Banner VE202G1A is a self-contained smart camera with user-friendly Vision Manager software. It offers high-resolution 2 MP grayscale images (1600 x 1200 pixels) for precise inspection tasks. With various image processing tools and capabilities, it can solve a wide range of vision applications, including item detection, part positioning, feature measurement, and flaw analysis. The intuitive Vision Manager software allows for easy setup, run-time editing, and offline troubleshooting.
Banner VE202G1A is a self-contained smart camera with user-friendly Vision Manager software. It offers high-resolution 2 MP grayscale images (1600 x 1200 pixels) for precise inspection tasks. With various image processing tools and capabilities, it can solve a wide range of vision applications, including item detection, part positioning, feature measurement, and flaw analysis. The intuitive Vision Manager software allows for easy setup, run-time editing, and offline troubleshooting.
Quick Start Guide
Self-contained Smart Camera with User-Friendly
Vision Manager Soware
This guide is designed to help you set up and install the VE Series Smart Camera. For complete informaon on programming, performance,
troubleshoong, dimensions, and accessories, please refer to the Instrucon Manual at www.bannerengineering.com. Search for p/n 191666 to view the
Instrucon Manual. Use of this document assumes familiarity with pernent industry standards and pracces. More details are available in the online
help.
WARNING: Not To Be Used for Personnel
Protecon
Never use this device as a sensing device for personnel protecon. Doing so could lead to serious injury or death. This device
does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applicaons. A sensor failure
or malfuncon can cause either an energized or de-energized sensor output condion.
CAUTION:
Electrostac Discharge
Avoid the damage that electrostac discharge (ESD) can cause to the Sensor.
Always use a proven method for prevenng electrostac discharge when installing a lens or aaching a cable.
CAUTION: Hot Surface
Use
cauon when handling the camera. The surface of the camera may be hot during operaon and immediately aer use.
Models
Model
1
Resoluon
VE200G1A WVGA, 752 × 480 pixels grayscale
VE201G1A 1.3 MP, 1280 × 1024 pixels grayscale
VE202G1A 2 MP, 1600 × 1200 pixels grayscale
Features
1
2
3
4
5
7
6
8
9
Figure 1. Sensor Features
1. Display
2. Buons
3. Pass/Fail indicator (green/red)
4.
Ready/Trigger indicator (green/amber)
5. Power/Error indicator (green/red)
6. Ethernet indicator (amber), not shown
7. Ethernet connecon
8. Light connecon
9. Power, Discrete I/O connecon
1
Model VE202G2A, 2 MP, 1600 × 1200 grayscale with 4-pin D-code M12 Ethernet connecon is also available.
VE Series Smart Camera
Original Document
191667 Rev. E
7 June 2017
191667
Display
Figure 2. Display with Home Screen
The display is a 2-line, 8-character LCD. The main screen is the Home
Screen, which shows the name of the current inspecon and the slot
number (inspecon locaon). Use the display to view or change several
sensor sengs.
Indicators
Four LED indicators provide ongoing indicaon of the sensing status.
Power/Error Indicator
Green = Normal operaon
Red = System error
Ready/Trigger Indicator
Green = Ready for trigger
Yellow = Trigger is acve
OFF = Not ready for a trigger, triggers will be missed
Pass/Fail Indicator
Green = Previous inspecon passed
Red = Previous
inspecon failed
OFF = No trigger since power up
Ethernet Indicator
Amber solid = Ethernet connecon
Amber ashing = Ethernet
acvity
OFF = no connecon
Buons
Use the sensor buons Down
, Up , Enter , and Escape to congure several sensor sengs and to access sensor informaon. See
Figure 11 on page
10 for addional informaon on using the buons.
Vision Manager Soware
Set up the VE Series Smart Camera using the free Vision Manager Soware, available for download at www.bannerengineering.com.
This easy-to-use image processing soware provides a variety of tools and capabilies to solve a wide range of vision applicaons such as item detecon,
part posioning, feature measurement and aw analysis. Run-me
eding allows you to make changes to an inspecon while the sensor is running,
reducing costly downme. Vision Manager also includes a full soware emulator, allowing users to develop or troubleshoot inspecons oine, without a
sensor.
Installaon
Instrucons
Install the Accessories
1
2
3
5
4
Figure 3. Install the Accessories
1. VE sensor
2.
O-ring (used with the lens cover)
3. C-mount lens (available separately)
4. Filter
(oponal)
5. Lens cover (oponal)
An external light (oponal) is not shown.
Note: A lens cover and a ring light cannot be used together.
1. If you are using a lens cover: Remove the black thread protector (not shown) from the sensor (1).
2.
If you are using a lens cover: Fit a single o-ring (2) into the undercut area behind the sensor threads.
3. Remove the yellow temporary imager cover (not shown) from the sensor.
CAUTION: Do not remove the imager cover unl you are ready to install the lens. Do not touch the imager. Dirt or dust
on the imager can
aect sensing reliability.
4. Remove any protecve covers from the lens. Handle the lens carefully to avoid smudges and dirt on the opcal elements.
5.
Thread the lens (3) onto the sensor.
6. Make sure that the lens is focused; see Acquire a Good Image on page 6.
7. Use the thumbscrews on the lens to lock the focus and aperture rings and to prevent movement that can occur during cleaning or accidental
contact.
8. If you are using a lter: Thread the
lter (4) onto the front of the C-mount lens.
9. If you are using a linear polarizaon
lter: Rotate the outer poron of the lter mount to determine the posion where glare is reduced the
most, and use the locking thumbscrew to fasten the lter in posion.
VE Series Smart Camera
2 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 191667 Rev. E
10.If you are using a lens cover: Thread the lens cover (5) onto the threaded poron of the sensor.
11.
Or, if you are using an external light bracket: Aach an external light bracket to the sensor using the provided hardware kit.
Note: For opmal imaging, provide adequate dissipaon of heat. A good heat conductor, such as aluminum, may be required.
Mount the Sensor
1.
If a bracket is needed, mount the sensor onto the bracket.
2. Mount the sensor (or the sensor and the bracket) to the machine or equipment at the desired locaon. Do not ghten the mounng screws at
this me.
3. Check the sensor alignment.
4.
Tighten the mounng screws to secure the sensor (or the sensor and the bracket) in the aligned posion.
Connect the Cables
1
2
3
4
Figure 4. Cable Connecons
1. Power, Discrete I/O connecon
2. Light connecon
3. Ethernet connecon
4. Ethernet indicator
1. Connect the Ethernet cable to the sensor (3) and to the computer or Ethernet switch.
2.
Connect the power, discrete I/O cable to the sensor (1), and the leads to the appropriate locaons. See Table 1 on page 3 for the power,
discrete I/O connecons.
3. Connect the external light cable (oponal) to the light connecon (2) if the light is powered by the sensor.
CAUTION: Use Appropriate Power
If the light is powered by the sensor, the sensor power source must be 24 V dc. This connecon is for Banner lights only.
Table 1: Power and I/O Pinouts
Pin Wire Color Descripon Direcon
1 White Discrete I/O #3 Input/Output
2 Brown 12 V dc to 30 V dc Input
3 Green I/O output common
Important: For PNP (sourcing) outputs connect pin 3 to +V dc, for
NPN (sinking) outputs connect pin 3 to 0 V dc. The discrete I/O pins
are 1, 5, 8, 10, and 11.
-
4 Yellow RS-232 TX (transmit) Output
5 Gray Discrete I/O #5 Input/Output
6 Pink Trigger input Input
7 Blue Common Input
8 Red Discrete I/O #2 Input/Output
9 Orange I/O input common
Important: For PNP (sourcing) inputs connect pin 9 to 0 V dc, for NPN
(sinking) inputs connect pin 9 to +V dc. The discrete I/O pins are 1, 5,
6, 8, 10, and 11.
-
10 Light Blue Discrete I/O #4 Input/Output
11 Black Discrete I/O #1 Input/Output
12 Violet RS-232 RX (receive) Input
Shield Bare metal Chassis ground -
VE Series Smart Camera
P/N 191667 Rev. E www.bannerengineering.com - Tel: +1-763-544-3164 3
Wiring Diagrams
VE
Load
+
-
12-30V dc
Output
Power
Supply
Output Common
VE Output
Figure 5. PNP Output
VE
+
-
12-30V dc
Output Common
VE Output
Load
Output
Power
Supply
Figure 6. NPN Output
VE
Input Common
+
-
VE Input
Opto-isolator
12-30V dc
PNP Driver
Input
Power
Supply
Figure 7. PNP Input
VE
Input Common
+
-
VE Input
12-30V dc
Opto-isolator
Input
Power
Supply
NPN Driver
Figure 8. NPN Input
Install the Soware
PC Requirements
Operang System
Microso
®
Windows
®
operang system version 7, 8, or 10
2
System Type
32-bit, 64-bit
Hard Drive Space
80 MB (plus up to 280 MB for Microso .NET 4.5, if not already installed)
Memory (RAM)
512 MB minimum, 1 GB+ recommended
Processor
1 GHz minimum, 2 GHz+ recommended
Screen Resoluon
1024 × 768 full color minimum, 1650 × 1050 full color recommended
Third-Party Soware
Microso .NET 4.5, PDF Viewer (such as Adobe Acrobat)
USB Port
USB 3.0, recommended if a USB to Ethernet adapter used to communicate with the
sensor
Important: Administrave rights are required to install the Vision Manager soware.
1. Download the latest version of the soware from www.bannerengineering.com.
2. Navigate to and open the downloaded le.
3. Click Next to begin the installaon process.
4. Conrm the soware
desnaon and availability for users and click Next.
5. Click Install to install the soware.
6. Depending on your system sengs, a popup window may appear prompng to allow Vision Manager to make changes to your computer. Click
Yes.
7.
Click Close to exit the installer.
Geng Started
Power up the sensor, and verify that the power/error LED is ON green and that the Ethernet indicator is ON amber to verify the Ethernet connecon.
Connect to the Sensor
These instrucons use Windows
®
operang system version 7, 8, or 10.
3
2
Microso and Windows are registered trademarks of Microso
Corporaon in the United States and/or other countries.
3
Windows is a registered trademark of Microso
Corporaon in the United States and/or other countries.
VE Series Smart Camera
4 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 191667 Rev. E
1. Conrm the network connecons.
a) Click the Start buon, then on the Start menu, click Control Panel.
b)
In Control Panel, click Network and Internet, then click Network and Sharing Center, and then click Change adapter sengs.
c)
Right-click on the connecon that you want to change, then click Properes.
If you are prompted for an administrator password or conrmaon, enter the password or provide conrmaon.
d) In the connecon
properes, click Internet Protocol Version 4 (TCP/IPv4), and then click Properes.
e) In the Internet Protocol (TCP/IPv4) Properes, select Use the following IP address.
f)
Make sure that the IP address is 192.168.0.2, and the subnet mask is 255.255.255.0.
2. Open Vision Manager from the desktop or the Start menu.
The Sensor Neighborhood tab displays and lists the available sensors.
3.
From Sensor Neighborhood, click
to connect to the desired sensor.
The status changes from Available
to Connected and the Sensor screen displays. Click to disconnect from the sensor.
4.
If the desired sensor is not listed, verify that:
• The network adapter connected to the sensor has the same subnet mask as the sensor (for example, 192.168.0.xxx); view the subnet mask in
the Network Adapters list at
Home > Sensor Neighborhood > Network Adapters
•
The Ethernet cable is the correct type
• The TCP/IPv4 sengs are correct
Or, manually enter the sensor's IP address.
Note: The sensor's IP address and subnet mask are also available from the sensor display.
VE Series Smart Camera
P/N 191667 Rev. E www.bannerengineering.com - Tel: +1-763-544-3164 5
Sensor Screen
The Sensor screen displays the informaon needed to create or modify an inspecon.
