above.)
6. PS/2 Mouse and Keyboard port
7. 2 USB ports
8. Printer Port
9. 2 COM ports ( 1 internal)
10. 1 VGA port
clip
clip
2
1
CPU2
CPU1
6
7
8
9
10
1
2
3
4
5
  • Page 1 1
  • Page 2 2

Supermicro P3TDDR Quick Reference Manual

Type
Quick Reference Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI