superbrightleds com RGBCCT-MZ8-RF User manual

Brand: superbrightleds com

Model: RGBCCT-MZ8-RF

Type: User manual

RGB+CCT Controller Module

User Manual

Important: Read all instructions prior to installation. RGBCCT6-MZ

Included Parts

Specications

RGBCCT6-MZ

operating voltage range 12–24 VDC

radio frequency 2.4 GHz

electrical connection hardwire or coaxial power connector

with 5.5 mm outer diameter and 2.1

mm inner diameter

operating temperature -4–140° F (-20–60° C)

warranty 2 Years

Compatible Remote Controls

One of these controls (available at additional cost) is required

to operate the controller module. Each light can be linked with

up to 4 dierent remote controls (any combination of wireless

remotes and Wi-Fi controls). Each control (and zone) can be

linked to an unlimited number of controller modules.

Signal Relay Function and Synchronization

Inputs from any linked remote control received by one module are

automatically relayed from that module to any additional modules

linked to remote within 100 ft (30 m) range. In addition, any modules

linked in same zone will automatically synchronize upon receiving

input from remote control—whether direct or relayed from another

controller module.

WIFI-CON2

(for smart phone control)

RGBCCT-MZ8-RF

1 1

8 8

1. Master On/O

Acts as a master On (-)/O (O) control for all linked RGBW and RGB+CCT lights. Also

activates the Master function, which allows remote to control lights of all zones. If a zone

is currently active, pressing Master On (-) button on remote or back button in app restores

Master function to the remote.

2. Color Selection Ring

Directly selects color along a circular spectrum. Press W button to changes to a

steady bright white.

3. Selection LED Indicator (wireless remote control only)

Flashes once to indicate when a command has been selected.

4. Brightness Touch Slider - Increase/Decrease

Increases (right side) or decreases (left side) the brightness level. Changing active mode

resets brightness level to full.

5. Saturation/CCT Touch Slider - Increase/Decrease

Increases (right side) or decreases (left side) the color saturation level. When controlling

white, adjusts from cool white (right side) to warm white (left side).

6. Mode

Nine distinct modes feature dierent color combinations, light transitions, and patterns.

On wireless remote, this button initiates mode function and scrolls through modes in

ascending order. In app, simply select mode button and press any numbered mode

button to switch between modes.

7. Mode Speed Increase/Decrease

Increases (S+ or +Speed) or decreases (S- or -Speed) speed of currently active mode.

8. Zones 1–8 On (|)/O (O)

Allows up to eight zones (channels) of RGBW and/or RCB+CCT lights to be separately

linked and controlled by remote/app. Pressing any Zone On(|) button activates that zone.

Commands will aect only lights in that zone. Once linked to a zone, lights remain linked until

they are unlinked.

9. White LED Selection

Switches to white LED operation.

Note: While functions remain the same, the phone/tablet display will vary in appearance from remote control.

Control Features

Light Modes

Mode Description Additional Control(s)

1 seven color, gradual transition saturation, speed, and brightness

2 white (mix of warm and cool), gradual transition speed and brightness

3 RGB, gradual transition saturation, speed, and brightness

4 seven color sequence, jump to change saturation, speed, and brightness

5 random color, jump to change saturation, speed, and brightness

6red light pulse then ash 3 times saturation, speed, and brightness

7green light pulse then ash 3 times saturation, speed, and brightness

8blue light pulse then ash 3 times saturation, speed, and brightness

9white (mix of warm and cool) light pulse then ash 3 times speed and brightness

1 - RGB+CCT Controller Module

Rev Date: V3 06/21/2023

4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com

Important: Read all instructions prior to installation.

Parts Included

Linking Lights to App Remote

Setup Instructions

1. Download MiBoxer app on compatible device (iOS or Android).

2. See WIFI-CON2 manual for complete instructions on how to establish connection

and set up Wi-Fi control.

Note: Constant 2.4 GHz Wi-Fi connection is required for remote access to Wi-Fi control

through your device.

Wi-Fi Control

Wireless Remote Control

1 - WIFI-CON2

1 - USB-500MA-5V

1 - RGBCCT-MZ8-RF

Linking Lights to Remote Control

Setup Instructions

Install two AAA batteries (not included) into wireless remote.

Note: Wireless remote operates using radio frequency and has 100 ft. (30 m) range.

• For indoor use only

• White color temperature can not be adjusted unless

White LED Selection mode is active.

FCC Statement

Safety and Notes

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired

operation. Any changes or modications in construction

of this device which are not expressly approved by the

party responsible for compliance could void the user’s

authority to operate the equipment.

Linking a Light

1. Make certain light is powered o.

Apply power. Within 3 seconds, press one of the eight Zone On (|) buttons three

times quickly until light begins ashing. Light will ash 3 times if successfully linked

to selected zone.

Note: If encountering issues when pairing, instead try continually pressing the

desired Zone On (|) button repeatedly from before when power is applied to the

controller until a few seconds after.

Activating and Controlling a Specic Zone

To activate a specic zone, press Zone On (|) button for desired zone. Zone

is now active and remote commands will only aect lights linked to that zone.

Unlinking a Light

1. Make certain light is powered o.

2. Apply power. Within 3 seconds, press the associated Zone On (|) button ve times

quickly until light begins ashing. Light will ash 10 times if successfully unlinked.

Linking a Light

1. Press the Link/Unlink button (1).

2. Select the desired zone.

3. Follow the on screen instructions to link the light.

Activating and Controlling a Specic Zone

To activate a specic zone, select one of the available zones and press On button.

Zone is now active and remote commands will only aect lights linked to that zone.

Unlinking a Light

1. Make certain the light is powered o.

2. Press the Link/Unlink button (1).

3. Select the desired zone.

4. Press the unlink button to remove devices from the selected zone.

User Manual

RGBCCT6-MZ

Rev Date: V3 06/21/2023

4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com

superbrightleds com RGBCCT-MZ8-RF User manual

superbrightleds com RGBCCT-MZ8-RF User manual

superbrightleds com RGBCCT-MZ8-RF User manual

Related papers

Other documents