DPA 4006 Omnidirectional Microphone User guide

Type
User guide

This manual is also suitable for

DPA 4006 Omnidirectional Microphone

The DPA 4006 is a high-quality omnidirectional microphone designed for a wide range of recording applications including film, television, music, and more. With its wide frequency response, exceptional sound quality, and rugged construction, the 4006 is a versatile microphone that can be used in a variety of challenging environments.

The 4006 features a pressure-gradient design with a pre-polarized condenser capsule. This design provides the microphone with a smooth, natural sound quality with excellent transient response. The microphone also has a low self-noise of just 15 dB(A), making it ideal for recording in quiet environments.

DPA 4006 Omnidirectional Microphone

The DPA 4006 is a high-quality omnidirectional microphone designed for a wide range of recording applications including film, television, music, and more. With its wide frequency response, exceptional sound quality, and rugged construction, the 4006 is a versatile microphone that can be used in a variety of challenging environments.

The 4006 features a pressure-gradient design with a pre-polarized condenser capsule. This design provides the microphone with a smooth, natural sound quality with excellent transient response. The microphone also has a low self-noise of just 15 dB(A), making it ideal for recording in quiet environments.

4006A Omnidirectional Microphone
A combination of the MMC4006 Microphone Capsule and the MMP-A
preamplifier, this mic is part of DPAs recording microphone series.
Attenuation Pad
The MMP-A preamplifier has a 20dB attenuation push-
switch at the XLR connector. Use a pencil or the like to
activate the attenuator and lower the output by 20 dB.
Grids
The 4006A is supplied with three dierent grids that are used to change
the characteristics of the microphone acoustically. Be extremely careful not
to touch the exposed diaphragm when switching grids. Do not attempt
to remove dust. The performance of the microphone is not aected
by dust.
dpamicrophones.com/4006A
DPI-4006A-QG
1
0
Hz
50
2
0
1
00
2
00
500
1 kHz
5
10
20
40
dB
1
0
-
1
0
-
2
0
-30
0
On-axis
Diuse
10 Hz 5020 100 200
500
1 kHz 2510 20 40
dB
10
-10
-20
-30
0
On-axis
Diuse
10 Hz 5020 100 200
500
1 kHz 2510 20
40
dB
10
-10
-20
-30
0
The pre-mounted silver near-field grid (DD0251) exhibits neutral frequency
response when used in near sound field (direct sound field).
The black diuse-field grid (DD0297) oers recording accuracy in diuse
sound field (far field) by compensating for the natural high frequency loss caused by air absorption.
The silver trapezoid close-mic grid (DD0254) subtly rolls o the highest frequencies
to create a smoother treble response when close miking sources with bright transient impulses.
Service & repair
If you are not satisfied with the characteristics exhibited by this product, please go to
www.dpamicrophones.com/service for instructions.
Warranty
The 4006A is covered by a five-year limited warranty.
CE marking
This product conforms to all relevant directives approved by the European Commission.
Specifications
Directional pattern
Omnidirectional
Principle of operation
Pressure
Capsule type
Pre-polarized condenser
Frequency response
10 Hz - 20 kHz
Eective frequency range ±2 dB
10 Hz to 20 kHz
Sensitivity, nominal, ±2 dB at 250 Hz
40 mV/Pa, -28 dB re 1 V/Pa
Equivalent noise level, A-weighted
Typ. 15 dB(A) re. 20 µPa (max. 17 dB(A))
Switchable attenuator, filters etc.
0 dB / -20 dB
Rated output impedance
< 200 Ω
Output balance principle
Impedance balancing with Active Drive
Common Mode Rejection Ratio (CMRR)
> 60 dB
Power supply (for full performance)
P48 (Phantom Power)
Current consumption
2.8 mA
Polarity
+V at Pin 2 for positive sound pressure
Connector
XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
Weight
163 g (5.7 oz)
Operating temperature range
-40 to 45°C (-40 to 113°F)
Relative humidity
Up to 90%
  • Page 1 1
  • Page 2 2

DPA 4006 Omnidirectional Microphone User guide

Type
User guide
This manual is also suitable for

DPA 4006 Omnidirectional Microphone

The DPA 4006 is a high-quality omnidirectional microphone designed for a wide range of recording applications including film, television, music, and more. With its wide frequency response, exceptional sound quality, and rugged construction, the 4006 is a versatile microphone that can be used in a variety of challenging environments.

The 4006 features a pressure-gradient design with a pre-polarized condenser capsule. This design provides the microphone with a smooth, natural sound quality with excellent transient response. The microphone also has a low self-noise of just 15 dB(A), making it ideal for recording in quiet environments.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI