2. Thermo Fisher Scientific
  3. IonPac Mixer

Thermo Fisher Scientific IonPac Mixer Operating instructions

  • Hello! I have reviewed the instructions for the IonPac Mixer 061645. This document provides instructions on how to connect tubing, replace the frit, and use the necessary plastic fittings. I'm ready to answer your questions about the IonPac Mixer and its use based on the manual.
  • Is the IonPac Mixer ready to use upon delivery?
    What type of fittings should be used with the IonPac Mixer?
    How do I replace the frit in the IonPac Mixer?
Errata
IonPac Mixer Instructions For Use
031979-01
For new orders of the following parts discussed in this manual, please use the updated part
numbers listed below.
Part Old Part Number in this
manual Updated Part Number to
use for new orders
PROD,COL,IP,MXR,SCS-1 061645 AAA-061645
IONPAC MIXER INSTRUCTIONS FOR USE
1. The IonPac Mixer (P/N 061645) is completely assembled and
ready for use.
2. Use fingertight fittings to connect the tubing to both ends of the
IonPac Mixer.
3. To replace the frit (P/N 062889) in the IonPac Mixer,
disconnect the tubing, unscrew one filter end fitting, remove the
old frit, and place a new frit into the cavity of this end fitting.
4. Retighten the filter end fitting with a wrench, ¼ turn past hand
tight and then reconnect the tubing.
Caution: Use only plastic fittings with the IonPac Mixer.
Document No. 031979-01 30 January 2004
IONPAC MIXER INSTRUCTIONS FOR USE
1. The IonPac Mixer (P/N 061645) is completely assembled and
ready for use.
2. Use fingertight fittings to connect the tubing to both ends of the
IonPac Mixer.
3. To replace the frit (P/N 062889) in the IonPac Mixer,
disconnect the tubing, unscrew one filter end fitting, remove the
old frit, and place a new frit into the cavity of this end fitting.
4. Retighten the filter end fitting with a wrench, ¼ turn past hand
tight and then reconnect the tubing.
Caution: Use only plastic fittings with the IonPac Mixer.
Document No. 031979-01 30 January 2004
IONPAC MIXER INSTRUCTIONS FOR USE
1. The IonPac Mixer (P/N 061645) is completely assembled and
ready for use.
2. Use fingertight fittings to connect the tubing to both ends of the
IonPac Mixer.
3. To replace the frit (P/N 062889) in the IonPac Mixer,
disconnect the tubing, unscrew one filter end fitting, remove the
old frit, and place a new frit into the cavity of this end fitting.
4. Retighten the filter end fitting with a wrench, ¼ turn past hand
tight and then reconnect the tubing.
Caution: Use only plastic fittings with the IonPac Mixer.
Document No. 031979-01 30 January 2004
IONPAC MIXER INSTRUCTIONS FOR USE
1. The IonPac Mixer (P/N 061645) is completely assembled and
ready for use.
2. Use fingertight fittings to connect the tubing to both ends of the
IonPac Mixer.
3. To replace the frit (P/N 062889) in the IonPac Mixer,
disconnect the tubing, unscrew one filter end fitting, remove the
old frit, and place a new frit into the cavity of this end fitting.
4. Retighten the filter end fitting with a wrench, ¼ turn past hand
tight and then reconnect the tubing.
Caution: Use only plastic fittings with the IonPac Mixer.
Document No. 031979-01 30 January 2004
IONPAC MIXER INSTRUCTIONS FOR USE
1. The IonPac Mixer (P/N 061645) is completely assembled and
ready for use.
2. Use fingertight fittings to connect the tubing to both ends of the
IonPac Mixer.
3. To replace the frit (P/N 062889) in the IonPac Mixer,
disconnect the tubing, unscrew one filter end fitting, remove the
old frit, and place a new frit into the cavity of this end fitting.
4. Retighten the filter end fitting with a wrench, ¼ turn past hand
tight and then reconnect the tubing.
Caution: Use only plastic fittings with the IonPac Mixer.
Document No. 031979-01 30 January 2004
IONPAC MIXER INSTRUCTIONS FOR USE
1. The IonPac Mixer (P/N 061645) is completely assembled and
ready for use.
2. Use fingertight fittings to connect the tubing to both ends of the
IonPac Mixer.
3. To replace the frit (P/N 062889) in the IonPac Mixer,
disconnect the tubing, unscrew one filter end fitting, remove the
old frit, and place a new frit into the cavity of this end fitting.
4. Retighten the filter end fitting with a wrench, ¼ turn past hand
tight and then reconnect the tubing.
Caution: Use only plastic fittings with the IonPac Mixer.
Document No. 031979-01 30 January 2004
IONPAC MIXER INSTRUCTIONS FOR USE
1. The IonPac Mixer (P/N 061645) is completely assembled and
ready for use.
2. Use fingertight fittings to connect the tubing to both ends of the
IonPac Mixer.
3. To replace the frit (P/N 062889) in the IonPac Mixer,
disconnect the tubing, unscrew one filter end fitting, remove the
old frit, and place a new frit into the cavity of this end fitting.
4. Retighten the filter end fitting with a wrench, ¼ turn past hand
tight and then reconnect the tubing.
Caution: Use only plastic fittings with the IonPac Mixer.
Document No. 031979-01 30 January 2004
IONPAC MIXER INSTRUCTIONS FOR USE
1. The IonPac Mixer (P/N 061645) is completely assembled and
ready for use.
2. Use fingertight fittings to connect the tubing to both ends of the
IonPac Mixer.
3. To replace the frit (P/N 062889) in the IonPac Mixer,
disconnect the tubing, unscrew one filter end fitting, remove the
old frit, and place a new frit into the cavity of this end fitting.
4. Retighten the filter end fitting with a wrench, ¼ turn past hand
tight and then reconnect the tubing.
Caution: Use only plastic fittings with the IonPac Mixer.
Document No. 031979-01 30 January 2004
/