1. Screens—Home, Sensor, Inspecon Logs, Inspecon Management, System Sengs
2. Manual Trigger buon—Click to manually trigger the sensor
3. Inspecon list—Select the desired inspecon to start, and to view or modify the inspecon
4. Summary pane—Includes the Inspecon Summary, the I/O Summary, and the Test Summary
5. Parameters pane—Includes user-adjustable Inputs parameters or Test parameters for the tools in an inspecon, depending on what is selected in the Tools and Results pane
6. Tools and Results pane—Includes Tools and Results, Tools Only, and All Results, which display the camera tool, the tools that are included in the current inspecon, and the
results of the inspecon
7. Image Pane Parameters panel—Includes ROI view buons, zoom, x and y coordinates, grayscale value, sengs buon, and full image display buon, as well as sensor messages
8. Image pane—Displays the current image captured by the sensor; this includes the region of interest (ROI) for the tool for the selected inspecon
Figure 9. Sensor Screen
Acquire a Good Image
The sensor needs to capture a good image of each part to ensure that it correctly passes good parts and fails bad parts.
1.
Make sure that the lighng is appropriate for your target. Use supplementary lighng, such as a ring light, if necessary.
2.
Click the
Sensor screen.
3.
Click the camera tool on Tools and Results.
The Inputs parameters display.
4.
Set the trigger.
a) Expand the Trigger parameters.
b) In the Trigger Mode list, click Internal (connuous images).
5.
Run Auto Exposure.
a) Expand the Imager parameters.
b) Expand the Auto Exposure parameters, and click Start to run.
6. Check the lighng on the part.
•
Make sure that the lighng is constant and consistent (unchanging over me, no shadows or hot spots)
• Capture the shape and form of the target object with lighng that opmizes its contrast and separates the feature of interest from the
background. Depending on the target, consider other Banner lights
•
Adjust the mounng angle to provide the clearest image of the part features you are inspecng
7. Aer checking and adjusng the
lighng, run Auto Exposure a second me or adjust the exposure manually by expanding the Exposure
parameters and moving the slider or entering a specic exposure me.
VE Series Smart Camera
6 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 191667 Rev. E
8. Adjust the focus.
a)
Place the part so that the area to be focused appears in the center of the Image pane.
b) Expand the Focus Info parameters.
c) Make sure that the Focus Info checkbox is selected.
d) Adjust the focus of the lens while monitoring the focus number.
The focus number is a number between 1 and 255. Use the Image pane to determine when the image is sharp enough, or use the focus
number as a guide. Turn the focus ring on the lens unl the focus number is at the highest possible number between 1 and 255. The focus
number is also available on the sensor display.
Note: There is no opmal value for this number, but it can be used as a guide if you are seng up more than one
sensor that are focused on the same target.
e) Tighten the locking thumbscrews to secure the lens at the desired focus.
Set Up an Inspecon
Vision Manager allows you to set up or make changes to an inspecon while the sensor is running. Changes are automacally saved as they are made.
1.
From the Sensor screen, click in the upper right corner to view the inspecon list.
2.
Click Add New Inspecon.
A new inspecon is added to the list, the Image pane updates, and the Tools & Results tab shows only the camera tool.
3.
Add tools and adjust them as needed for the inspecon.
Add a Tool
1.
Click on the Tools & Results tab.
The Add Tool window opens.
2.
Click the desired tool.
Tool Name Descripon
Average Gray
Evaluates pixel brightness within an ROI and computes the average grayscale value.
Bead
Inspects parts for uniformity of adhesive or sealant material, or for uniformity of a gap.
Blemish
Determines whether aws are present on a part, or detects whether a feature exists on a part.
Blob
Detects and counts/locates groups of connected light or dark pixels within the ROI and designates them as blobs (Binary Large
Objects). Aer blobs are found, they can be characterized by size and shape.
Circle Detect
Detects a single circle or piece of a circle (arc).
