Easy Start Guide
HL113EW | Homeplug AV Wireless-N Extender
- HL113EW - Easy Start Guide
- Ethernet Cable - Warranty Card
- Resource CD
B Device Overview
A Package Contents
In Room A, plug in your HomePlug AV device into a
power outlet and connect it to your router’s ethernet
port using an ethernet cable.
Make sure that your router’s internet connection is
up to allow you to access the internet.
1.
Ensure to follow the connection set up below.
D Conguring Wireless Settings (Optional)
In Room B, plug in your HL113EW device into a
power outlet. You may connect any device (e.g.
computer / notebook) to its ethernet port; you may
also connect any of your wireless devices via WiFi
(SSID and Password is printed at the label sticker
located at the top surface of your HL113EW).
Conrm that a connection was established on both
HomePlug AVs. Successful connection is indicated
by Green light on both Power and Power Line
Activity LEDs. Your Homeplug AV is now ready to
use and may now access the internet.
2.
3.
C Setup for New Network Connection
Connect an Ethernet cable from your computer to any
of the available Ethernet Ports of your HL113EW.
On your computer, turn OFF your device’s Wireless
Adapter (if applicable).
Open and Launch a web browser. Type in 10.0.10.254
1.
2.
3.
on the web browser’s url link then press enter.
Enter admin for Username and admin for Password.
Select the Wireless tab to modify the wireless
settings.
After changing the preferred settings, click Apply to
save.
4.
5.
6.
Simple
Connect
Button
Power
LED
Ethernet
LED
Ethernet
Ports
Best
(Green)
Connection rate
is more than
80 Mbps
Better
(Amber)
Connection rate is
between 30 to
80 Mbps
Good
(Red)
Connection rate
is less than
30 Mbps
Power Line Activity LED
Represents your HL117EW’s connection rating
HL113EW
WPS
Button /
Wireless
LED/
Reset
Button
E Setup for an Existing Network Connection
Press the Simple Connect Button of the Old device
for two (2) seconds. The Power LED will start
blinking.
On the HL113EW, press the Simple Connect
button for two (2) seconds. The Power LED will
start blinking and the Power Line Activity LED will
be on steady green, indicating a succesful pairing
with the old devices.
b.
c.
Ensure that you have the proper set up as indicated
in Section D (Conguring Wireless Settings). Follow
steps 3 and 4 respectively of Section D.
In the Web User Interface, click the Wireless tab,
choose Security, enable the WPS, then click Apply.
On your HL113EW, press the WPS button for two (2)
seconds. The Wireless LED will start to blink slowly.
Press the WPS button on the device that you wish
to connect to HL113EW. Complete steps 3 and
4 of this section within two minutes to ensure a
succesful connection .
1.
2.
3.
4.
F Enabling the WPS Function (Optional)
G Determining Connection Rate
Each LED color of the Powerline Activity LED represents
a connection rating. The connection rating can only
be calculated when the device is part of an existing
network. The exact connection rate value can also be
viewed using the HomePlug AV Web User Interface.
Good (Red)
Better(Amber) Best(Green)
Connection rate is
less than 30 Mbps
Connection rate is
between 30 to 80 Mbps
Connection rate is
more than 80 Mbps
H Device Reset
To restore the HL113EW to its
Default Factory Settings, press the
WPS button for five (5) seconds
then release. The LEDs will turn off
and turn on to indicate the reset of
the device.
* The HL113EW Easy Start Guide is designed to get you
up and running with your HL113EW device. This Easy
Start Guide along with the User Manual which provides a
more advanced guide to this product is included in the CD
and is also downloadable on our Aztech Support Website
(www.aztech.com/support).
If you want to add your HL113EW device to your
existing network, simply plug in the device to any
power outlet; by default it will pair up with your
HomePlug AV devices. Once paired, your device is
now ready to use.
However, just in case you have changed the Private
Network Name of your existing network, you may
use the Simple Connect button of HL113EW and the
old devices as indicated below:
1.
2.
Press the Simple Connect Button of the
HL113EW for ten (10) seconds until the Power
Line Activity LED turns off and ON.
a.
Press for 5 SECONDS
to perform factory
default reset.
-
1
-
2