Edge
Detects and counts transions between bright and dark pixels (edges). Counts the total number of edges, and determines the
posion of each edge.
Line Detect
Locates a single, straight line segment by nding edge points along bright or dark pixel transions and ng a line to those
points.
Locate
Finds the rst edge on a part and compensates for translaon and rotaon of downstream tools (if selected).
Match
Veries that a paern, shape, or part in any orientaon matches a reference paern. Can also compensate for translaon and
rotaon of downstream tools (if selected).
Object
Detects the edges of dark and bright segments and locates their midpoints. Counts dark and bright segments, and measures the
width of each dark and bright segment.
Math
Performs mathemacal
operaons using tool data or user-supplied constants. Includes basic arithmec, inequality expressions,
and stascal informaon.
Measure
Measures distance, calculates angles, and creates points and lines for use as inputs to other tools.
Logic
Uses Boolean logic to combine or convert tool results, or to drive discrete outputs from tool results. Logic tool data can be used
to evaluate the results of a single tool or mulple tools.
The tool is added to Tools & Results
and the region of interest (ROI) appears on the Image pane.
3. Congure the tool as needed for your applicaon.
a)
Resize
and rotate the ROI around the feature to be analyzed.
b) Dene or view parameters for the tool on the Input tab, such as ROI shape, threshold, or view the histogram.
c) Dene pass or fail criteria on the Test tab, such as the count, size, or match.
VE Series Smart Camera
P/N 191667 Rev. E www.bannerengineering.com - Tel: +1-763-544-3164 7
Save an Inspecon to a Computer, Network Drive, or Storage Device
Vision Manager
automacally saves inspecons to the VE as they are created and modied. Save a copy of the inspecon to your computer or another
network locaon if you want to be able to go back to previous sengs.
Use the following procedure to save a copy of an inspecon to your computer or a network locaon.
1.
On the
Inspecon Management screen, click Transfer.
2. Change the desnaon folder, if desired.
a)
Click
above the right column.
An explorer window opens.
b)
Navigate to the desired locaon, network locaon, or storage device.
c)
Click Select Folder.
The folder is selected and the window closes.
The path to the locaon displays above the right column.
3.
Select the desired
inspecon from the inspecon list in the le column.
4.
Click
.
Inspecon name.idb displays in the right column and the inspecon is transferred (saved) to the selected
locaon.
Congure the Discrete I/O
From the
System
Sengs screen, select Discrete I/O to change the discrete I/O sengs.
Figure 10. Discrete I/O
For more details, see the
Instrucon Manual.
Sensor Display
The LCD display on the top of the sensor provides access to view or change several sengs without using Vision Manager. The display provides limited
programming
opons:
• ETHER—Ethernet
sengs
• PCHANGE—Product change
• IO—Input/Output sengs
• IMAGE—Image sengs
• INFO—Sensor informaon
• SYSERROR—System errors, if present
• DISPLAY—Display sengs
• REBOOT—Reboot
Access the sensor menu by pressing Enter
from the Home Screen on the sensor display.
See the Instrucon Manual, p/n 191666, for more informaon.
VE Series Smart Camera
8 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 191667 Rev. E
Sensor Display Interface
Down and Up Buons
Press Down and Up to:
•
Navigate the menu systems
• Change programming sengs
When navigang the menu systems, the menu items loop.
Enter
Buon
Press Enter to:
• Access the Sensor Menu
• Access the submenus
• Save changes
In the Sensor Menu, a check mark
in the lower right corner of the display indicates that pressing Enter accesses a submenu.
Escape
Buon
Press Escape to:
• Leave the current menu and return to the parent menu
• Leave the current menu and return to the Home Screen from any menu
Important: Pressing Escape discards any unsaved changes.
In the Sensor Menu, a return arrow in the upper le corner of the display indicates that pressing Escape returns to the parent
menu.
Press and hold Escape for 2 seconds to return to the Home Screen from any menu.
VE Series Smart Camera
P/N 191667 Rev. E www.bannerengineering.com - Tel: +1-763-544-3164 9
Sensor Menu
Enter Shortcuts Menu
No
Yes
Yes
100 HD
100 FD
FOCUS#
Home
Screen
ETHER
PCHANGE
IO
VE Series User Interface
Enter
Top Menu
Top Menu
IMAGE
INFO
Sub Menus
or
or
Go Back to Parent Menu
Select Menu Item
Press to Save Setting
Press and Hold to Go Back
to Home Screen
SPEED
LINK
SUBNET
GATEWAY
STATUS
IP
PSELECT
TRIGGER
INPUT
MAC
MAX SPD
By NUM
OUTPUT
FW VER
BOOT
NAME
MODEL
HOUR
SERIAL
SLEEP
VIEW
Ethernet Menu
Product Change by Slot No.
Bit Representation of
Input/Output States
View Current
Focus No.
Sensor Info
(read-only)
DISPLAY
Display Settings
CLEAR
VIEW
SYSERR
System Error
No
Yes
REBOOT
Reboot Device
Return to Top
Yes
FOCUS#
TRIGGER
1000 FD
Figure 11. Menu Map
VE Series Smart Camera
10 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 191667 Rev. E
Specicaons
Power
12 V dc to 30 V dc (24 V dc ± 10% if a Banner light source is powered by the sensor)
Current: 400 mA maximum (exclusive of load and lights)
Use only with a suitable Class 2 power supply, or current liming power supply rated 12
V dc to 30 V dc, 1 A
Supply Protecon Circuitry
Protected against reverse polarity and transient overvoltages
Discrete I/O
1 Trigger IN
5 Programmable I/O
Output Conguraon
Opcally isolated
Output Rang
Output Resistance: < 2 Ω
Strobe Output Resistance: < 13 Ω
Programmable Output: 100 mA
External Strobe Output: 100 mA
O-State Leakage Current:
< 100 µA
External Light Maximum Current Draw
600 mA
Exposure Time
0.02 ms to 500 ms
Imager
VE200G1A: 6.9 mm × 5.5 mm, 8.7 mm diagonal (1/1.8-inch CMOS)
VE201G1A: 6.9 mm × 5.5 mm, 8.7 mm diagonal (1/1.8-inch CMOS)
VE202G1A: 7.2 mm × 5.4 mm, 9.0 mm diagonal (1/1.8-inch CMOS)
VE202G2A: 7.2 mm × 5.4 mm, 9.0 mm diagonal (1/1.8-inch CMOS)
Lens
C-mount
Pixel Size
VE200G1A: 5.3 µm
VE201G1A: 5.3 µm
VE202G1A: 4.5 µm
VE202G2A: 4.5 µm
Communicaon
10/100/1000
4
Mbps Ethernet
Memory
Device Sengs and Inspecon Storage Memory: 500 MB
Number of inspecon les: 999
Acquision
256 grayscale levels
Model Frames Per Second
5
Image Size
VE200G1A 60 fps, maximum 752 × 480 px
VE201G1A 60 fps, maximum 1280 × 1024 px
VE202G1A 50 fps, maximum 1600 × 1200 px
VE202G2A 50 fps, maximum 1600 × 1200 px
Torque—Tapped Holes for Mounng Screws
8 lbf·in (0.9 N·m) maximum torque
Construcon
Housing: Aluminum
Display Label: Polyester
Connecons
Ethernet: M12, 8-pin or 4-pin D-code Euro-style female
Light Connector: M8, 3-pin Pico-style female
Power, Discrete I/O: M12, 12-pin Euro-style male
Environmental Rang
IEC IP67 with an oponal lens cover properly installed
Operang
Condions
Operang Temperature: 0 °C to +50 °C (+32 °F to +122 °F)
95% maximum relave humidity (non-condensing)
Stable Ambient Lighng: No large, quick changes in light level; no direct or reected
sunlight
Storage Temperature: −30 °C to +70 °C (−22 °F to +158 °F)
Vibraon and Mechanical Shock
Meets EN 60947-5-2: 30 G Shock per IEC 60068-2-27; 1 mm amplitude from 10 - 60 Hz
per IEC 60068-2-6
Cercaons
Information
Technology
Equipment
E365235
Banner Engineering Corp. Soware Copyright Noce
This soware is protected by copyright, trade secret, and other intellectual property laws. You are only granted the right to use the soware and only for the purposes described by Banner. Banner reserves all other
rights in this soware. For so long as you have obtained an authorized copy of this soware directly from Banner, Banner grants you a limited, nonexclusive, nontransferable right and license to use this soware.
You agree not to use, nor permit any third party to use, this soware or content in a manner that violates any applicable law, regulaon or terms of use under this Agreement. You agree that you will not reproduce,
modify, copy, deconstruct, sell, trade or resell this soware or make it available to any le-sharing or applicaon hosng service.
Disclaimer of Warranes. Your use of this soware is enrely at your own risk, except as described in this agreement. This soware is provided "AS-IS." To the maximum extent permied by applicable law, Banner, it
aliates, and its channel partners disclaim all warranes, expressed or implied, including any warranty that the soware is t for a parcular purpose, tle, merchantability, data loss, non-interference with or non-
infringement of any intellectual property rights, or the accuracy, reliability, quality or content in or linked to the services. Banner and its aliates and channel partners do not warrant that the services are secure, free
from bugs, viruses, interrupon, errors, the or destrucon. If the exclusions for implied warranes do not apply to you, any implied warranes are limited to 60 days from the date of rst use of this soware.
Limitaon of Liability and Indemnity. Banner, its aliates and channel partners are not liable for indirect, special, incidental, punive or consequenal damages, damages relang to corrupon, security, loss or the
of data, viruses, spyware, loss of business, revenue, prots, or investment, or use of soware or hardware that does not meet Banner minimum systems requirements. The above limitaons apply even if Banner and
its
aliates and channel partners have been advised of the possibility of such damages. This Agreement sets forth the enre liability of Banner, its aliates and your exclusive remedy with respect to the soware use.
You agree to indemnify and hold Banner and its aliates and channel partners harmless from any and all claims, liability and expenses, including reasonable aorney's fees and costs, arising out of your use of the
Services or breach of this Agreement (collecvely referred to as "Claims"). Banner reserves the right at its sole discreon and at its own expense, to assume the exclusive defense and control of any Claims. You agree
to reasonably cooperate as requested by Banner in defense of any Claims.
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any
product of its manufacture which, at the me it is returned to the factory, is found to have been defecve during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the
improper applicaon or installaon of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discreon of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR
ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO
USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligaons or liabilies relang to any product previously manufactured by Banner
Engineering Corp. Any misuse, abuse, or improper applicaon or installaon of this product or use of the product for personal protecon
applicaons when the product is idened as not intended for such purposes
will void the product warranty. Any modicaons to this product without prior express approval by Banner Engineering Corp will void the product warranes. All specicaons published in this document are subject
to change; Banner reserves the right to modify product specicaons or update documentaon at any me. Specicaons and product informaon in English supersede that which is provided in any other language.
For the most recent version of any documentaon, refer to: www.bannerengineering.com.
4
1000 Mbps communicaon speed not available on 4-pin Ethernet models
5
This value can vary based on inspecon sengs.
VE Series Smart Camera
©
Banner Engineering Corp. All rights reserved
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Banner VE202G1A Quick start guide
- Category
- Power tools
- Type
- Quick start guide
Banner VE202G1A is a self-contained smart camera with user-friendly Vision Manager software. It offers high-resolution 2 MP grayscale images (1600 x 1200 pixels) for precise inspection tasks. With various image processing tools and capabilities, it can solve a wide range of vision applications, including item detection, part positioning, feature measurement, and flaw analysis. The intuitive Vision Manager software allows for easy setup, run-time editing, and offline troubleshooting.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Banner VE202G2A User manual
-
-
Banner Q4X Series Quick start guide
-
-
-
Banner SureCross DX80 User manual
-
-
-
-
Banner ZMX Series User guide
